Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of castings (see 8.6).
This specification covers an aluminum alloy in the form of castings.
This specification covers a titanium alloy in the form of welding wire (see 8.5).
It is recommended that all helicopter engine development programs include an evaluation of engine starting requirements. The evaluation should include starting requirement effects on helicopter weight, cost, and mission effectiveness. The evaluation should be appropriate to the engine stage of development.
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers the requirements for an electroless nickel-thallium-boron or nickel-boron deposit on various substrates.
SAE J1978-1 specifies a complementary set of functions to be provided by an OBD-II scan tool. These functions provide complete, efficient, and safe access to all regulated OBD (on-board diagnostic) services on any vehicle which complies to SAE J1979. The content of this document is intended to satisfy the requirements of an OBD-II scan tool as required by current U.S. OBD regulations. This document specifies: A means of establishing communications between an OBD-equipped vehicle and an OBD-II scan tool. A set of diagnostic services to be provided by an OBD-II scan tool in order to exercise the services defined in SAE J1979. In addition, SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 plus automatic protocol determination for all SAE J1979/J1979-2/J1979-3 application content. The presentation of the SAE J1978 document family, where SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 and protocol determination for SAE J1979, SAE
This specification covers flash-welded rings made of titanium and titanium alloys (see 8.5).
This specification covers a titanium alloy in the form of sheet 0.020 to 0.1874 inch (0.51 to 4.760 mm), inclusive, in nominal thickness (see 8.6).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to and including 1.000 inch (25.4 mm) in diameter, least thickness, or tube wall thickness (see 8.6).
This SAE Standard applies to machines as defined in Appendix A. Some of these machines can travel on-highway but function primarily off-highway.
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to AS85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire, along with recommended harnessing methods and techniques, are also presented.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification covers an aluminum alloy in the form of bars and rods 0.500 to 8.000 inches (12.7 to 203.2 mm) in nominal diameter or least difference between parallel sides and up to 50 square inches (322.6 cm2) in cross-sectional area (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of investment castings.
This specification covers an aluminum alloy in the form of sand castings (see 8.6).
This specification covers a titanium alloy in the form of sheet 0.025 through 0.100 inch (0.63 through 2.54 mm), inclusive, in thickness (see 8.6).
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Recommended Practice summarizes the conformance requirements for digital communication between the PEV and EVSE and establishes the interoperability requirements for successful charging sessions. This first version includes charging conformance summary for both the vehicle and EVSE and updates from CharIN with modifications, additions, and deletions to improve successful charging sessions. The summary of all existing charging/discharging standards, conformance, and functional categories will be updated in subsequent updates, and message/signal/values that would cause an interoperability issue will be clarified as this leads to diagnostic codes the vehicle/EVSE/Charge Point Operator and others can view to let the customer know what specific issue led to a failure to charge or discharge. This additional effort is ongoing and will be expanded in the next version update as this becomes more mature.
These Protocols can be used for all forms of motorsports; however, only certain combinations of Green Racing Elements will result in motorsport competitions that are recognized as Green Racing events. As new information, fuels and technologies emerge, addendums or new protocols will be developed. The SAE International (SAE) Motorsports Engineering Activity is also an invaluable source of reference materials and ongoing technical advice providing access to the constantly evolving set of best safety and operational practices for current and emerging technologies. This is especially true with regard to high voltage safety and the adoption of other advanced propulsion and fuel system technologies.
This SAE Information Report is the listing of recommendations for the proper packaging, storage, and shelf life limitations of new and unused hydraulic brake hose assemblies. The document embodies the testing, analysis, and experience of many users and manufacturers. Where specific manufacturer's recommendations are made, those recommendations shall supersede the recommendations of this document. This document describes the successful procedures and practices associated with brake hose assemblies usage by a wide cross section of manufacturers and users over several years. The practices are expected to be applicable to all brake hose assemblies which qualify under SAE J1401.
This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.
This document will apply to the most common applications of electric motors, used for activating all-wheel drive (AWD) and four-wheel drive (4WD) disconnect systems as used in passenger (car and light truck) vehicles. The standard will provide consistent definition, terminology, tests, and reporting methods.
To establish the acceptance criteria for discontinuities as revealed by magnetic particle or liquid penetrant examination of aircraft utility parts as in 1.2.
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
This specification covers corrosion preventive compounds for spray application to vehicle body cavities
This SAE Aerospace Standard provides minimum design, installation, and removal requirements for AS3319 through AS3322 studs and is applicable when specified on engineering drawings, or in procurement documents.
Items per page:
50
1 – 50 of 216126