Results
This SAE Recommended Practice covers transfer cases used in passenger car and light truck applications. Transfer cases are of the chain, geared, manually and electronically shifted types although other configurations are possible. The operating points (speeds, temperatures, etc.) were chosen to mirror those of the United States Environmental Protection Agency Vehicle Chassis Dynamometer Driving Schedules (DDS
This SAE Recommended Practice establishes the method to determine Sound Level of a snowmobile under typical trail operating conditions. Snowmobiles have different engine power levels that depends on the model
This SAE standard specifies a method for testing and measuring a normalized elastic constant of brake pad assemblies using ultrasound. This document applies to disc brake pad assemblies and its coupons or segments used in road vehicles
This SAE Recommended Practice establishes for trucks, buses, and multipurpose passenger vehicles with GVW of 4500 kg (10 000 lb) or greater: a Minimum performance requirements for the switch for activating electric or electro-pneumatic windshield washer systems. b Uniform test procedures that include those tests that can be conducted on uniform test equipment by commercially available laboratory facilities. The test procedures and minimum performance requirements, outlined in this document, are based on currently available engineering data. It is the intent that all portions of the document will be periodically reviewed and revised as additional data regarding windshield washing system performance is developed
This Recommended Practice provides procedures for defining the Accelerator Heel Point and the Accommodation Tool Reference Point, a point on the seat H-point travel path which is used for locating various driver workspace accommodation tools in Class B vehicles (heavy trucks and buses). Three accommodation tool reference points are available depending on the percentages of males and females in the expected driver population (50:50, 75:25, and 90:10 to 95:5). These procedures are applicable to both the SAE J826 HPM and the SAE J4002 HPM-II
This SAE Standard applies to the application of ultraviolet leak detection to service mobile air-conditioning systems
An airbag generates a considerable amount of kinetic energy during its inflation process. As a result substantial forces can be developed between the deploying airbag and the out-of-position occupant. Accident data and laboratory test results have indicated a potential for head, neck, chest, abdominal, and leg injuries from these forces. This suggests that mitigating such forces should be considered in the design of airbag restraint systems. This document outlines a comprehensive set of test guidelines that can be used for investigating the interactions that occur between the deploying airbag and the occupant who is near the module at the time of deployment. Static and dynamic tests to investigate driver and passenger systems are given. Static tests may be used to sort designs on a comparative basis. Designs that make it through the static sorting procedure may be subjected to the appropriate dynamic tests. On a specific vehicle model, engineering judgment based upon prior experience
This Recommended Practice provides a procedure to locate driver seat tracks, establish seat track length, and define the SgRP in Class B vehicles (heavy trucks and buses). Three sets of equations that describe where drivers position horizontally adjustable seats are available for use in Class B vehicles depending on the percentages of males to females in the expected driver population (50:50, 75:25, and 90:10 to 95:5). The equations can also be used as a checking tool to estimate the level of accommodation provided by a given length of horizontally adjustable seat track. These procedures are applicable for both the SAE J826 HPM and the SAE J4002 HPM-II
This SAE standard applies to any and all additives and chemical solutions intended for aftermarket use in the refrigerant circuit of vehicle air-conditioning systems with belt-driven compressors, except as noted below. This standard provides testing and acceptance criteria for determining the stability and compatibility of additives and flushing materials (solutions) with A/C system materials and components, that may be intended for use in servicing or operation of vehicle air conditioning systems. This standard does not provide test criteria for additive, compressor lubricant, or flushing solution effectiveness; such testing is the responsibility of the additive and/or solution manufacturer/supplier. This standard does not cover additives or flushing materials for electrically driven compressors. The use of additives with electrically driven compressors might cause electrical shorting and compressor failure. It is not the intent of this document to identify the requirements for
This SAE Aerospace Standard (AS) provides a performance station designation system for aircraft propulsion systems and their derivatives
This SAE Recommended Practice provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system
This SAE Standard describes guarding to help prevent hazardous machine movement caused by activation of the starter motor by bypassing the starter control system. This document is applicable to off-road, self-propelled work machines, as identified in SAE J1116, and agricultural tractors, as defined in ANSI/ASAE S390, which have the potential for hazardous machine movement as a result of bypassing the starter control system and powering of the starter motor
This SAE Recommended Practice describes two-dimensional 95th percentile truck driver side view, seated stomach contours for horizontally adjustable seats (see Figure 1). There is one contour and three locating lines to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5
This SAE Recommended Practice describes the test procedures for conducting dynamic frontal strength test for COE heavy truck applications. Its purpose is to establish recommended test procedures which will standardize the procedure for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included
This specification establishes a procedure for designating minimum stress-rupture property requirements of castings by means of this AMS number and a series of dash numbers
This specification establishes a procedure for designating minimum room temperature tensile property requirements of castings by means of this AMS number and a series of dash numbers
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing produced with cross-sectional area of 32 square inches (206 cm2), maximum (see 8.5
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars up to 4.00 inches (101.6 mm) exclusive in nominal diameter or thickness, forgings 4.00 inches (101.6 mm) exclusive in nominal thickness, flash welded rings up to 4.00 inches (101.6 mm) exclusive in nominal radial thickness, and stock of any size for forging or flash welded rings (see 8.6
This brief User Guide recaps the content of the AS6518B UCS Architectural Model. The purpose of the UCS Architecture Model is to provide the authoritative source for other models and products within the UCS Architecture as shown in the AS6512B UCS Architecture: Architecture Description
This document provides a mapping between provider service identifiers (PSIDs)—allocated to SAE by the appropriate registration authorities—and SAE technical specifications of applications identified by those PSIDs. It is intended that this document will be updated regularly, including information about the publication status of SAE technical reports
This document describes machine-to-machine (M2M) communication to enable cooperation between two or more participating entities or communication devices possessed or controlled by those entities. The cooperation supports or enables performance of the dynamic driving task (DDT) for a subject vehicle with driving automation feature(s) engaged. Other participants may include other vehicles with driving automation feature(s) engaged, shared road users (e.g., drivers of manually operated vehicles or pedestrians or cyclists carrying personal devices), or road operators (e.g., those who maintain or operate traffic signals or workzones). Cooperative driving automation (CDA) aims to improve the safety and flow of traffic and/or facilitate road operations by supporting the movement of multiple vehicles in proximity to one another. This is accomplished, for example, by sharing information that can be used to influence (directly or indirectly) DDT performance by one or more nearby road users
This document describes [motor] vehicle driving automation systems that perform part or all of the dynamic driving task (DDT) on a sustained basis. It provides a taxonomy with detailed definitions for six levels of driving automation, ranging from no driving automation (Level 0) to full driving automation (Level 5), in the context of [motor] vehicles (hereafter also referred to as “vehicle” or “vehicles”) and their operation on roadways: Level 0: No Driving Automation Level 1: Driver Assistance Level 2: Partial Driving Automation Level 3: Conditional Driving Automation Level 4: High Driving Automation Level 5: Full Driving Automation These level definitions, along with additional supporting terms and definitions provided herein, can be used to describe the full range of driving automation features equipped on [motor] vehicles in a functionally consistent and coherent manner. “On-road” refers to publicly accessible roadways (including parking areas and private campuses that permit
This specification covers one type of fluorescent magnetic particles in the form of a mixed, ready-to-use suspension in an odorless, inspection oil vehicle and packaged in aerosol cans
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit
Systems shall be classified in terms of type, category and class
This SAE Aerospace Information Report (AIR) provides the hydraulic and flight-control system designer with the various design options and techniques that are currently available to enhance the survivability of military aircraft. The AIR addresses the following major topics: a Design concepts and architecture (see 3.2, 3.5, and 3.6) b Design implementation (see 3.3, 3.6, and 3.7) c Means to control external leakage (see 3.4) d Component design (see 3.8
Items per page:
50
1 – 50 of 211737