Results
This specification covers epoxy-resin-impregnated glass laminates in the form of sheets clad on one or both sides with electrolytic copper foil.
This specification covers felted wool fibers in the form of sheets and rolls.
This specification covers felted wool fibers in the form of sheets and rolls.
This SAE Aerospace Recommended Practice (ARP) covers visible surface defects on aerospace hose assemblies which have been installed and are functioning within a working environment at the time of visual inspection.
This specification covers a virgin, unfilled polytetrafluoroethylene (PTFE) in the form of extruded and sintered rods, tubes, and profiles.
This report lists military and industry specifications and standards which are used in aerospace engine starting and auxiliary power systems. Listings are provided as follows: Section 2. Topic Listing Section 3. Numerical Listing Section 4. Alphabetical Listing Only those hardware standards which have been specifically designed for engine starting systems are listed. Revisions and amendments which are current for these specifications and standards are not listed.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear fog lamp systems.
This SAE Recommended Practice establishes the test procedure, environment, instrumentation, and data analyses for comparing interior sound level of passenger cars, multipurpose vehicles, and light trucks having gross vehicle weight rating (GVWR) of 4540 kg (10 000 lb) or less. The test procedure is characterized by having fixed initial conditions (specified initial vehicle speed and gear selection at the starting point on the test site) to obtain vehicle interior sound measurement during road load operation over various road surfaces at specified constant speeds. The measurement data so derived is useful for vehicle engineering development and analysis.
This ARP describes recommended sampling conditions, instrumentation, and procedures for the measurement of nonvolatile particle number and mass concentrations from the exhaust of aircraft gas turbine engines. Procedures are included to estimate sampling system loss performance. This ARP is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode. This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
The purpose of this SAE Recommended Practice is to provide a common electrical and mechanical interface specification that can be used to design electronic accelerator pedal position sensors and electronic control systems for use in medium- and heavy-duty vehicle applications.
This SAE Recommended Practice applies to S-CAM, wedge, and disc air brake actuators where the stroke can be measured without disassembly from the brake.
This SAE Standard presents a method of determining the stiffness of interior trim materials, substrates, and composites by a three-point bending test.
This SAE Recommended Practice is intended for use in testing and evaluating the performance of electric cooling fan (ECF) assemblies typically used for vehicle engine cooling. Conducted in a laboratory environment with intended heat exchangers, the performance measurement includes fan output in terms of airflow and pressure and fan motor input in terms of voltage and current. This information can be used to calculate the efficiency of the assembly, including aerodynamic efficiency of the fan and shroud, and electrical efficiency of the motor. The electric power consumption can be used to estimate electrical charging system sizing and fuel economy. The performance of a given fan assembly depends on the installation details of the application, including the effects of system resistance and geometries of the grill, heat exchangers, engine and other underhood components, and front end components. This document provides guidance for duplicating such details in the test setup for accurate
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated, operator controlled forward warning horn devices, primarily intended for use on self-propelled, work machines as defined by SAE J1116 (limited to categories of (1) construction and (2) general purpose industrial).
This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These are often called “mini coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the mini coax connection system described here is 50 Ω, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable.
This standard covers supplemental requirements for low tension primary cable intended for use as Fusible Links (Fuse Links) at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. These supplemental requirements are intended to qualify cables for an extreme current overload.
This AIR points out that above a frequency called the “transition frequency,” variances associated with the shielding effectiveness measurements can become large. It includes the derivations to demonstrate this. This fact should be taken into account when designing shielding for use above the transition frequency.
This SAE Standard defines requirements relating to the elements of design, operation, and maintenance of light utility vehicles (LUVs). The safety specifications in this document apply to any self-propelled, operator-controlled, off-highway vehicle 1829 mm (72 inches) or less in overall width, exclusive of added accessories and attachments, operable on three or more wheels or tracks, primarily intended to transport material loads or people, with a gross vehicle weight of 2500 kg (5500 pounds) or less, and a maximum design speed less than or equal to 40.23 km/h (25 mph). This document is not intended to cover go-karts (ASTM F2007-07a), fun-karts (ASTM F2011-02e1), dune buggies, and all terrain-vehicles (ATVs) complying with ANSI/SVIA 1.
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
This SAE Aerospace Standard (AS) covers any protective system that serves the stated purpose.
This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems.
The purpose of this SAE Recommended Practice is to establish reference standards for airflow measurements in the ranges required for testing automotive engine induction systems and to describe equipment that will facilitate the use of such standards to check the accuracy of various equipment and methods.
This SAE Recommended Practice describes performance requirements for hardware used in motor vehicle seat belt assemblies when tested in accordance with the test procedures specified in SAE J140. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.
Items per page:
50
1 – 50 of 211951