Results
This SAE Aerospace Information Report (AIR) describes a method for assessing size dependent particle losses in a sampling and measurement system of specified geometry utilizing the non-volatile Particulate Matter (nvPM) mass and number concentrations measured at the end of the sampling system.1 The penetration functions of the sampling and measurement system may be determined either by measurement or by analytic computational methods. Loss mechanisms including thermophoretic (which has a very weak size dependence) and size dependent losses are considered in this method2 along with the uncertainties due to both measurement error and the assumptions of the method. The results of this system loss assessment allow development of estimated correction factors for nvPM mass and number concentrations to account for the system losses facilitating estimation of the nvPM mass and number at the engine exhaust nozzle exit plane. As the particle losses are size dependent, the magnitude of correction
The purpose of this document is to establish air-conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system; since these characteristics and conditions vary greatly from one application to another, the designer shall determine the goals expected to be reached under the conditions encountered. To determine the capacity of such items as blowers, condenser fans, condenser coils, evaporator coils, filters, compressors, etc., will require the adherence to several guidelines, some of which are outlined in the following paragraphs.
This SAE Recommended Practice establishes uniform test procedures for desiccant air dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant air dryers are excluded from the scope of this document.
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation to be used for measuring the exterior exhaust sound level for passenger cars, multipurpose vehicles, and light trucks under stationary conditions providing a continuous measure of exhaust system or simulated exhaust sound level over a range of engine speeds or simulated engine speeds. This document applies only to road vehicles equipped with an internal combustion engine or with an external sound system. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. It is within the scope of this document to measure the stationary A-weighted sound pressure level during: Measurements at the manufacturing stage Measurements at official testing stations Measurements at roadside testing It does neither specify a method to check the exhaust sound pressure level when the engine is operated at
This document sets forth general, functional, procedural, and design criteria and recommendations concerning human engineering of data link systems. The recommendations are based on limited evidence from empirical and analytic studies of simulated data link communication, and on experience from operational tests and actual use of data link. However, because data are not yet available to support recommendations on all potentially critical human engineering issues these recommendations necessarily go beyond the data link research and include requirements based on related research and human factors engineering practice. It is also recognized that evolution of these recommendations will be appropriate as experience with data link accumulates and new applications are implemented. This document focuses primarily on recommendations for data link communications between an air traffic specialist and a pilot, i.e., air traffic services communications, although some recommendations address use of
This SAE Aerospace Information Report (AIR) considers the following major areas: 1 major components and their ratings; 2 selection criteria for optimum design balance for electrical systems; 3 effects of operating conditions and environment on both maintenance and life of components; 4 trouble signals - their diagnosis and cure.
Test procedures are described for measuring noise at specific receiver locations (passenger and cargo doors, and servicing positions) and for conducting general noise surveys around aircraft. Procedures are also described for measuring noise level at source locations to facilitate the understanding and interpretation of the data. Requirements are identified with respect to instrumentation; acoustic and atmospheric environment; data acquisition, reduction and presentation, and such other information as is needed for reporting the results. This document makes no provision for predicting APU or component noise from basic engine characteristics or design parameters, nor for measuring noise of more than one aircraft operating at the same time. No attempt is made to suggest acceptable levels of noise or suitable subjective criteria for judging acceptability. ICAO Annex 16 Volume I Attachment C provides guidance on recommended maximum noise levels.
This method is intended to define the continuous upper temperature limit (CUTL) of thermoplastic elastomers and thermoset rubber with durometer hardness <=90 Shore A, to oxidation or other degradation when exposed solely to hot air for an extended period of time.
This SAE Recommended Practice is intended for testing of external automatic brake adjusters as they are used in service, emergency, or parking brake systems for on-highway vehicle applications.
This SAE standard establishes the requirement for suppliers to plan a reliability program that satisfies the following three requirements: a The supplier shall ascertain customer requirements b The supplier shall meet customer requirements c The supplier shall assure that customer requirements have been met
This SAE Standard provides test procedures, performance requirements, design guidelines, and installation guidelines for snowmobile tail (rear position) lamp.
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self-propelled work machines as defined by SAE J1116 (limited to categories of (1) construction, and (2) general purpose industrial).
This SAE Recommended Practice describes a procedure for locating the three-dimensional reference system on a motor vehicle as built.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Recommended Practice (RP) specifies a dynamometer test procedure to characterize wear rates of automotive service brake linings (brake shoes) and disc brake pads.
This procedure is applicable to brake pad modes between 500 Hz and 16 kHz. The parameters measured with this procedure are defined as the first three natural frequencies, fn (n = 1, 2, 3), and the corresponding loss factors, η.
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
This SAE Recommended Practice establishes a uniform, powered vehicle test procedure and minimum performance requirement for lane departure warning systems used in highway trucks and buses greater than 4546 kg (10000 pounds) gross vehicle weight (GVW). Systems similar in function but different in scope and complexity, including lane keeping/lane assist and merge assist, are not included in this document. This document does not apply to trailers, dollies, etc. This document does not intend to exclude any particular system or sensor technology. This document will test the functionality of the lane departure warning system (LDWS) (e.g., ability to detect lane presence and ability to detect an unintended lane departure), its ability to indicate LDWS engagement, its ability to indicate LDWS disengagement, and its ability to determine the point at which the LDWS notifies the human machine interface (HMI) or vehicle control system that a lane departure event is detected. Moreover, this
In order to compare test results obtained from different crash test facilities, standardized coordinate systems need to be defined for crash test dummies, vehicle structures, and laboratory fixtures. In addition, recorded polarities for various transducer outputs need to be defined relative to positive directions of the appropriate coordinate systems. This SAE Information Report describes the standardized sign convention and recorded output polarities for various transducers used in crash testing.
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors. The equipment specified here will identify smaller refrigerant leaks when servicing motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning the equipment design or use beyond that of sampling a flammable refrigerant, save those described in 3.1 and 3.2 of this document. All requirements of this standard shall be verified in SAE J2911.
This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
This document presents a catalog of safety sign text and artwork that can be used by any ready mixed concrete truck manufacturer to warn of common hazards.
This document applies to prognostics of aerospace propulsion systems. Its purpose is to define the meaning of prognostics in this context, explain their potential and limitations, and to provide guidelines for potential approaches for use in existing condition monitoring environments. This document also includes some examples. The current revision does not provide specific guidance on validation and verification, nor does it address implementation aspects such as computational capability or certification.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a closed cell silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
This specification covers an aluminum alloy in the form of sheet and plate 0.020 to 2.000 inches (0.51 to 50.80 mm), inclusive, in nominal thickness, supplied in the annealed (-O) condition (see 8.3). When specified, product shall be supplied in the “as fabricated” (-F) temper.
This SAE Recommended Practice applies only to excavators, as defined in ISO 6165, working above ground, near an excavated or free-standing bank or mine face which is higher than the top of the cab, or in demolition applications of freestanding buildings or objects higher than the top of the cab.
Items per page:
50
1 – 50 of 211286