Your Destination for Mobility Engineering Resources
Announcements for SAE Mobilus
Browse AllRecent SAE Edge™ Research Reports
Browse All 177Latest Journal Issues
Browse All 16
Recent Books
Browse All 719Recently Published
Browse AllAs acoustic requirements for NVH trim components become increasingly constrained by mass, cost, and sustainability targets, traditional approaches to inner dash design based on spatially averaged Transmission Loss (TL) metrics are reaching their practical limits. In fully built vehicles, the acoustic performance of the inner dash is governed by its global insulation capability but also by strong spatial heterogeneity and its interaction with spatially distributed noise sources such as the power unit, gearbox, and tyre-road excitation. This paper presents a test-based methodology for the spatial optimisation of inner dash acoustic performance using reciprocal holography. By applying a calibrated sound power source within the vehicle cabin and measuring the reciprocal response in the engine bay and wheel-arch regions, a high-resolution spatial Transmission Loss “hologram” of the inner dash is obtained under in-situ conditions. The resulting spatial data enables the identification of
In this study, we propose a methodology for predicting the acoustic modes and natural frequencies of a sedan using artificial intelligence and demonstrate the feasibility of controlling its acoustic characteristics by modifying the hole distribution of the package tray. In typical sedan structures, the cabin cavity and trunk cavity are acoustically coupled through holes in the package tray. The distribution of these holes significantly affects the natural acoustic modes and frequencies of the vehicle. However, once the exterior shape of the vehicle is finalized during the design stage, options for structural modifications to mitigate noise issues caused by these modes become extremely limited. To address this challenge efficiently, we develop a deep learning-based neural network model trained on data derived from a simplified acoustic analysis model of a sedan that includes a package tray. Finite element analysis is performed to generate acoustic modes and natural frequencies, which
The rapid electrification of the automotive industry introduces new challenges in noise, vibration, and harshness (NVH). In particular, in a virtual prototyping phase of the e-vehicles development, the rubber mounts are often one of the key elements to be considered when analysing the structure borne noise contributions. Having an accurate experimental characterization of the mount dynamic stiffness curves is therefore very relevant. However, conventional mount characterization methods are often pushed to their limits, partly due to the use of stiffer bushings, and partly because the frequency range of interest is extended toward higher frequencies. When using inverse substructuring, the dynamic stiffness curves can be obtained from frequency response function measurements. The required test setup consists of excitations and responses, located on each side of the mount via dedicated fixtures. The measured frequency response functions are reduced into 6 degrees of freedom representation
The virtual development of Electric Drive Modules (EDMs) for Battery Electric Vehicles (BEVs) requires proven and predictive methodologies. One part of the development investigates the vibro-acoustic assessment for the low- and high-frequency ranges within the targeted operating range. The efficient use of such a methodology requires an understanding of the accuracy and validity of the achievable results, as well as the derivation of suitable improvement measures for goals that have not been achieved. The use of reference data from experimental investigations and a detailed root cause analysis (RCA), to directly link a specific response and behavior to the excitations, modal content, and transfer functions, is an essential and non-trivial part of the methodology development. This paper describes the development of such a methodology using the example of a new EDM virtual model for Noise, Vibration and Harshness (NVH) analysis, including the simulation approach, validation, and
Realistic seat vibration reproduction is essential for delivering authentic haptic cues and enhancing driver immersion in driving simulators. Unlike direct playback of road recordings, simulator applications require vibration synthesis that responds interactively to driver inputs and vehicle dynamics. Reproducing these vibrations at the seat is often complicated by actuator bandwidth limitations and the dynamic behaviour of the seat structure itself, which can alter the intended target response. This work presents vibration synthesis and seat dynamics compensation strategies implemented on a single-axis seat vibration reproduction system equipped with a vertical actuator. Frequency Response Functions (FRFs) were measured to characterise the system dynamics under single-axis excitation. Run-up and coast-down tests were conducted on the seat and compared to target responses measured on an actual vehicle under operational conditions. Several seat dynamics compensation strategies were
The simulation of structure-borne energy flow within a full vehicle trimmed body at mid and high frequencies has always been a challenge due to the large computational cost associated with standard deterministic simulations. This is a particularly pressing problem given that the electrification of the vehicles is extending the presence of structure-borne sources to higher frequencies. While the improvement of computational hardware has allowed OEMs to shift the limit of standard Finite Element (FE) approaches to higher frequencies, no methods have been proposed in the literature that tackle the full frequency range for industrial-sized problems. In this paper, a simulation methodology that uses wave-based processing of the original low-frequency finite element input deck to compute the coupling loss factors is proposed to model structure-borne noise in complex systems at mid and high frequencies. The methodology is validated against numerical and experimental data.
In the automotive industry, controlling noise transmission through vehicle components is essential for passenger comfort and regulatory compliance. Traditionally, Transmission Loss (TL) is estimated using simplified CAD-based metrics, which lack accuracy at high frequencies and for complex assemblies. Modeling complex vehicle components introduces challenges, such as representing fluid-structure and trim interactions, with spatially varying trim thicknesses. This study presents an industrial application implementing the Virtual SEA (Statistical Energy Analysis) method to evaluate TL for a firewall. The study discusses strategies for subsystem adaptation and analytical trim modeling, highlighting the importance of managing spatial averaging effects. The proposed workflow integrates laboratory measurements of trim materials, advanced subsystem definition, diffuse sound field (DSF) excitation and radiation in free-field condition. Virtual SEA results are systematically validated against
Electric vehicle subsystems, including powertrains, electric motors, and gearboxes, pose new challenges in achieving stringent acoustic performance targets for both interior and exterior noise. These challenges are intensified by increasingly demanding customer expectations regarding interior acoustic comfort, which encompasses the reduction of intrusive noise sources and the enhancement of overall sound quality across a broad frequency spectrum. A primary concern associated with electric vehicles subsystems is the generation of high-frequency tonal noise, commonly referred to as whine noise, which can significantly impact acoustic performance and passenger comfort. High-frequency whine noise propagates through multiple transmission paths and can be effectively attenuated at the source through encapsulation strategies, which also contribute to broadband noise reduction across a wide frequency spectrum. To predict the acoustic performance of encapsulation, a coupled simulation approach
Tire exterior noise has become increasingly critical in vehicle acoustics due to two key developments: updated pass-by noise regulations, which amplify the relative contribution of tire noise, and the rise of Battery Electric Vehicles (BEVs), which lack traditional powertrain noise. Design trends in BEVs—such as increased vehicle mass from battery packs and the widespread use of large-diameter, wide, low-profile tires—further intensify tire noise due to stiffer constructions and altered contact dynamics. A common method for predicting tire noise is the source-transfer-receiver model, where the tire is represented by a set of monopoles with volume velocity Q derived from near-field measurements. Acoustic propagation is modeled via p/Q transfer functions. Despite its simplifications, this approach is practical for vehicle development, enabling clear separation between source and transfer mechanisms and facilitating targeted noise control strategies. In previous work, we proposed a
Recent studies indicate that the door system plays a significant role in the interior noise levels of newly developed vehicles. This research investigates the noise transmission paths through the door system and identifies effective strategies for improvement through a combination of door buck testing and simulation. Specifically, in this study, the finite element method (FEM) was employed for door buck simulation, and the model was validated against vibration test results. Subsequently, acoustic analysis tools were utilized to correlate with noise testing, thereby establishing a process to ensure simulation accuracy. The sound insulation performance for the main areas of the door was experimentally evaluated, and a simulation model with good correlation to these test results was developed. By utilizing both experimental and simulation results, the principal transmission paths were identified, and appropriate improvement strategies for these paths were investigated. The validated