Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Recommended Practice establishes uniform test procedures for friction based parking brake components used in conjunction with hydraulic service braked vehicles with a gross vehicle weight rating greater than 4500 kg (10 000 lb). The components covered in this document are the primary actuation and the foundation park brake. Various peripheral devices such as application dashboard switches or indicators are not included. These test procedures include the following: a Brake Related Tests 1 Brake Functional Performance 2 Brake Dynamic Torque Performance 3 Brake Corrosion Resistance 4 Brake Endurance with Torque 5 Brake Endurance without Torque 6 Vibration Resistance 7 Brake Ultimate Static Load 8 Brake Lining Wear Adjuster Function b Actuation Related Tests 1 Mechanical Actuator Functional Performance 2 Mechanical Actuator Endurance 3 Mechanical Actuator Quick Release 4 Mechanical Actuator Ultimate Load 5 Spring Apply Actuator Functional Performance 6 Spring Apply Actuator
This SAE Aerospace Recommended Practice (ARP) establishes the overall component and system function guidelines and minimum performance levels for a TPMS. These guidelines include, but are not limited to: Design recommendations for system components, which: Monitor tire inflation Are located in/on the tire/wheel assembly, landing gear axle, and/or aircraft avionics compartment Recommended performance and safety guidelines for a TPMS.
This specification covers a corrosion-resistant steel in the form of wire.
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than, equal to, or greater than 2032 mm in overall width.
The mass of air required to burn a unit mass of fuel with no excess of oxygen or fuel left over is known as the stoichiometric air-fuel ratio. This ratio varies appreciably over the wide range of fuels - gasolines, diesel fuels, and alternative fuels - that might be considered for use in automotive engines. Although performance of engines operating on different fuels may be compared at the same air-fuel ratio or same fuel-air ratio, it is more appropriate to compare operation at the same equivalence ratio, for which a knowledge of stoichiometric air-fuel ratio is a prerequisite. This SAE Recommended Practice summarizes the computation of stoichiometric air-fuel ratios from a knowledge of a composition of air and the elemental composition of the fuel without a need for any information on the molecular weight of the fuel.
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Recommended Practice incorporates a track-based test procedure that produces a representative value for vehicle top speed when operating on a level paved road with a fully charged battery.
This SAE Standard defines a method for evaluating the immunity of automotive electrical/electronic devices to radiated electromagnetic fields coupled to the vehicle wiring harness. The method, called bulk current injection (BCI), uses a current probe to inject RF onto the wiring harness in the frequency range of 1 to 400 MHz. BCI is one of a number of test methods that can be used to simulate the electromagnetic field. The test method refers to ISO 11452-4 (please refer to ISO 11452-4 for test procedures). In addition to ISO 11452-4, this test method also includes a differential bulk current injection (DBCI) test. DBCI is described in Section 4 of this document.
This SAE Standard specifies the essential interface dimensions, the installation dimensions, and the operating requirements for hydraulic couplers employed to transmit hydraulic power from agricultural tractors to agricultural implements and farmstead equipment as defined in SAE J1150.
This SAE Recommended Practice applies to speedometers, odometers, and speedometer drives typical of passenger vehicles, buses, and trucks used for personal or commercial purposes. The method of determining wheel revolutions per unit distance (3.1) and overall system design variation (3.3.3) are applicable to passenger cars only. Comparable recommendations for trucks and buses are under development. The data of tachometers is applicable to vehicular use, as previously described, and also to stationary and marine engines and special vehicles.
This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
This SAE Metric Aerospace Standard (MA) specifies the drawing requirements for center holes when center holes are required on the finished part.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification covers a corrosion and heat resistant nickel alloy in the form of sand castings.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and foil.
This SAE Aerospace Standard (AS) provides requirements for design and installation of aircraft jacking pad adapters and the mating jack socket interface to permit use of standard jacking equipment to be used in civil and military transport aircraft. The adapter defined herein shall be the key interface between the aircraft and the aircraft jack(s).
This specification covers beryllium in the form of bar, rod, tubing, and shapes fabricated from impact-ground beryllium powder consolidated by cold isostatic pressing (CIP) and sintering.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of rods and wire.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars and forgings, flash welded rings, and stock for forging or flash welded rings.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers a corrosion-resistant steel in the form of bars, forgings, and forging stock.
This specification covers a corrosion and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
This specification covers a corrosion-resistant steel in the form of bars and wire 0.75 inch (19 mm) and under in nominal diameter or distance between parallel sides (thickness).
Items per page:
50
1 – 50 of 219531