Results
The scope of this SAE performance standard is to provide a simple, practical, and broadly applicable test procedure for appraising luminous Illuminant A reflectance of reflecting safety glazing materials for road vehicles. This SAE performance standard, which provides a simple test procedure widely used in the optics field, may be used to measure the reflectivity which films applied to safety glazing materials for road vehicles may enhance. This test procedure applies to conditions where feasibility, rather than accuracy of measurement, is of prime importance. Measurements can be made outside laboratories in a quality control environment and in similar applications, when glazings, instead of small test specimens, have to be tested.
This specification covers a magnesium alloy in the form of sand castings (see 8.6).
This specification covers the requirements for glass fabric base plastic honeycomb core materials for aircraft structural applications, including aircraft exterior parts, such as radio and radar antenna housings, and other parts.
This specification presents the requirements for one type of a heat-sensitive recording paper, in roll form, that furnishes permanent marking or tracing on one side.
This specification covers chrome-molybdenum (4130) steel bars and forging stock of aircraft quality.
This specification covers the requirements for surface bonded laminated shim stock.
This specification covers discontinuously reinforced aluminum alloy (DRA) metal matrix composites (MMC) made by mechanical alloying of the 2124A powder and SiC particulate, which is then consolidated by hot isostatic pressing (HIP) into shapes less than 62 square inches (0.04 m2) in cross-sectional area (see 8.12).
This specification covers an aircraft-quality, low-alloy steel in the form of round, non-welded tubing free from OD surface seams.
This specification establishes the requirements for a waterborne, corrosion-inhibiting, chemical- and solvent-resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
This specification covers electric furnace steel bars and reforging stock of aircraft quality.
This specification covers the requirements for procurement of one grade of powdered molybendum disulfide to be used in lubricants and greases for surfaces where boundary conditions exist.
This specification covers grease for use on aircraft wheel bearings. It also defines the quality control requirements to assure batch conformance and materials traceability and the procedures to manage and communicate changes in the grease formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in 2.2, referencing this specification. Products qualified to this specification are listed on a qualified products list (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before a grease is approved for use in their equipment. Approval and/or certification for use of a specific grease in aero and aero-derived marine and industrial applications is the responsibility of the individual equipment builder and/or governmental authorities and is not implied by compliance with or qualification to this
This specification covers bonded honeycomb core made of aluminum alloy and supplied in the form of blocks, slices, or other configurations as ordered (see 8.5).
This specification covers the requirements for a hard anodic coating on magnesium alloys and the properties of the coating.
This specification covers class L, low dielectric constant (12 or under), ceramic, electrical, insulating compounds, for use in electronic, communications, and allied electrical equipments, and the grading thereof (see 6.1).
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded in place gaskets for aeronautical and aerospace applications.
This specification covers three types of rubber having good resistance to high and low temperature and hydrazine type propellants, but poor resistance to hydrocarbon oils or solvents. Hydrazines are hazardous chemicals. See “Dangerous Properties of Industrial Materials” by N. Irving Sax.
This specification establishes the requirements for fabricated products of vulcanized rubber, synthetic rubber or rubberlike compositions alone or in combination, together with procedures for the inspection of such products (see 6.1).
This specification covers the requirements of composite blankets suitable for acoustical and thermal insulation of the walls of aircraft compartments within the temperature range of -65°F to +175°F (-54°C to +80°C).
This specification covers the general requirements for aluminum and aluminum alloy tube; drawn, seamless (see 6.1.1). Specific requirements for these products in a particular alloy are covered by the applicable detail specification (see 6.3).
This specification covers a concentrated rust removing compound in the form of a liquid to be diluted with water for use either at ambient or elevated temperature.
This SAE Recommend Practice specifies a method for measuring the deflection of friction materials and disc brake pad assemblies in a manner more consistent with classical material compressive strain testing. This SAE test method differs from SAE J2468 in the preload and maximum load applied to the test sample when deflection is measured. It adopts the material applied stress levels found in ISO 6310 (0.5 to 8.0 MPa) using a 25 mm diameter flat plunger.
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications. For sheet, strip, tubing, extrusions, and molded shapes use the AMS3353 specification which is intended for that use.
This specification covers a water-base cleaner in the form of a liquid.
This specification covers high temperature, compression set, and fluid resistant fluorocarbon elastomer sheets, strips, molded parts, and extruded shapes for aeronautical and aerospace applications.
Items per page:
50
1 – 50 of 212301