Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Recommended Practice applies to functions of motor vehicle signalling and marking lighting devices which use light emitting diodes (L.E.D.’s) as light sources. This report provides test methods, requirements, and guidelines applicable to the special characteristics of L.E.D. lighting devices. This Recommended Practice is in addition to those required for devices designed with incandescent light sources. This report is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
This document addresses robustness of electrical/electronic modules for use in automotive applications. Where practical, methods of extrinsic reliability detection and prevention will also be addressed. This document primarily deals with electrical/electronic modules (EEMs), but can easily be adapted for use on mechatronics, sensors, actuators and switches. EEM qualification is the main scope of this document. Other procedures addressing random failures are specifically addressed in the CPI (Component Process Interaction) section 10. This document is to be used within the context of the Zero Defect concept for component manufacturing and product use. It is recommended that the robustness of semiconductor devices and other components used in the EEM be assured using SAE J1879 OCT2007, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications. The emphasis of this document is on hardware and manufacturing failure mechanisms, however, other contemporary issues
This standard covers low voltage primary cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
This engineering design specification provides design parameters and general requirements for School Bus Stop Arms equipped with alternately flashing lights. The stop arm is intended as an optional device which may be used in addition to, but not as a substitute for, school bus signal lamps covered by SAE J887(July, 1964). Decision for adoption of the recommendations presented in the Appendix is left to governmental units or other bodies who adopt this practice.
This SAE Standard provides requirements and test procedures for the daytime running light function (DRLF) and the lamps that provide it.
This document provides design guidelines, test procedure references, and performance requirements for omnidirectional and selective coverage optical warning devices used on authorized emergency, maintenance, and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
This SAE Standard provides test procedures and performance requirements for off-highway vehicle headlamps.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for backup/reversing lamps.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines—Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
SCOPE IS NOT AVAILABLE.
This specification covers two types of thickened, water base temporary coating remover in the form of an alkaline liquid.
This SAE Recommended Practice provides for common test and verification methods to determine lead acid and nickel metal hydride electric vehicle battery module performance. The document creates the necessary performance tests to determine (a) what the basic performance of EV battery modules is, and (b) if battery modules meet minimum performance specification established by vehicle manufacturers or other purchasers. Specific values for these minimum performance specifications are not a part of this document.
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU. It further specifies additional
This Technical Information Report defines the diagnostic communication protocol Keyword Protocol 1281 (KWP1281). This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECUs, in which a KWP1281 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the KWP1281 protocol in enough detail to support the requirements necessary to implement the communication protocol in an SAE J2534 interface device.
This Technical Information Report defines the proprietary diagnostic communication protocol for ABS or VSA ECU (Electronic Control Unit) implemented on some Honda vehicles. This protocol does not apply to all Honda vehicles. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an enhanced SAE J2534 interface. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an enhanced SAE J2534 interface.
This document is intended to define the standardized Diagnostic Trouble Codes (DTCs) that On-Board Diagnostic (OBD) systems in vehicles are required to report when malfunctions are detected. SAE J2012 may also be used for decoding of enhanced diagnostic DTCs and specifies the ranges reserved for vehicle manufacturer specific usage.
This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On-and OffRoad Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation. Although devices may be
This SAE Recommended Practice applies to motor vehicle forward illumination systems and subsystems generated by discharge sources. It provides test methods, requirements, and guidelines applicable to the special characteristics of gaseous discharge lighting devices which supplement those required for forward illumination systems using incandescent light sources. The document is applicable to both discharge forward lighting systems, subsystems and components. This document is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
This SAE Recommended Practice describes a standardized interface that connects between a standard personal computer (PC) and vehicle. The purpose of this interface is to enable the reprogramming of emission-related control modules, in 2004 and later model year vehicles. The interface shall consist of the necessary hardware and/or software to support the requirements defined in this document. It is expected that vehicle manufacturers will provide the software application that will control the Pass-Thru Interface, to perform the actual reprogramming. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with interface supplied by any tool manufacturer. A common interface for all vehicle manufacturers reduces the tool costs for aftermarket garages, while allowing each vehicle manufacturer to control the programming sequence for the electronic control units (ECUs) in their vehicles. Aftermarket garages will be able to obtain a
This SAE Standard provides requirements, test procedures, and installation guidelines for clearance, sidemarker, and identification lamps intended for use on vehicles 2032 mm or more in overall width. Sidemarker lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width.
This SAE Recommended Practice provides procedures and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than, equal to, or greater than 2032 mm in overall width.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for side turn signal lamps intended for use on vehicles 12 m or more in overall length, except pole trailers. Side turn signal lamps conforming to the requirements of this document may be used on other large vehicles such as trucks, truck tractors, buses, and other applications where this type of lighting device is desirable. It is not intended for use on shorter vehicles due to the higher intensity requirements of SAE J2039 compared to the SAE J914 devices.
This document provides design guidelines, test procedure references, and performance requirements for directional, single color, flashing optical warning devices used on authorized emergency, maintenance, and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
This SAE Standard provides the minimum requirements for primary and auxiliary jumper cable plug and receptacle for the truck-trailer and converter dolly jumper cable systems for 12 VDC nominal applications. It includes the test procedures, design, and performance requirements.
This SAE Standard describes snowmobile and snowmobile cutter requirements for the installation of lamps, reflective devices, and associated equipment.
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cleaners intended for use on motor vehicles.
This SAE Recommended Practice applies to motor vehicle signaling and marking devices which use light generated by a discharge source. This document provides test methods, requirements, and guidelines applicable to the unique characteristics of discharge lighting systems and their components. These are in addition to those required for signal and marking devices. This document is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cargo lamps intended for use on vehicles under 5443 kg (12000 pounds) Gross Vehicle Weight Rating (GVWR).
This SAE Standard covers unshielded cable, 22 gauge and larger, intended for use at a nominal system voltage up to 600 V or 1000 V (ACrms or DC). It is intended for use in surface vehicle electrical systems.
This SAE Recommended Practice applies to retroreflective sheeting materials that are used on truck tractors and trailers 2032 mm or more in overall width and with a gross vehicle weight rating (GVWR) over 4536 kg and school buses to improve vehicle conspicuity. The retroreflective sheeting materials for the truck tractors and trailers are super-high-intensity materials containing microprisms. The retroreflective sheeting materials for school buses may contain flexible non-exposed glass bead lenses or microprisms.
This SAE Standard outlines general procedures for the grounding of electrical components in 12- and 24-V systems, intended for light and heavy-duty on-highway trucks and their trailers; and off-road machinery applications as described in SAE J1116.
The purpose of this document is to provide performance requirements for hydrogen dispensing systems used for fueling 35 MPa heavy duty hydrogen transit buses and vehicles (other pressures are optional). This document establishes the boundary conditions for safe heavy duty hydrogen surface vehicle fueling, such as safety limits and performance requirements for gaseous hydrogen fuel dispensers used to fuel hydrogen transit buses. For fueling light-duty vehicles SAE J2601 should be used. SAE J2601-2 is a performance based protocol document that also provides guidance to fueling system builders, manufacturers of gaseous hydrogen powered heavy duty transit buses, and operators of the hydrogen powered vehicle fleet(s). This fueling protocol is suitable for heavy duty vehicles with a combined vehicle CHSS capacity larger than 10 kilograms aiming to support all practical capacities of transit buses. It is non-prescriptive in how to achieve a full fill or 100% state of charge (SOC) in the
This SAE Standard describes alternator physical, performance, and application requirements for heavy-duty electrical charging systems for off-road work machines, including those defined in SAE J1116.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Recommended Practice is intended to describe the application of single-phase DC to AC inverters, and bidirectional inverter/chargers, which supply power to ac loads in Class heavy duty on-highway trucks (10K GVW). The document identifies appropriate operating performance requirements and adds some insight into inverter selection. This document applies to factory and after-market installed DC-to-AC inverter systems (Including inverter chargers) providing up 3000 W of 120 VAC line-voltage power as a convenience for operator and passenger use. Such inverters are intended to power user loads not essential to vehicle Operation or safety (e.g., HVAC, TV, microwave ovens, battery chargers for mobile phones or laptop computers, audio equipment, etc.). Systems incorporate the inverter itself as well as the input, output, control, and signal wiring associated with the inverter. Requirements are given for the performance, safety, reliability, and environmental compatibility of the system
SAE J2601-4 establishes process limits for ambient temperature hydrogen fueling of light-duty automotive vehicles, passenger cars, and trucks that use a compressed hydrogen storage system (CHSS) that meets SAE J2579, where ambient temperature hydrogen fueling is defined as a fueling event where the fuel delivery temperature is greater (e.g., warmer) than the precooled requirements of SAE J2601. Table 1 depicts the scope of SAE J2601-4 and potential work items for future revisions within this or other documents of the SAE J2601 series. SAE J2601 includes protocols that are applicable for two pressure classes (35 MPa and 70 MPa), three fuel delivery temperature categories (-40 °C, -30 °C, and -20 °C) and CHSS sizes from 49.7 to 248.6 L. Future versions of SAE J2601 may incorporate warmer fuel delivery temperatures (-10 °C and ambient) and smaller compressed hydrogen storage systems for motorcycles and other light-duty applications. Fueling protocols should be developed based on a set of
This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters NC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.
Items per page:
50
1 – 50 of 219487