Browse Topic: Cobalt alloys

Items (1,276)
Find
Test the Corrosion Effect on High Hard Steel Armor MIL-DTL-46100 Coated with Stellite 6 Applied by Direct Energy Deposition Method2024-01-381311/15/2024
ABSTRACT The U.S. Army - GVSC Materials Characterization and Failure Analysis team conducted a preliminary study in FY18 to address the issue of galvanic and pitting corrosion of U.S. Army ground vehicle system (GVS) structural surfaces. The objective of this study was to develop a permanent coating solution to supplement the existing corrosion protective coating of zinc rich primer and CARC paint, and extend the lifecycle of the armor. Twenty-five permanent, 0.1 inch layer, additively manufactured (AM) coated coupons of deposited Stellite 6 cobalt alloy on MIL-STD-46100 High Hard (HH) armor steel blocks were produced for cyclic testing using an un-optimized set of parameters. These coupons were subjected to a twenty-four week study in accelerated corrosive conditions of a fog spray chamber alongside primer-CARC coated and uncoated coupons. The resulting study showed no signs of pitting corrosion in the surface of the AM coated coupons, and minimal galvanic corrosion. Citation: I
Toppler, Ian J, Schleh, Daniel C, Romero, Claudio Gutierrez
Technical Paper
Heat Treatment, Nickel Alloy and Cobalt Alloy PartsAMS2774H (Current)08/29/2024
This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or subcontractors, of parts made of wrought or additively manufactured nickel or cobalt alloys, of raw materials during fabrication, and of fabricated assemblies in which wrought nickel or cobalt alloys are the primary structural components
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion- and Heat-Resistant, Strip 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Plus Consumable Electrode Remelted Solution Heat Treated and Cold RolledAMS5876F (Current)10/16/2023
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of strip 0.100 inch (2.54 mm) and under in specified thickness and 4.000 inches (101.60 mm) and under in specified width in the solution heat-treated and cold rolled condition
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion- and Heat-Resistant, Welding Wire 39Co - 22Cr - 22Ni - 14.5W - 0.07La (188AMS5801H (Current)09/28/2023
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Alloy, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Rings and Stock for Forgings, Rings and Heading 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N - 31Fe Solution and Precipitation Heat TreatedAMS5768M (Current)06/12/2023
This specification covers a corrosion- and heat-resistant iron-chromium-nickel-cobalt alloy in the form of bars, wire, forgings, flash welded rings, and stock for forging, flash welded rings, or heading
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, and Rings and Stock for Forgings and Rings 74Ni - 15.5Cr - 8.0FeAMS5665R (Current)05/30/2023
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars and forgings, flash welded rings, and stock for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Sheet, Strip, Foil and Plate 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode Remelted or Vacuum Induction Melted 1775 °F (968 °C) Solution Heat TreatedAMS5596N (Current)05/22/2023
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, foil, and plate 1.00 inch (25.4 mm) and under in thickness
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Seamless Tubing 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1950 °F (1066 °C) Solution Heat TreatedAMS5590G (Current)05/16/2023
This specification covers a corrosion and heat-resistant nickel alloy in the form of seamless tubing having nominal OD of 0.125 inch (3.18 mm) and over with nominal wall thickness of 0.015 inch (0.38 mm) and over (see 8.5
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion- and Heat-Resistant, Welding Wire 52Co - 20Cr - 10Ni -15WAMS5796F (Current)05/16/2023
This specification covers a corrosion and heat-resistant cobalt alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion- and Heat-Resistant, Hard Facing Rods and Wire 62Co - 29Cr - 4.5W - 1.2CAMS5788G (Current)05/16/2023
This specification covers a corrosion and heat-resistant cobalt alloy in the form of welding rods, coating rods, or wrought wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Investment Castings 62Ni - 21.5Cr - 9.0Mo - 3.6Cb (Nb) As CastAMS5402D (Current)05/16/2023
This specification covers a corrosion and heat-resistant, air-melted, nickel alloy in the form of investment castings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Sheet, Strip, and Plate 74Ni - 15.5Cr - 8.0Fe AnnealedAMS5540R (Current)05/10/2023
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate up to 2.000 inches (50.80 mm), inclusive, in nominal thickness
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, and Rings Ni - 18Cr - 2.8Mo - 5.5Cb (Nb) - 0.70Ti - 1.50Al - 10Fe - 9Co - 1W Consumable Electrode Remelted or Vacuum Induction Melted 1775 °F (968 °C) Solution Heat Treated, Precipitation-HardenableAMS5441C (Current)04/04/2023
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings in the solution heat-treated condition, 5 inches (127 mm) and under in nominal diameter or least distance between parallel sides (thickness) having a maximum cross-sectional area of 50 square inches (323 cm2), and stock of any size for forging, flash welded rings, or heading
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Peening Media, General RequirementsAMS2431E (Current)04/04/2023
This specification and its detail slash specifications cover the requirements for media to be used in controlled shot peening of metal parts
AMS B Finishes Processes and Fluids Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, Rings, and Forging Stock 57Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4Al - 0.05Zr - 0.006B Consumable Electrode Remelted or Vacuum Induction Melted 1825 to 1900 °F (996 to 1038 °C) Solution, Stabilization, and Precipitation Heat TreatedAMS5707P (Current)03/23/2023
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings. Product covered by this specification is limited to a nominal 3.25 inches (82.6 mm) and under in diameter or maximum cross-sectional dimension between parallel sides (thickness) and stock of any size for forging and for flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion- and Heat-Resistant, Sheet, Strip, Foil, and Plate 52Co - 20Cr - 10Ni - 15W Solution Heat TreatedAMS5537K (Current)02/06/2023
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of sheet, strip, foil, and plate up to 2.250 inches (57.15 mm), inclusive, in nominal thickness
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Aircraft TubingAMS2263F (Current)12/20/2022
This specification covers established inch-pound manufacturing tolerances applicable to seamless and welded thin-wall aircraft tubing of nickel, nickel alloys, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions and are based on individual measurements, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of a specified range
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Wire 74Ni - 15.5Cr - 8.0Fe AnnealedAMS5687P (Current)12/16/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of wire 0.002 inch (0.05 mm) and over in nominal diameter
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Steel, Corrosion- and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 23Cr - 13.5Ni (309S) Solution Heat TreatedAMS5650G (Current)11/18/2022
This specification covers a corrosion and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Alloy Bars, Forgings, and Rings, Corrosion- and Heat-Resistant 73Ni - 15.5Cr - 2.5Ti - 0.70Al - 7.0Fe Precipitation HardenableAMS5714E (Current)11/18/2022
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings up to 4.000 inch (101.6 mm), inclusive, in nominal thickness or distance between parallel sides, and stock of any size for forging or flash welded rings (see 8.6
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 0.95Cb(Nb) - 2.5Ti - 0.70Al - 7.0Fe 1800 °F (982 °C) Solution Heat Treated, Precipitation HardenableAMS5747E (Current)11/18/2022
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings up to 4.00 inches, including (101.6 mm, including) in nominal diameter or least distance between parallel sides, and stock of any size for forging or flash welded rings (see 8.5
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Welding Wire 80Ni - 20CrAMS5676G (Current)11/02/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Steel, Corrosion- and Heat-Resistant, Bars, Forgings, Rings, and Forging Stock 13.5Cr - 13.5Ni - 0.35Mo - 2.2W AnnealedAMS5700H (Current)11/02/2022
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel-Copper Alloy Wire, Corrosion-Resistant 67Ni - 31Cu Annealed (400AMS4730J (Current)10/26/2022
This specification covers a corrosion-resistant nickel-copper alloy in the form of wire 0.002 inch (0.05 mm) in diameter and larger
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel-Copper Alloy, Corrosion-Resistant, Bars and Forgings 67Ni - 30CuAMS4675F (Current)10/26/2022
This specification covers a corrosion-resistant nickel-copper alloy in the form of bars 0.093 to 4.000 inches (2.35 to 100.00 mm) in diameter or distance between parallel sides, and forgings and forging stock of any size
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Ultrasonically Activated Needle Peen FormingAMS2588 (Current)10/26/2022
This specification covers the equipment and process requirements for forming or straightening metal parts using Ultrasonically Activated Needle Peening
AMS B Finishes Processes and Fluids Committee
Material Specification
Steel, Corrosion- and Heat-Resistant, Bars, Wire, Forgings, Mechanical Tubing, Rings, and Stock for Forgings and Rings 17Cr - 12Ni - 2.5Mo (316) Solution Heat TreatedAMS5648N (Current)10/07/2022
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars and Forgings, 57Ni - 20Cr - 10Co - 8.5Mo - 2.1Ti - 1.5Al - 0.005B, Vacuum Induction and Consumable Electrode Melted, Solution Heat Treated, Precipitation Heat TreatableAMS5915B (Current)10/07/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, and stock for forging
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel, Sheet and Strip Low (0.02 Max) Carbon AnnealedAMS5553J (Current)10/07/2022
This specification covers nickel in the form of sheet and strip 0.001 to 0.250 inch (0.03 to 0.65 mm), inclusive, in nominal thickness
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Chemical Check Analysis Limits Nickel, Nickel Alloys, and Cobalt AlloysAMS2269G (Current)09/14/2022
This specification defines limits of variation for determining acceptability of the composition of cast or wrought nickel, nickel alloy, and cobalt alloy parts and material acquired from a producer
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Iron-Nickel Alloy, Bars, Forgings, and Rings 42Fe - 37.5Ni - 14Co - 4.8Cb (Nb) - 1.6Ti Solution Heat Treated, Precipitation Hardenable Multiple Melted, High Temperature, Low ExpansionAMS5884E (Current)09/14/2022
This specification covers an iron-nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings, or heading
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Welding Wire 62.5Ni - 5.0Cr - 24.5Mo - 5.5FeAMS5786J (Current)09/08/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt-Nickel Alloy, Corrosion- and Heat-Resistant, Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb (Nb) - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Work Strengthened, and AgedAMS5843H (Current)09/08/2022
This specification covers a high strength, corrosion- and heat-resistant cobalt-nickel-chromium alloy in the form of bars 1-3/4 inches (44.4 mm) and under in nominal diameter
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel-Copper Alloy, Corrosion-Resistant, Sheet, Strip, and Plate 67Ni - 30Cu AnnealedAMS4544J (Current)08/26/2022
This specification covers a corrosion-resistant nickel-copper alloy in the form of sheet, strip, and plate
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Composition Testing Methods for Nickel- and Cobalt-Based AlloysAMS2283 (Current)08/19/2022
This specification establishes testing methods for testing chemical composition in nickel- and cobalt-based alloys
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, Rings, and Stock for Forgings and Rings, 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe, Consumable Electrode or Vacuum Induction Melted, 1775 °F (968 °C) Solution and Precipitation Heat TreatedAMS5663P (Current)08/19/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings in the solution and precipitation heat treated condition. Product covered by this specification is limited to 10.00 inches (254 mm) and under in nominal diameter or maximum cross-sectional dimension between parallel sides (thickness) and nominal cross sectional area of 78.54 in2 (503 cm2). Stock may be of any size for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, and Rings, 53Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B, Vacuum Melted, Solution and Precipitation Heat TreatedAMS5713L (Current)08/17/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars 3.00 inches (76.2 mm) and under in nominal diameter, thickness or for hexagons least distance between parallel sides, forgings, flash welded rings 3.00 inches (76.2 mm) and under in nominal radial thickness, and stock of any size for forging, flash welded rings, or heading
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, Rings, and Stock for Forgings and Rings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1775 °F (968 °C) Solution Heat Treated, Precipitation-HardenableAMS5662P (Current)08/17/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings in the solution heat treated condition. Product covered by this specification is limited to 10.00 inches (254 mm) and under in nominal diameter or maximum cross-sectional dimension between parallel sides (thickness) and nominal cross sectional area of 78.54 in2 (503 cm2) in cross-sectional area. Stock for forging, ring, or heading may be of any size
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, Extrusions, Rings, and Stock for Forgings and Rings 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1950 °F (1066 °C) Solution Heat Treated, Precipitation HardenableAMS5664G (Current)08/17/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings in the solution heat treated condition, Product covered by this specification is limited to 10.00 inches (254 mm) and under in nominal diameter or maximum cross-sectional dimension between parallel sides (thickness) and 78.54 square inches (503 cm2) in cross-sectional area. Stock may be of any size for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, and Rings 53Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B Vacuum Melted, Solution Heat Treated Precipitation HardenableAMS5712L (Current)08/17/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars 3.00 inches (76.2 mm) and under in nominal diameter, thickness or for hexagons least distance between parallel sides, forgings, flash welded rings 3.00 inches (76.2 mm) and under in nominal radial thickness, and stock of any size for forging, flash welded rings, or heading (see 8.5
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, and Rings Ni - 18Cr - 2.8Mo - 5.5Cb(Nb) - 0.70Ti - 1.50Al - 10Fe - 9Co - 1W Consumable Electrode Remelted or Vacuum Induction Melted 1775 °F (968 °C) Solution and Precipitation Heat TreatedAMS5442B (Current)08/04/2022
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings up to 5.0 inches (127mm) in least nominal cross-sectional dimension having a cross-sectional area not greater than 50 in2 (323 cm2), and stock of any size for forging or flash welded rings (see 8.5
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Steel, Corrosion-Resistant Bars, Forgings, Mechanical Tubing, and Rings and Forging Stock 15Cr - 6.5Ni - 0.75Mo - 0.50Cb (Nb) - 1.5Cu Solution Heat TreatedAMS5763F (Current)07/19/2022
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings 8.0 inches (200 mm) and under in in thickness, diameter or for hexagons least nominal cross-sectional dimension, and stock of any size for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Steel, Corrosion-Resistant, Bars, Wire, Forgings, Extrusions, Rings and Forging Stock 9.0Mn - 20Cr - 6.5Ni - 0.27N Solution Heat TreatedAMS5656G (Current)07/19/2022
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, extrusions, flash welded rings, and stock for forging, extruding, or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Iron-Nickel Alloy, Heat Resistant, Bars, Wire, Forgings, Rings and Stock for Rings and Forgings 44Fe - 18.5Cr - 35.5Ni - 1.1Si Solution Heat TreatedAMS5716L (Current)07/08/2022
This specification covers a heat-resistant iron-nickel alloy in the form of bars, wire, forgings, flash welded rings. Product covered by this specification is limited to 8.0 inches (203 mm) and under in nominal diameter or maximum cross sectional dimension between parallel sides (thickness), and stock of any size for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Bars, Forgings, Extrusions, Rings, and Stock for Forgings, Extrusions, and Rings 62Ni - 21.5Cr - 9.0Mo - 3.65Cb (Nb) AnnealedAMS5666K (Current)07/08/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, extrusions, flash welded rings up to 10 inches (254 mm) in diameter, thickness, or for hexagons, least distance between parallel sides, and stock of any size for forgings, extrusions, and rings
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion- and Heat-Resistant, Sheet, Strip, and Plate 40Co - 22Cr - 22Ni - 14.5W - 0.07La Solution Heat TreatedAMS5608H (Current)07/06/2022
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of sheet, strip, and plate
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Seamless or Welded Tubing 62Ni - 21.5Cr - 9.0Mo - 3.7Cb (Nb) AnnealedAMS5581G (Current)06/20/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of two types of tubing
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Welded Tubing 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe Solution Heat TreatedAMS5588H (Current)06/20/2022
This specification covers a corrosion- and heat-resistant nickel alloy in the form of welded and drawn tubing
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Nickel Alloy, Corrosion- and Heat-Resistant, Welding Wire 56Ni - 19.5Cr - 16.5Co - 2.5Ti - 1.5Al Vacuum Induction MeltedAMS5829F (Current)06/02/2022
This specification covers a corrosion and heat-resistant nickel alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Cobalt Alloy, Corrosion and Heat-Resistant, Welding Wire 52Co - 20Cr - 20Ni - 7.5Ta Vacuum MeltedAMS5814D (Current)06/02/2022
This specification covers a corrosion and heat-resistant cobalt alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
Material Specification
Items per page:
1 – 50 of 1276