Search
Advanced Search
of the following are true
(
)

Results

Items (210,997)
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
Engine Power Test Code Committee
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft
Marine Technical Steering Committee
This SAE Recommended Practice details the changes needed to support the SAE J2534 (API Version 05.00) on operating systems other than 32-bit Microsoft Windows
Vehicle E E System Diagnostic Standards Committee
This SAE Recommended Practice establishes uniform procedures for testing fuel cell and hybrid fuel cell electric vehicles, excluding low speed vehicles, designed primarily for operation on the public streets, roads and highways. The procedure addresses those vehicles under test using compressed hydrogen gas supplied by an off-board source or stored and supplied as a compressed gas onboard. This practice provides standard tests that will allow for determination of fuel consumption and range based on the US Federal Emission Test Procedures, using the Urban Dynamometer Driving Schedule (UDDS) and the Highway Fuel Economy Driving Schedule (HFEDS). Chassis dynamometer test procedures are specified in this document to eliminate the test-to-test variations inherent with track testing, and to adhere to standard industry practice for fuel consumption and range testing. Communication between vehicle manufacturer and the governing authority is essential when starting official manufacturer in
Fuel Cell Standards Committee
This document seeks to classify all-wheel drive (AWD) architectures primarily based on the installed hardware and does not consider the implementation of the controls and software. For example, a power transfer unit (PTU) may be equipped with a clutch that is capable of torque management, but the control implementation only uses it for disconnection functions without torque management. In this SAE Recommended Practice, attention will be given to passenger cars and light trucks (through Class III). The definitions presented herein may also be applicable to heavy trucks (Class 4 through 8) and off-highway applications using more than two axles but are primarily focused on passenger cars and light trucks
Drivetrain Standards Committee
This SAE Recommended Practice provides test methods and criteria for evaluating the internal cleanliness and air leakage for engine charge air coolers. This SAE Recommended Practice also provides nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air cooling system operational performance parameters
Cooling Systems Standards Committee
9100 품질관리시스템 내 AQAP 2110 적용에 관한 지침IA9137_KOKR (Current)02/16/2024
이 문서는 공급자가 9100의 조항을 준수하고자 할 때 AQAP-2110을 적용하는 것에 관한 정보와 지침을 제공하기 위해 작성 및 발행된 것이다. 이 문서는 AQAP-2110-SRD.2 및 IA9137로 간행된다. 이는 NATO와 산업계에서 AQAP-2110과 9100 간의 관계에 대한 이해와 활용을 촉진하기 위해 NATO와 산업계 대표들이 공동으로 작성한 것이다. 획득 국가가 자국의 조달 방법으로 대외군사판매(FMS)를 이용할 때는 AQAP가 필요할 수 있다. 이 문서는 획득 국가와 9100을 준수하고자 하는 공급 국가의 AQAP-2110 요구사항 해석에 있어 공통성을 제공하는 데에 목적을 두고 있다. 이 문서의 내용은 법적 또는 계약상의 지위를 갖지 않으며, 일체의 AQAP-2110 또는 9100 요구사항을 대체하거나 그 요구사항에 추가되는 것도 아니다. 있을 수 있는 조건의 다양성(작업 또는 공정의 유형, 사용 기기 및 관련 인원의 역량에 따르는) 때문에, 이 지침이 모든 것에 적용되는 것으로 간주하거나, 계약 요구사항 충족에 필요한 특정 수단 또는 방법을 강요하는 것으로 간주해서는 안 된다. 이해당사자들은 이러한 요구사항을 충족하기 위해 다른 수단 또는 방법을 사용할 수도 있다는 점을 알고 있어야 한다. 이 지침 사용자는 계약서에 명시되는 바와 같이 AQAP 2110 요구사항이 공급자와 하청업체가 지켜야 하는 의무사항임을 명심해야 한다
IAQG-1 Standards Committee
This SAE Recommended Practice defines the minimum performance and dimensional requirements for quick connect couplings between flexible tubing or hose and rigid tubing or tubular fittings used in coolant systems. This document applies to automotive and light duty truck applications under the following conditions: a Gasoline, diesel, hybrid, and electrical propulsion cooling systems. b Operating pressure up to 206 kPa (30 psi). c Operating temperatures from -40 °C (-40 °F) to 125 °C (260 °F). Quick connect couplings function by joining the connector to a mating end form, typically without the use of tools. The requirements stated in this document apply to new connectors in assembly operations unless otherwise indicated. For modern powertrain applications, the interconnection of the following devices is typically the design responsibility of the cooling group: coolant control valve, water-to-air charge air cooler (CAC), radiator (high and low temperature variants), and remote
Cooling Systems Standards Committee
This document derives from the Federal Motor Vehicle Safety Standards (FMVSS) 105 and 135 vehicle test protocols as single-ended inertia-dynamometer test procedures. The test sequences enable brake output measurement, friction material effectiveness, and corner performance in a controlled and repeatable environment. This SAE Document also includes optional sections for parking brake output performance for rear brakes with hydraulic or Electric Park Brakes (EPB). It applies to brake corners from vehicles covered by the FMVSS 105 and 135 when using the appropriate brake hardware and test parameters. The FMVSS 135 applies to all passenger cars and light trucks up to 3500 kg of gross vehicle weight (GVWR). The FMVSS 105 applies to all passenger cars, multi-purpose vehicles, buses, and trucks above 3500 kg of GVWR. This document does not include testing for school bus applications or vehicles equipped with hydraulic brakes with a GVWR above 4540 kg. This document does not evaluate or
Brake Dynamometer Standards Committee
To harmonize and define terminology associated with occupant protection for children for vehicle manufacturers and child restraint manufacturers in the United States and Canada
Children's Restraint Systems Committee
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light trucks having gross vehicle weight rating (GVWR) of 4540 kg (10 000 lb) or less. The test procedure is characterized by having fixed initial conditions (specified initial vehicle speed and gear selection at the starting point on the test site) to obtain vehicle interior sound measurement during road load operation over various road surfaces at specified constant speeds. The measurement data so derived is useful for vehicle engineering development and analysis
Light Vehicle Exterior Sound Level Standards Committee
THIS STANDARD ESTABLISHES THE DIMENSIONAL AND VISUAL QUALITY REQUIREMENTS, LOT REQUIREMENTS, AND PACKAGING AND LABELING REQUIREMENTS FOR O-RINGS MOLDED FROM AMS7410 FLUOROCARBON (FKM) RUBBER. IT SHALL BE USED FOR PROCUREMENT PURPOSES
A-6C2 Seals Committee
This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life. The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents. However, when the requirements of this document are in conflict with the customer's requirements or specifications, the requirements of the customer's detailed specification
A-6C2 Seals Committee
This SAE Aerospace Standard (AS) specifies the dimensions, tolerances and size codes (dash numbers) for O-rings with a larger cross-section than those to AS568, for use in glands per MIL-G-5514 where squeeze at low temperature is often insufficient to provide a leak-tight seal
A-6C2 Seals Committee
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for back-up rings machined from AMS3678/1 polytetrafluoroethylene materials for use in AS5202 ports. It shall be used for procurement purposes
A-6C2 Seals Committee
There is no ISO standard equivalent to this SAE Standard. This SAE Standard identifies and defines the most commonly used terms for piston ring-groove characteristics, specifies dimensioning for groove widths, and demonstrates the methodology for calculation of piston groove root diameter. The requirements of this document apply to pistons and rings of reciprocating internal combustion engines and compressors working under analogous conditions, up to and including 200 mm diameter and 4.5 mm width for compression rings and 8.0 mm width for oil rings. The specifications in this document assume that components are measured at an ambient temperature of 20 °C (68 °F). Tolerances specified in this document represent practical functional limits and do not imply process capabilities
Piston and Ring Standards Committee
This SAE Recommended Practice covers the requirements for ethernet physical layer (PHY) qualification (and as applicable to other high-speed networks [i.e., Audio Bus, LVDS, Ser-Des, etc.]). Requirements stated in this document provide a minimum standard level of performance for the PHY in the IC to which all compatible ethernet communications PHY shall be designed. When the communications chipset is an ethernet switch with an integrated automotive PHY (xBASE-T1), then the testing shall include performance for all switch PHY ports as well as each controller interface. No other features in the IC are tested or qualified as part of this SAE Recommended Practice. This assures robust serial data communication among all connected devices regardless of supplier. The goal of SAE J2962-3 is to commonize approval processes of ethernet PHYs across OEMs. The intended audience includes, but is not limited to, ethernet PHY suppliers, component release engineers, and vehicle system engineers
Vehicle Architecture For Data Communications Standards
This SAE Standard prescribes the procedure for making hardenability tests and recording results on shallow and medium hardening steels, but not deep hardening steels that will normally air harden. Included are procedures using the 25 mm (1 in) standard hardenability end-quench specimen for both medium and shallow hardening steels and subsize method for bars less than 32 mm (1-1/4 in) in diameter. Methods for determining case hardenability of carburized steels are given in SAE J1975. Any hardenability test made under other conditions than those given in this document will not be deemed standard and will be subject to agreement between supplier and user. Whenever check tests are made, all laboratories concerned must arrange to use the same alternate procedure with reference to test specimen and method of grinding for hardness testing. For routine testing of the hardenability of successive heats of steel required to have hardenability within certain limits, it is sufficient to designate
Metals Technical Committee
This test code describes tests for determining characteristics of hydraulic positive displacement pumps used on off-road self-propelled work machines as referenced in SAE J1116
CTTC C1, Hydraulic Systems
To determine the ability of a fuel/water separator to separate emulsified or finely dispersed water from fuels. This test method is applicable for biodiesel fuel
Filter Test Methods Standards Committee
This SAE Aerospace Standard (AS) specifies scarf-cut polytetrafluoroethylene (PTFE) retainers (backup rings) for use in glands in accordance with AS4716. They are usually used in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with O-rings and other seals for static and dynamic applications. NOTE: This specification includes material tests but does not include hydraulic or pneumatic performance tests
A-6C2 Seals Committee
Items per page:
1 – 50 of 210997