Results
This SAE Aerospace Standard (AS) defines minimum standards of design, construction, and performance for two types of permanently installed, high pressure 12,800 kPa (1850 psig) and 13,800 kPa (2000 psig) oxygen system cylinder fill valves used in commercial aircraft. Refer to Purchaser's Specification for Requirements which are beyond the scope or level of detail provided in this document. One valve has an adjustable pressure sensitive closing valve to automatically control the final pressure for a correct amount of oxygen in the system. The second valve incorporates an automatic shutoff feature designed to limit system overpressurization in the event maintenance personnel do not stop system filling at the correct pressure. The intent of the fill valves is to control the rate of fill to limit the rise in temperature caused by compression heating to acceptable values, prevent oxygen back flow and prevent the ingestion of foreign matter that could cause contamination of the system. Note
Orientation of the engine, engine axis and coordinate system referred to herein shall be the conventional terminology used in all references to aircraft gas turbine engines
This procurement specification covers tubular sealing rings, commonly named METAL O-RING GASKETS, made from a corrosion and heat resistant steel tubing of the type identified under the Unified Numbering System as UNS S32100
This glossary provides accepted definitions for terms commonly used by manufacturers and users of electric wire and cable, and their components, intended for use on aerospace vehicles
This SAE Aerospace Information Report (AIR) presents flexure fatigue strength of tube fitting joints in the form of graphs showing applied deflection D and total calculated axial stress S versus number of cycles to failure N. The graphs have been prepared from data obtained by actual testing conducted in accordance with ARP1185
The scope of this SAE Aerospace Information Report (AIR) is to define recommended methods of determining the optimal dimensional relationship of components coupled together using thrust wires for applications such as coupling nuts and fittings. These design parameters are intended to optimize component loading characteristics and maximize wire shear capabilities for both high and low pressure applications
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries, and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses
This SAE Aerospace Standard (AS) establishes the characteristics and utilization of 270 V DC electric power at the utilization equipment interface and the constraints of the utilization equipment based on practical experience. These characteristics shall be applicable for both airborne and ground support power systems. This document also defines the related distribution and installation considerations. Utilization equipment designed for a specific application may not deviate from these requirements without the approval of the procuring activity
This document is offered to provide state-of-the-art information about design factors that must be considered in the design of new or significantly modified engine test cells used to test propeller equipped turboprop engines in either QEC or bare engine configurations. The report does not address design considerations for test cells designed to test turboprop engines with dynamometer type load absorption devices because they are essentially tested as turboshaft engines. Design considerations for those test cells are presented in AIR4989, Reference 2.1
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process
This SAE Aerospace Recommended Practice (ARP) establishes safety recommendations for lavatories in transport category airplanes
The SAE Aerospace Standard document AS681 is the parent document of this SAE Aerospace Recommended Practice (ARP). AS681 applies to Engine programs written to conform to this document. This ARP specifies a set of functions and their expected behaviors that constitute a function based Application Program Interface (API) for gas turbine engine customer programs. The functions specified in this API are delivered by the Supplier as part of the Engine model. This document defines generic language independent functions and specific appendices for implementations in C and Fortran. The function based API specified in this ARP represents an alternative to the Fortran COMMON block structure, as specified in AS4191, historically used to communicate with an engine program. The customer may request emulation of the AS4191 interface if desired. This document does not specify how the parameter names in the Engine program are constructed, how program capabilities might be expanded or altered, or how
This SAE Aerospace Information Report (AIR) includes general information about the various types and styles of flexible tanks and the tank-mounted fittings that adapt the tank to the surrounding structure and fluid-system plumbing. Recommendations are given relative to the dimensional layout of the tank when these recommendations serve to avoid tank fabrication problems and tank/structure interface problems. As a part of these recommendations, critical dimensions of plumbing adapter fittings are discussed and recommendations made. Tank manufacturing tolerances are given. Recommendations are made relative to cavity design and preparation to facilitate a reliable installation. The special installation requirements of nonself-sealing, self-sealing, and crash-resistant tanks are discussed. This document is not intended to replace the information or requirements of the military and commercial procurement specifications listed in Section 2. No attempt has been made, except in a very general
This recommended practice covers an instrument which measures and displays angle of deviation of the airstream dependent on mounting location on the aircraft
Items per page:
50
1 – 50 of 212620