Results
This specification defines the requirements for a grooved clamp coupling and flanges suitable for joining intermediate pressure and temperature ducting in aircraft air systems. The rigid coupling joint assembly, hereafter referred to as "the joint", shall operate within the temperature range of -65 °F to +800 °F
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4 inches (101.6 mm) (see 8.5
This specification covers polyvinyl chloride insulated single conductor electric wires made with tin-coated copper conductors or silver-coated copper alloy conductors. The polyvinyl chloride insulation of these wires may be used alone or in combination with other insulating or protective materials
This specification covers aluminum and aluminum alloy foil in the form of laminated sheet (see 8.6
This test code describes tests for determining characteristics of hydraulic positive displacement motors as used on off-road self-propelled work machines as referenced in SAE J1116
This specification covers a premium aircraft-quality corrosion-resistant steel in the form of bars, forgings, and forging stock
This test method provides a standardized procedure for evaluating the electrochemical resistance of automotive coolant hose and materials. Electrochemical degradation has been determined to be a major cause of EPDM coolant system hose failures. The test method consists of a procedure which induces voltage to a test specimen while it is exposed to a water/coolant solution. Method #1, referred to as a “Brabolyzer” test, is a whole hose test. Method #2, referred to as a “U” tube test, uses cured plate samples or plates prepared from tube material removed from hose (Method No. 2 is intended as a screening test only). Any test parameters other than those specified in this SAE Recommended Practice, are to be agreed to by the tester and the requester
This specification covers a silicone (MQ/VMQ/PVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be designated for use in molded O-rings and molded O-ring cord, molded rings, compression seals, molded-in-place gaskets, and plate seals for aeronautical and aerospace applications
This specification covers an aluminum alloy in the form of plate 0.250 to 5.500 inch (6.35 to 139.70 mm), inclusive, in nominal thickness (see 8.5
This SAE Aerospace Information Report (AIR) has been written for individuals associated with ground level testing of turbofan and turbojet engines and particularly for those who might be interested in investigating the performance characteristics of a new test cell design or of proposed modifications to an existing test cell by means of a scale model test
This specification covers a titanium alloy in the form of round bar and wire 0.625 inch (15.88 mm) and under in nominal diameter or thickness (see 8.7
This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm) in nominal diameter or least distance between parallel sides, inclusive, and maximum cross-sectional area of 32 square inches (206.5 cm2), forgings of thickness up through 4.000 inches (101.60 mm), inclusive, and maximum cross-sectional area of 32 square inches (206.5 cm2), and stock for forging of any size (see 8.6
This specification covers a titanium alloy in the form of sheet and strip up to 0.143 inch (3.63 mm), inclusive, in nominal thickness (see 8.6
This SAE Standard for reliability-centered maintenance (RCM) is intended for use by any organization that has or makes use of physical assets or systems that it wishes to manage responsibly
This specification covers a corrosion-resistant, premium aircraft-quality alloy steel in the form of bars, forgings, and stock for forging
This specification covers an aluminum alloy in the form of die forgings up to 4 inches (102 mm), inclusive, in thickness and hand forgings up to 6 inches (152 mm), inclusive, in thickness (see 8.6
This test code describes tests for determining characteristics of hydraulic positive displacement pumps used on off-road self-propelled work machines as referenced in SAE J1116
This SAE Standard provides test procedures, requirements, and guidelines for motorcycle turn signal lamps. It does not apply to mopeds
This SAE Standard applies to horizontal earthboring machines found in SAE J2022 of the following types: a Auger boring machines b Rod pushers c Rotary rod machines d Impact machines This document does not apply to horizontal directional drilling (HDD) machines as defined in ISO 21467, mining machinery covered in SAE J1116, Table 1, nor does it apply to conveyors, tunnel boring machines, pipe jacking systems, micro tunnelers, or well drilling machines
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This specification establishes requirements for titanium forgings of any shape or form from which finished parts are to be made (see 2.4.4, 8.3, and 8.6
This specification covers a tantalum alloy in the form of bars and rods up through 3.5 inches (88.9 mm), inclusive (see 8.5
To determine the ability of a fuel/water separator to separate emulsified or finely dispersed water from fuels. This test method is applicable for biodiesel fuel
This specification covers a corrosion and heat resistant steel in the form of sand castings
To determine the undissolved water removal performance of a fuel/water separator under controlled laboratory conditions, using water droplets. This test method is applicable for diesel and biodiesel fuel
SAE JA6097 (“Using a System Reliability Model to Optimize Maintenance”) shows how to determine which maintenance to perform on a system when that system requires corrective maintenance to achieve the lowest long-term operating cost. While this document may focus on applications to Jet Engines and Aircraft, this methodology could be applied to nearly any type of system. However, it would be most effective for systems that are tightly integrated, where a failure in any part of the system causes the entire system to go off-line, and the process of accessing a failed component can require additional maintenance on other unrelated components
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry
This SAE Systems Management Standard specifies the Habitability processes throughout planning, design, development, test, production, use and disposal of a system. Depending on contract phase and/or complexity of the program, tailoring of this standard may be applied. Appendix C provides guidance on tailoring standard requirements to fit the various DoD acquisition pathways. The primary goals of a contractor Habitability program include: Ensuring that the system design complies with the customer Habitability requirements and that discrepancies are reported to management and the customer. Identifying, coordinating, tracking, prioritizing, and resolving Habitability risks and issues and ensuring that they are: ◦ Reflected in the contractor proposal, budgets, and plans. ◦ Raised at design, management, and program reviews. ◦ Debated in working group meetings. ◦ Coordinated with Training, logistics, and the other HSI disciplines. ◦ Included appropriately in documentation and deliverable
SAE JA1012 (“A Guide to the Reliability-Centered Maintenance (RCM) Standard”) amplifies and clarifies each of the key criteria listed in SAE JA1011 (“Evaluation Criteria for RCM Processes”), and summarizes additional issues that must be addressed in order to apply RCM successfully
In order to compare test results obtained from different crash test facilities, standardized coordinate systems need to be defined for crash test dummies, vehicle structures, and laboratory fixtures. In addition, recorded polarities for various transducer outputs need to be defined relative to positive directions of the appropriate coordinate systems. This SAE Information Report describes the standardized sign convention and recorded output polarities for various transducers used in crash testing
This specification covers the requirements for electrodeposited bronze plate and its subsequent removal
Items per page:
50
1 – 50 of 210814