Search
Advanced Search
of the following are true

Results

Items (207,320)
This document provides background information, rationale, and data (both physical testing and computer simulations) used in defining the component test methods and similarity criteria described in SAE Aerospace Recommended Practice (ARP) 6330. ARP6330 defines multiple test methods used to assess the effect of seat back mounted IFE monitor changes on blunt trauma to the head and post-impact sharp edge generation. The data generated is based on seat and IFE components installed on type A-T (transport airplane) certified aircraft. While not within the scope of ARP6330, generated test data for the possible future development of surrogate target evaluation methods is also included
Aircraft Seat Committee
This SAE Aerospace Recommended Practice (ARP) provides recommendations for: The audit process in general A list of specific areas of attention to be audited Maintaining the test facility in such a manner that it meets audit requirements
EG-1E Gas Turbine Test Facilities and Equipment
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft
Marine Technical Steering Committee
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
AMS E Carbon and Low Alloy Steels Committee
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder
AMS D Nonferrous Alloys Committee
This specification details requirements and procedures for the detection of defects in aircraft structural and engine components during maintenance and overhaul operations
AMS K Non Destructive Methods and Processes Committee
This specification covers a gold-palladium-nickel alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, chips, preforms and a viscous mixture (paste) of the powder in a suitable binder
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a corrosion and heat resistant steel in the form of bars, forgings, and forging stock
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers an aluminum alloy procured in the form of extruded profiles (shapes) with cross-sections up to 7.75 square inches (5000 mm2
AMS D Nonferrous Alloys Committee
This specification covers a titanium alloy in the form of prealloyed powder
AMS G Titanium and Refractory Metals Committee
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
Engine Power Test Code Committee
This specification covers the procedure for applying a disilicide diffusion coating to molybdenum and molybdenum alloy parts by the pack cementation method and the properties of the coating so deposited
AMS B Finishes Processes and Fluids Committee
This specification covers one weight and one weave of novoloid/aramid cloth
AMS P Polymeric Materials Committee
This specification covers one width and one breaking strength of low-modulus aramid webbing
AMS P Polymeric Materials Committee
This specification covers a corrosion and heat-resistant nickel alloy in the form of welding wire
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a centrifugally-cast, alloyed iron in the form of sleeves for the fabrication of piston rings
AMS E Carbon and Low Alloy Steels Committee
This specification covers the requirements for embrittlement relief (baking) of heat treated steel parts to remove hydrogen infused during plating and certain other chemical processing such as stripping, chemical milling, pickling, and etching
AMS B Finishes Processes and Fluids Committee
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet
AMS P17 Polymer Matrix Composites Committee
This specification covers a corrosion and heat resistant nickel alloy in the form of sand castings
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a corrosion and heat resistant steel in the form of bars, wire, and forgings 7.0 inches (178 mm) and under in nominal diameter or least distance between parallel sides, and forging stock of any size (see 8.6
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a polytetrafluoroethylene (PTFE) resin filled with inorganic pigment in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process
AMS P Polymeric Materials Committee
This specification covers one width and one breaking strength of low modulus aramid tubular webbing
AMS P Polymeric Materials Committee
This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles (shapes) with a maximum cross-sectional area of 25 in2 (161 cm2), a maximum circle size of 12 inches (305 mm) and a nominal thickness up to 3.250 inch (82.54 mm), inclusive
AMS D Nonferrous Alloys Committee
This specification covers the specific requirements for aluminum alloy 7178-T76 bar, rod, shapes, and wire produced by extrusion
AMS D Nonferrous Alloys Committee
This specification covers one width and one breaking strength of low-modulus aramid webbing
AMS P Polymeric Materials Committee
This specification covers the specific requirements for improved exfoliation resistant alclad aluminum alloy 7178-T76 sheet and -T7651 plate. The general requirements are covered in AMS-QQ-A-250. The plate and sheet covered by this specification shall be an integral composite product consisting of a heat-treatable aluminum alloy (7178) core with thin layers of an aluminum alloy (7072) anodic to the core and of approximately equal thickness, bonded to both surfaces
AMS D Nonferrous Alloys Committee
This specification covers a corrosion-resistant steel in the form of sheet, strip, and foil 0.005 inch (0.13 mm) and over in nominal thickness (see 8.4
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a phosphonitrilic fluoroelastomer (FZ) in the form of molded rings. Primarily for use in aircraft fuels systems operating from -55 to +150 degrees C (-67 to 302 degrees F
AMS CE Elastomers Committee
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet
AMS P17 Polymer Matrix Composites Committee
This specification covers the requirements for a refined paraffinic petroleum-base lubricant
AMS B Finishes Processes and Fluids Committee
This specification covers the engineering requirements for producing a thin tin coating on aluminum alloys by an immersion process
AMS B Finishes Processes and Fluids Committee
This specification covers thermal radiation resistant material in the form of tape with pressure-sensitive adhesive
AMS P Polymeric Materials Committee
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet
AMS P17 Polymer Matrix Composites Committee
This specification establishes the requirements for a general-purpose brush plating of nickel applied by electrodeposition
AMS B Finishes Processes and Fluids Committee
This specification covers the specific requirements for aluminum alloy 5083 bar, rod, shapes, tube, and wire produced by extrusion
AMS D Nonferrous Alloys Committee
This specification covers one type of glass cloth impregnated with a heat-reactive, thermosetting, hot-melt, addition-type, polyimide resin system, furnished in continuous rolls of full width material
AMS P17 Polymer Matrix Composites Committee
This specification covers cabled-strand ropes formed from impregnated aramid fibers
AMS P Polymeric Materials Committee
This specification covers a magnetic nickel-iron alloy in the form of sheet and strip
AMS E Carbon and Low Alloy Steels Committee
This specification covers an aluminum alloy in the form of permanent mold castings
AMS D Nonferrous Alloys Committee
This specification covers the procedures for approval of products of premium-quality titanium alloys and the controls to be exercised in producing such products
AMS G Titanium and Refractory Metals Committee
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for annealing of austenitic corrosion-resistant steel parts. Parts are defined in AMS2759. General ordering instructions are specified in AMS2759
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a corrosion-resistant steel in the form of laminated sheet
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a corrosion and heat resistant steel in the form of forgings, wire, bars, and mechanical tubing, flash welded rings, and stock of any size for forging or flash welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
AMS E Carbon and Low Alloy Steels Committee
This document describes a systematic and rigorous process to: (1) identify and evaluate standard names and definitions for driving automation system features, and (2) identify a “user vocabulary” of terms and descriptions that [human] drivers use to describe driving automation system features. The process described in this document includes selection criteria and trade-offs that can be used to select an approach to testing that matches the constraints and objective of a particular evaluation. The data from this process are analyzed to determine users’ name preferences for driving automation system features and what they would expect a specific feature to do, based on the name given to the features. The data generated by this naming methodology can provide guidance regarding the names that may support accurate understanding of the feature’s capabilities and limitations. Although the process described in this document emphasizes the use of large-scale electronic surveys for data
null, null
This specification covers a corrosion and heat resistant steel in the form of welded tubing
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers the requirements for surface metal removal of ferrous and non-ferrous metals by milling processes using controlled immersion of parts in chemical etching solutions
AMS B Finishes Processes and Fluids Committee
This specification covers one type of organic (para-aramid) fiber in the form of roving. The product shall be formed as a number of ends, tows, or strands collected into a parallel bundle with little or no twist
AMS P17 Polymer Matrix Composites Committee
Items per page:
1 – 50 of 207320