Standards - SAE Mobilus

SAE standards are internationally recognized as some of the most trusted collections of scientific data to globally optimize the processes, practices, and products that advance technology in our industry and are vital to ensure safety, quality, and reliability. Over 40,000+ current documents available within the aerospace, automotive, and commercial vehicle industries.

Items (48,730)
This document provides background information, rationale, and data (both physical testing and computer simulations) used in defining the component test methods and similarity criteria described in SAE Aerospace Recommended Practice (ARP) 6330. ARP6330 defines multiple test methods used to assess the effect of seat back mounted IFE monitor changes on blunt trauma to the head and post-impact sharp edge generation. The data generated is based on seat and IFE components installed on type A-T (transport airplane) certified aircraft. While not within the scope of ARP6330, generated test data for the possible future development of surrogate target evaluation methods is also included
Aircraft Seat Committee
This SAE Aerospace Recommended Practice (ARP) provides recommendations for: The audit process in general A list of specific areas of attention to be audited Maintaining the test facility in such a manner that it meets audit requirements
EG-1E Gas Turbine Test Facilities and Equipment
To provide specifications for lighting and marking of industrial wheeled equipment whenever such equipment is operated or traveling on a highway
OPTC3, Lighting and Sound Committee
This specification covers a corrosion- and heat-resistant steel in the form of seamless tubing
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers an aircraft-quality, low-alloy steel in the form of bars and forgings 1.50 inches or less in diameter or least distance between parallel sides (thickness
AMS E Carbon and Low Alloy Steels Committee
This specification covers a corrosion-resistant steel in the form of wire
AMS F Corrosion and Heat Resistant Alloys Committee
The following terminology has been generated by the ATA/IATA/SAE Commercial Aircraft Composite Repair Committee (CACRC) and provides terminology for design, fabrication, and repair of composite and bonded metal structures
AMS CACRC Commercial Aircraft Composite Repair Committee
This specification covers a rust removing compound in the form of a solid, generally powdered, to be dissolved in water, and heated
AMS J Aircraft Maintenance Chemicals and Materials Committee
This document has been prepared and issued to provide information and guidance on the application of AQAP 2110 when the Supplier adheres to the provisions of 9100. This document is published as AQAP 2009 Annex F and 9137. It was jointly developed by NATO and industry representatives for use by NATO and industry to facilitate the use and understanding of the relationship between the AQAP 2110 and 9100
G-14 Americas Aerospace Quality Standards Committee (AAQSC)
This SAE practice is intended for the sample preparation of test pieces for automotive wheels and wheel trim. The practice provides a consistent scribing method for use on test panels and or component parts with substrate chemical pretreatment and coating systems. Test specimens can then be subjected to various corrosion tests in order to evaluate performance without significant variations of the degree of exposure of the substrate. The scribing is used to create a break in the coating/finishing as can occur in the field through gravel and other damaging conditions. NOTE— Significant variability is attributed to surface contour, coating hardness/softness, operator reproducibility, and the scribing tool and it’s condition
Wheel Standards Committee
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design of flanges on temperature sensors intended for use in gas turbine engines. Three figures detail the configuration of standard size flange mounts with bolt holes, slotted flanges, and miniaturized flanges for small probes
E-32 Aerospace Propulsion Systems Health Management
This Aerospace Recommended Practice (ARP) is a general overview of typical airborne engine vibration monitoring (EVM) systems applicable to fixed or rotary wing aircraft applications, with an emphasis on system design considerations. It describes EVM systems currently in use and future trends in EVM development. The broader scope of Health and Usage Monitoring Systems, (HUMS) is covered in SAE documents AS5391, AS5392, AS5393, AS5394, AS5395, AIR4174. This ARP also contains the essential elements of AS8054 which remain relevant and which have not been incorporated into Original Equipment Manufacturers (OEM) specifications
E-32 Aerospace Propulsion Systems Health Management
This SAE Aerospace Recommended Practice (ARP) defines the nomenclature of temperature measuring devices. General temperature measurement related terms are defined first, followed by nomenclature specifice to temperature measuring devices, particularly thermocouples
E-32 Aerospace Propulsion Systems Health Management
This standard specifies the communications hardware and software requirements for fueling hydrogen surface vehicles (HSV), such as fuel cell vehicles, but may also be used where appropriate with heavy-duty vehicles (e.g., buses) and industrial trucks (e.g., forklifts) with compressed hydrogen storage. It contains a description of the communications hardware and communications protocol that may be used to refuel the HSV. The intent of this standard is to enable harmonized development and implementation of the hydrogen fueling interfaces. This standard is intended to be used in conjunction with the hydrogen fueling protocols in SAE J2601 and nozzles and receptacles conforming with SAE J2600
Fuel Cell Standards Committee
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and foil 0.1874 inch (4.76 mm) and under in nominal thickness
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a corrosion- and heat-resistant, work-strengthened, and aged cobalt-nickel-chromium alloy in the form of bars 2 inches (50 mm) and under in nominal diameter
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers an aluminum alloy in the form of sheet 0.040 to 0.249 inches (1.02 to 6.32 mm), inclusive, in nominal thickness (see 8.5
AMS D Nonferrous Alloys Committee
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings 10.0 inches (254 mm) and under in nominal diameter or distance between parallel sides, and stock of any size for forging, flash-welded rings, or heading
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports
Test Methods and Equipment Stds Committee
SAE J3072 establishes requirements for a grid support inverter system function that is integrated into a plug-in electric vehicle (PEV), which connects in parallel with an electric power system (EPS) by way of conductively coupled, electric vehicle supply equipment (EVSE). This standard also defines the communication between the PEV and the EVSE required for the PEV onboard inverter function to be configured and authorized by the EVSE for discharging at a site. The requirements herein are intended to be used in conjunction with IEEE 1547-2018 and IEEE 1547.1-2020 or later versions
Hybrid - EV Committee
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a Ability of the parking brake system to lock the braked wheels. b The trailer holding or sliding on the grade, fully loaded, or unloaded. c Applied manual effort. d Unburnished or burnished brake lining friction conditions. e Down and upgrade directions
Truck and Bus Brake Systems Committee
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR
Truck and Bus Foundation Brake Committee
This Aerospace Information Report (AIR) is intended to provide information relating to the construction, calibration, and usage of parallel plate transmission lines in electromagnetic compatibility susceptibility testing
AE-4 Electromagnetic Compatibility (EMC) Committee
This AIR was prepared to inform the aerospace industry about the electromagnetic interference measurement capability of spectrum analyzers. The spectrum analyzers considered are of the wide dispersion type which are electronically tuned over an octave or wider frequency range. The reason for limiting the AIR to this type of spectrum analyzer is that several manufacturers produce them as general-purpose instruments, and their use for EMI measurement will give significant time and cost savings. The objective of the AIR is to give a description of the spectrum analyzers, consider the analyzer parameters, and describe how the analyzers are usable for collection of EMI data. The operator of a spectrum analyzer should be thoroughly familiar with the analyzer and the technical concepts reviewed in this AIR before performing EMI measurements
AE-4 Electromagnetic Compatibility (EMC) Committee
This specification covers a polysulfide sealing compound with low adhesive strength, supplied as a two-component system that cures at room temperature
AMS G9 Aerospace Sealing Committee
This specification covers one type of copper alloy (brass) in the form of bars and rods up to 4.000 inches (101.60 mm) in nominal diameter, thickness between parallel sides, or width as defined in Tables 3 through 6 (see 8.6
AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of rolled or cold finished bars and rods of the sizes specified in 3.3.1.1 (see 8.5
AMS D Nonferrous Alloys Committee
This SAE Recommended Practice provides test methods and criteria for evaluating the internal cleanliness and air leakage for engine charge air coolers. This SAE Recommended Practice also provides nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air cooling system operational performance parameters
Cooling Systems Standards Committee
This recommended practice establishes the requirements and procedures for Barkhausen Noise (BN) inspection of ferromagnetic steel components. See Appendix B for a list of common materials for BN inspection. Applications of the method are listed in 1.2 through 1.5
AMS K Non Destructive Methods and Processes Committee
This specification covers an acrylonitrile-butadiene (NBR) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. For molded rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the AMS-P-83461 specification or the MIL-PRF-25732 specification
AMS CE Elastomers Committee
This specification covers procedures for identifying wrought products of titanium and titanium alloys
AMS G Titanium and Refractory Metals Committee
This SAE Standard provides test procedures, requirements, and guidelines for stop lamps intended for use on vehicles of less than, equal to, or greater than 2032 mm in overall width
Signaling and Marking Devices Stds Comm
This practice presents methods for establishing the driver workspace. Methods are presented for: Establishing accelerator reference points, including the equation for calculating the shoe plane angle. Locating the SgRP as a function of seat height (H30). Establishing seat track dimensions using the seating accommodation model. Establishing a steering wheel position. Application of this document is limited to Class-A Vehicles (Passenger Cars, Multipurpose Passenger Vehicles, and Light Trucks) as defined in SAE J1100
Human Accom and Design Devices Stds Comm
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft
Marine Technical Steering Committee
The purpose of this document is to provide detailed requirements to preclude the acquisition and use of suspect counterfeit or counterfeit bearings and/or bearing components/materiel. The term bearings referenced throughout this document includes bearings and/or bearing components/materiel (e.g., balls, races, lubricant, cage, seal). The requirements of this document supplement the requirements of a higher-level quality standard (e.g., AS/EN/JISQ9100, ISO 9001, ANSI/ASQ E4, ASME NQA-1, AS9120, AS9003, and IATF 16949 or equivalent) and other quality management system documents. All appendices are provided for guidance and are not mandatory
G-21 Counterfeit Materiel Committee
Test procedures are described for measuring noise at specific receiver locations (passenger and cargo doors, and servicing positions) and for conducting general noise surveys around aircraft. Procedures are also described for measuring noise level at source locations to facilitate the understanding and interpretation of the data. Requirements are identified with respect to instrumentation; acoustic and atmospheric environment; data acquisition, reduction and presentation, and such other information as is needed for reporting the results. This document makes no provision for predicting APU or component noise from basic engine characteristics or design parameters, nor for measuring noise of more than one aircraft operating at the same time. No attempt is made to suggest acceptable levels of noise or suitable subjective criteria for judging acceptability. ICAO Annex 16 Volume I Attachment C provides guidance on recommended maximum noise levels
A-21 Aircraft Noise Measurement Aviation Emission Modeling
This SAE Aerospace Information Report (AIR) is intended to be used as a process verification guide for evaluating implementation of key factors in repair of metal bond parts or assemblies in a repair shop environment. This guide is to be used in conjunction with a regulatory approved and substantiated repair and is intended to promote consistency and reliability
AMS CACRC Commercial Aircraft Composite Repair Committee
This document derives from the Federal Motor Vehicle Safety Standards (FMVSS) 105 and 135 vehicle test protocols as single-ended inertia-dynamometer test procedures. The test sequences enable brake output measurement, friction material effectiveness, and corner performance in a controlled and repeatable environment. This SAE Document also includes optional sections for parking brake output performance for rear brakes with hydraulic or Electric Park Brakes (EPB). It applies to brake corners from vehicles covered by the FMVSS 105 and 135 when using the appropriate brake hardware and test parameters. The FMVSS 135 applies to all passenger cars and light trucks up to 3500 kg of gross vehicle weight (GVWR). The FMVSS 105 applies to all passenger cars, multi-purpose vehicles, buses, and trucks above 3500 kg of GVWR. This document does not include testing for school bus applications or vehicles equipped with hydraulic brakes with a GVWR above 4540 kg. This document does not evaluate or
Brake Dynamometer Standards Committee
This SAE Aerospace Standard (AS) establishes standard requirements for aerospace sealants and adhesion promoters, which may be incorporated as part of SAE Aerospace Material Specifications (AMS) for such products. This document provides for commonality of methods and procedures for responsibility for inspection, source inspection, classification of tests, establishment of/and qualification to qualified products lists, approval, reports, resampling and retesting, packaging, and marking
AMS G9 Aerospace Sealing Committee
This specification covers a magnesium alloy in the form of welding wire (see 8.5
AMS D Nonferrous Alloys Committee
This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Items per page:
1 – 50 of 48730