Results
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
This specification covers the installation of aircraft interior lighting for military aircraft.
This specification establishes the procedures used to produce a hard anodic coating on magnesium alloys and the properties of the coating.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This document provides recommendations to identify battery group sizes and dimensions for 6 V, 8 V, 12 V, and 24 V lead acid batteries.
This specification covers a manganese alloy in the form of powder, preforms, and a viscous mixture (paste) of the powder in a suitable binder.
This FMEA standard describes potential failure mode and effects analysis in design (DFMEA), supplemental FMEA-MSR, and potential failure mode and effects analysis in manufacturing and assembly processes (PFMEA). It assists users in the identification and mitigation of risk by providing appropriate terms, requirements, rating charts, and worksheets. As a standard, this document contains requirements—”must”—and recommendations—”should”—to guide the user through the FMEA process. The FMEA process and documentation must comply with this standard as well as any corporate policy concerning this standard. Documented rationale and agreement with the customer are necessary for deviations in order to justify new work or changed methods during customer or third-party audit reviews.
This standard outlines test methods and practices which can detect embrittlement of steel parts. It is a process control or referee verification test. The risk of embrittlement of steel is minimized by using best practices in the finishing/coating process. One such practice is described in SAE/USCAR-5, Avoidance of Hydrogen Embrittlement of Steel.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers a corrosion-resistant steel in the form of two types of aircraft tubing.
This SAE Aerospace Standard (AS) establishes a Generic Open Architecture (GOA) Framework for application independent hardware/software systems. This document defines the interface classes for the GOA Framework. Supplemental documents define the guidelines for applying the GOA Framework to specific applications.
Communicate the process of accurately measuring sound power levels of positive displacement hydraulic pumps commonly used in ground vehicle steering systems. This recommended practice defines the pump mounting (pulley, belt tension, isolation), operating conditions (fluid, speed, temperature, pressure), room acoustics, instrumentation, noise measurement technique and data acquisition setup to be used. Included are recommendations for test sample size, and format for data presentation/reporting.
This SAE Aerospace Standard (AS) covers the general requirements for the design, manufacture, and test of 28 VDC, 270 VDC, and 115 VAC solid-state power controllers (SSPCs) for use in electrical power systems. SSPCs conforming to this standard are intended for use in controlling the making and breaking of power circuits for electrically operated equipment and devices, and for providing overload and short-circuit protection. Applications that require SSPCs to have a high level of performance in some areas or may be exposed to harsher electrical or environmental conditions are designated as CLASS A. Applications that utilize SSPCs in moderate level of performance or are exposed to a controlled environment are designated as CLASS C. Applicability of both MIL-STD-704 and RTCA DO-160G have been considered when determining the performance standards for the designated classes of SSPCs. To support older aircraft platforms, legacy versions of these specifications were also considered as
XRF technique for counterfeit detection is applicable to electrical, electronic and electromechanical (EEE) parts as listed in AS6171 General Requirements. In general, the detection technique is meant for use on piece parts prior to assembly on a circuit board or on the parts that are removed from a circuit board. The applicability spans a large swath of active, passive and electromechanical parts. If AS6171/3 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
This SAE Recommended Practice provides a taxonomy of terms related to local and regional on-demand and shared mobility services (including ground, aviation, and maritime) and their enabling technologies. Functional definitions for shared modes (both fleet sharing and ride services), services, business models, and mobility applications are defined in this SAE Recommended Practice. This SAE Recommended Practice also provides a taxonomy of related terms and definitions. Though public transport is part of shared mobility, it is not included in this SAE Recommended Practice because its definition is well-established and documented. This document does not provide specifications or otherwise impose requirements on on-demand and shared mobility.
This specification covers a corrosion and heat resistant nickel alloy in the form of sheet and strip.
This SAE Standard establishes the requirement for suppliers to plan a maintainability program that satisfies the following three requirements: The supplier shall ascertain customer requirements. The supplier shall meet customer requirements. The supplier shall assure that customer requirements have been met.
This SAE Aerospace Recommended Practice (ARP) defines impulse test procedures that are recommended for hydraulic components.
The recommended practice describes a design standard that defines the maximum recommended voltage drop of the starting motor main circuits, as well as control system circuits, for 12/24-V starter systems. The battery technologies used in developing this document include the flooded lead acid, gel cell, and AGM. Starting systems supported by NiCd, Lithium Ion, NiZn, etc., or Ultracaps are not included in this document. This document is not intended to be updated or modified to include starter motors rated at voltages above the nominal 24-V electrical system. The starter is basically an electrical-to-mechanical power converter. If you double the available battery power in, you double the peak mechanical power out and double the heat losses. This means that we have to pay special attention to how battery power changes when we change the battery voltage and the effects it may have in overpowering the cranking system. A new stand-alone document would need to be developed to address
This SAE Aerospace Standard (AS) defines the requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in 400 °F, 3000 psi aircraft hydraulic systems. Assemblies are suitable where rapid rate pressure pulsing and torsional/ longitudinal flexing may occur, in addition to normal hydraulic system loads.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
The following system of symbols is recommended for use in technical papers and engineering reports dealing with hydrodynamic drives.
This SAE Aerospace Recommended Practice (ARP) covers visible surface defects on aerospace hose assemblies which have been installed and are functioning within a working environment at the time of visual inspection.
This specification presents requirements for thin-walled (inside diameter greater than four times the wall thickness and outside diameter 1/4 inch and larger) corrosion-resistant steel tubing in approximately the 1/8 hard condition, of special quality, suitable for use in high-pressure hydraulic systems.
This test method outlines the recommended procedure for performing dimensional stability tests on rolling element bearings used in airframe applications. Bearings covered by this document shall be antifriction ball bearings and spherical roller bearings with through-hardened outer rings.
This SAE Aerospace Information Report (AIR) applies to landing gear tires and airframe structure for all types and models of civil and military aircraft having tires as part of the landing gear.
This standard covers self-propelled off-road work machines as categorized in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
Items per page:
50
1 – 50 of 222094