Browse Topic: Brake seals
These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document
These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document
This SAE Recommended Practice was prepared by the Motor Vehicle Brake Fluids Subcommittee of the SAE Hydraulic Brake Actuating Systems Committee to provide engineers, designers, and manufacturers of motor vehicles with a set of minimum performance standards in order to assess the suitability of silicone and other low water tolerant type brake fluids (LWTF) for use in motor vehicle brake systems. These fluids are designed for use in braking systems fitted with rubber cups and seals made from natural rubber (NR), styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM). In the development of the recommended requirements and test procedures contained herein, it is concluded that the LWTFs must be functionally compatible with existing motor vehicle brake fluids conforming to SAE J1703 and with braking systems designed for such fluids. To utilize LWTFs to the fullest advantage, they should not be mixed with other brake fluids. Inadvertent mixtures of LWTFs
These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document
This recommended practice was prepared by the Motor Vehicle Brake Fluids Subcommittee of the SAE Hydraulic Brake Systems Actuating Committee to provide engineers, designers, and manufacturers of motor vehicles with a set of minimum performance standards in order to assess the suitability of silicone and other low water tolerant type brake fluids (LWTF) for use in motor vehicle brake systems. These fluids are designed for use in braking systems fitted with rubber cups and seals made from natural rubber (NR), styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM). In the development of the recommended requirements and test procedures contained herein, it is concluded that the LWTF's must be functionally compatible with existing motor vehicle brake fluids conforming to SAE Standard J1703 and with braking systems designed for such fluids. To utilize LWTF's to the fullest advantage, they should not be mixed with other brake fluids. Inadvertent mixtures of
This recommended practice was prepared by the Motor Vehicle Brake Fluids Subcommittee of the SAE Hydraulic Brake Systems Actuating Committee to provide engineers, designers, and manufacturers of motor vehicles with a set of minimum performance standards in order to assess the suitability of silicone and other low water tolerant type brake fluids (LWTF) for use in motor vehicle brake systems. These fluids are designed for use in braking systems fitted with rubber cups and seals made from natural rubber (NR), styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM). In the development of the recommended requirements and test procedures contained herein, it is concluded that the LWTF’s must be functionally compatible with existing motor vehicle brake fluids conforming to SAE Standard J1703 and with braking systems designed for such fluids. To utilize LWTF’s to the fullest advantage, they should not be mixed with other brake fluids. Inadvertent mixtures of
Items per page:
50
1 – 7 of 7