Results
This specification covers upholstery fabrics woven from nylon and treated for fire retardation.
This specification covers a general purpose disinfectant in the form of a concentrated liquid to be used diluted in accordance with label instructions.
This specification covers two types of aircraft glass window cleaners in the form of a ready-to-use liquid.
This specification covers a concentrated rust removing compound in the form of a liquid to be diluted with water for use either at ambient or elevated temperature.
This SAE Recommend Practice specifies a method for measuring the deflection of friction materials and disc brake pad assemblies in a manner more consistent with classical material compressive strain testing. This SAE test method differs from SAE J2468 in the preload and maximum load applied to the test sample when deflection is measured. It adopts the material applied stress levels found in ISO 6310 (0.5 to 8.0 MPa) using a 25 mm diameter flat plunger.
This SAE Standard specifies a method for testing and measuring elastic constants in friction materials by precise ultrasonic velocity measurements. Measurement methods are also described for measurement of the out-of-plane modulus as a function of pre-load as well as the measurement of engineering constants as a function of temperature. Finally, methods are formulated to produce all engineering constants as a function of pre-load and temperature.
This specification covers an alkaline rust remover compound in the form of a liquid concentrate or a water-soluble powder for dilution with water.
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications. For sheet, strip, tubing, extrusions, and molded shapes use the AMS3353 specification which is intended for that use.
This specification covers a water-base cleaner in the form of a liquid.
This specification covers a series of iron-nickel, iron-nickel-cobalt, and iron-nickel-chromium alloys used for sealing to glasses and ceramics in electronic applications (see 6.1).
This specification covers the general requirements for aluminum and aluminum alloy tube; drawn, seamless (see 6.1.1). Specific requirements for these products in a particular alloy are covered by the applicable detail specification (see 6.3).
This specification covers three types of rubber having good resistance to high and low temperature and hydrazine type propellants, but poor resistance to hydrocarbon oils or solvents. Hydrazines are hazardous chemicals. See “Dangerous Properties of Industrial Materials” by N. Irving Sax.
This specification establishes the requirements for fabricated products of vulcanized rubber, synthetic rubber or rubberlike compositions alone or in combination, together with procedures for the inspection of such products (see 6.1).
This specification covers the requirements of composite blankets suitable for acoustical and thermal insulation of the walls of aircraft compartments within the temperature range of -65°F to +175°F (-54°C to +80°C).
This specification covers chromium-molybdenum (4130) seamless and welded steel tubing of aircraft quality.
This specification covers a methyl phenyl vinyl silicone rubber material that can be used to manufacture product in the form of sheet, strip, tubing, molded shapes, and extrusions. For molded rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the corresponding AMS7000 series specification.
This specification covers aluminum alloy die castings.
This specification presents requirements for thin-walled (inside diameter greater than four times the wall thickness and outside diameter 1/4 inch and larger) corrosion-resistant steel tubing in approximately the 1/8 hard condition, of special quality, suitable for use in high-pressure hydraulic systems.
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-rings or molded O-ring cord, and molded in place gaskets for aeronautical and aerospace applications.
The information presented herein describes the commonly observed patterns of O-ring failure by means of both text and illustration. Possible causes and corrective actions are indicated for alleviating the problem.
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded in place gaskets for aeronautical and aerospace applications.
The specification establishes the requirements for a liquid cleaning compound intended for use in steam cleaning machines to clean metallic and painted, soiled surfaces.
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-rings, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications.
This specification covers a butadiene-acrylonitrile (NBR) rubber in the form of molded rings, compression seals, o-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications.
This specification covers a solvent-type remover in the form of a liquid.
This specification establishes requirements for a corrosion-removing compound in the form of a liquid concentrate.
This specification covers a fluorocarbon (FKM) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. For molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the AMS7259 specification.
This specification covers an acrylonitrile-butadiene (NBR) rubber in the form of molded rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications. For sheet, strip, tubing, extrusions, and molded shapes, use the AMS3XXX specification which is intended for that use.
Items per page:
50
1 – 50 of 212300