Search
Advanced Search
of the following are true
(
)

Results

Items (212,369)
This document recommends design and performance criteria for aircraft lighting systems used to illuminate flight deck controls, luminous visual displays used for transfer of information, and flight deck background and instrument surfaces that form the flight deck visual environment. This document is for aircraft, except for applications requiring night vision compatibility.
A-20A Crew Station Lighting
The scope of this SAE performance standard is to provide a simple, practical, and broadly applicable test procedure for appraising luminous Illuminant A reflectance of reflecting safety glazing materials for road vehicles. This SAE performance standard, which provides a simple test procedure widely used in the optics field, may be used to measure the reflectivity which films applied to safety glazing materials for road vehicles may enhance. This test procedure applies to conditions where feasibility, rather than accuracy of measurement, is of prime importance. Measurements can be made outside laboratories in a quality control environment and in similar applications, when glazings, instead of small test specimens, have to be tested.
Glazing Materials Standards Committee
Specific federal aviation regulations (Titled 14 of the United States Code of Federal Regulations, or 14 CFR) define oxygen system requirements for an in-flight decompression incident. This AIR addresses the operational oxygen system requirements for a decompression incident that may occur at any point during a long-range flight, with an emphasis for a decompression at the equal time point (ETP). This AIR identifies fuel and oxygen management contingencies, and presents possible solutions for the efficient, safe, and optimum fuel/oxygen flight continuation. Oxygen management is a concern to all aircraft, such as single engine types that fly above 10 000 feet and use supplemental oxygen. This document provides a method which can help guide users in developing an oxygen solution for their aircraft.
A-10 Aircraft Oxygen Equipment Committee
This SAE Aerospace Standard (AS) establishes the requirements for 24° cone flareless fluid connection fittings and nuts and bite type flareless sleeves (see Section 6) for use in aircraft fluid systems at an operating pressure of 5000 psi for the fittings and nuts and 3000 psi for the bite type sleeves.
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This specification covers a petroleum base material in the form of a liquid.
AMS B Finishes Processes and Fluids Committee
This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness.
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a low expansion iron alloy in the form of sheet or strip 0.250 inch (6.35 mm) and under in nominal thickness.
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Information Report applies to structural integrity, performance, drivability, and serviceability of personally licensed vehicles not exceeding 10000 pounds GVWR such as sedans, crossovers, SUVs, MPVs, light trucks, and van-type vehicles that are powered by gas and alternative fuel such as electric, plug-in hybrid, or hybrid technologies. It provides engineering direction to vehicle modifiers in a manner that does not limit innovation, and it specifies procedures for preparing vehicles to enhance safety during vehicle modifications. It further provides guidance and recommendations for the minimum acceptable design requirements and performance criteria on general and specific structural modifications, thereby allowing consumers and third-party payers the ability to obtain and purchase equipment that meets or exceeds the performance and safety of the OEM production vehicle.
Adaptive Devices Standards Committee
This SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications, due to the potential leak path caused by the Inside Diameter (ID) weld bead or scarfed region. Assumption of risks when using this material for single flare applications shall be defined by agreement between the producer and purchaser. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of SAE J356 and SAE J356 Type-A are the same. The SAE J356 or SAE J356 Type-A designation define unique manufacturing differences between coiled and straight material. Nominal reference working pressures for this tubing are listed in ISO 10763 for metric tubing, and SAE
Metallic Tubing Committee
This SAE Standard encompasses connectors between two cables or between a cable and an electrical component and focuses on the connectors external to the electrical component. This document provides environmental test requirements and acceptance criteria for the application of connectors for direct current electrical systems of 60 V or less in the majority of heavy-duty applications typically used in off-highway machinery. Severe applications can require higher test levels or field-testing on the intended application.
CTTC C2, Electrical Components and Systems
This specification establishes requirements for three types of corrosion-preventative coatings for protection of aircraft integral fuel tanks.
AMS G8 Aerospace Organic Coatings Committee
This SAE Recommended Practice defines the minimum performance specifications for sensors used within anthropomorphic test devices (ATDs) when performing impact tests per SAE J211. It is intended that any agency proposing to conduct tests in accordance with SAE J211 shall be able to demonstrate that the transducers they use would meet the performance requirements specified in this document.
Safety Test Instrumentation Standards Committee
This specification establishes the engineering requirements for producing an anodic coating on titanium and titanium alloys and the properties of the coating.
AMS B Finishes Processes and Fluids Committee
This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness.
AMS F Corrosion and Heat Resistant Alloys Committee
This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness.
AMS F Corrosion and Heat Resistant Alloys Committee
The video systems include a camera, display, and lights. Video is the recording, reproducing, or broadcasting of moving visual images as illustrated in Figure 1. A camera video imaging system is a system composed of a camera and a monitor, as well as other components, in which the monitor provides a real-time or near real-time visual image of the scene captured by the camera. Such systems are capable of providing remote views to the pilot and can therefore be used to provide improved visibility (for example, coverage of blind spots). In general, camera video systems may be used in the pilot’s work position for purposes of improving airplane and corresponding environmental visibility. Examples of aircraft video system applications include: Ground maneuver or taxi camera system Flight deck entry video surveillance system Cargo loading and unloading Cargo compartment livestock monitoring Monitoring systems that are used to track the external, internal, and security functions of an
A-20B Exterior Lighting Committee
This specification covers discontinuously reinforced aluminum alloy (DRA) metal matrix composites (MMC) made by mechanical alloying of the 2124A powder and SiC particulate, which is then consolidated by hot isostatic pressing (HIP) into shapes less than 62 square inches (0.04 m2) in cross-sectional area (see 8.12).
AMS D Nonferrous Alloys Committee
This specification covers class L, low dielectric constant (12 or under), ceramic, electrical, insulating compounds, for use in electronic, communications, and allied electrical equipments, and the grading thereof (see 6.1).
AMS P Polymeric Materials Committee
The intended upper bound of this specification is that the particle size distribution (PSD) of powders supplied shall be <60 mesh (250 microns) and that no powder (0.0 wt.%) greater than 40 mesh (425 microns) is allowed.
AMS AM Additive Manufacturing Metals
This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment, special ordnance, and related accessories.
AMS E Carbon and Low Alloy Steels Committee
This specification covers electric furnace steel bars and reforging stock of aircraft quality.
AMS E Carbon and Low Alloy Steels Committee
This specification covers the procurement of granular heat-treating salts suitable for use in the molten state.
AMS B Finishes Processes and Fluids Committee
This specification covers treated aluminum core material for structural sandwich construction.
AMS P17 Polymer Matrix Composites Committee
This specification covers the requirements for procurement of one grade of powdered molybendum disulfide to be used in lubricants and greases for surfaces where boundary conditions exist.
AMS B Finishes Processes and Fluids Committee
This specification covers the requirements for electroless (autocatalytic chemical reduction) deposition of nickel-phosphorous alloy coatings on metal and composite surfaces.
AMS B Finishes Processes and Fluids Committee
This specification covers pasted-mica electrical insulation for molded armature slot bases, commutator insulation, shells, heating elements, and other similar insulating purposes.
AMS P Polymeric Materials Committee
This specification covers cored and uncored open cell latex foam rubber sheets, molded and hand- built shapes having good shock-absorbing, vibration-damping, and comfort cushioning characteristics (see 6.1).
AMS P Polymeric Materials Committee
This specification covers the requirements for surface bonded laminated shim stock.
AMS D Nonferrous Alloys Committee
This specification covers the requirements for glass fabric base plastic honeycomb core materials for aircraft structural applications, including aircraft exterior parts, such as radio and radar antenna housings, and other parts.
AMS P17 Polymer Matrix Composites Committee
This specification presents the requirements for one type of a heat-sensitive recording paper, in roll form, that furnishes permanent marking or tracing on one side.
AMS P Polymeric Materials Committee
This specification covers chrome-molybdenum (4130) steel bars and forging stock of aircraft quality.
AMS E Carbon and Low Alloy Steels Committee
This document establishes general design criteria, tolerances, and limits of application for tooling, fixtures and accessories for mounting and driving gas turbine engine rotors on horizontal and vertical balancing machines. For your own safety, while using balancing tooling, regard the safety instructions of the individual supplier.
EG-1A Balancing Committee
This specification establishes the requirements for fabricated products of vulcanized rubber, synthetic rubber or rubberlike compositions alone or in combination, together with procedures for the inspection of such products (see 6.1).
AMS CE Elastomers Committee
This specification covers the requirements of composite blankets suitable for acoustical and thermal insulation of the walls of aircraft compartments within the temperature range of -65°F to +175°F (-54°C to +80°C).
AMS CE Elastomers Committee
The purpose of this military standard is to prescribe the non-destructive testing acceptance criteria for the inspection of metal castings that are classified (see 1.3) in accordance with this standard.
AMS B Finishes Processes and Fluids Committee
Items per page:
1 – 50 of 212369