Results
This SAE Standard is equivalent to ISO 362-1:2015 and specifies an engineering method for measuring the noise emitted by road vehicles of categories M and N under typical urban traffic conditions. It excludes vehicles of category L1, L2, L3, L4, and L5. The specifications are intended to reproduce the level of noise generated by the principal noise sources during normal driving in urban traffic. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustical environment that is obtained only in an extensive open space. Such conditions are usually provided for during: Measurements of vehicles for regulatory certification and/or type approval Measurements at the manufacturing stage Measurements at official testing stations Annex A provides background information on the use of this standard consistent with the intent.
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inches, incl (19.05 to 38.10 mm, incl) in thickness (see 8.6).
This specification establishes the engineering requirements for producing an anodic coating on titanium and titanium alloys and the properties of the coating.
This specification establishes requirements for three types of corrosion-preventative coatings for protection of aircraft integral fuel tanks.
This specification covers a corrosion-resistant steel in the form of sheet and strip.
This specification covers a corrosion-resistant steel in the form of sheet and strip 0.005 inch (0.13 mm) and over in nominal thickness.
This aerospace test standard establishes the requirements and procedures for evaluating and comparing the impulse fatigue performance of high pressure hydraulic fittings and tubing. This test method may be used to test similar fluid system components, if desired.
This SAE Recommended Practice establishes the procedure for measuring the maximum exterior sound level of recreational motorboats while being operated under a variety of operating conditions. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This SAE Recommended Practice was developed by SAE and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM and NLGI. It is intended to assist those concerned with the design of heavy-duty vehicle components and with the selection and marketing of greases for the lubrication of certain components on heavy-duty vehicles like trucks and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of heavy-duty vehicle greases.
This SAE Recommended Practice defines the minimum performance specifications for sensors used within anthropomorphic test devices (ATDs) when performing impact tests per SAE J211. It is intended that any agency proposing to conduct tests in accordance with SAE J211 shall be able to demonstrate that the transducers they use would meet the performance requirements specified in this document.
This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness.
This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness.
This SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications, due to the potential leak path caused by the Inside Diameter (ID) weld bead or scarfed region. Assumption of risks when using this material for single flare applications shall be defined by agreement between the producer and purchaser. This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of SAE J356 and SAE J356 Type-A are the same. The SAE J356 or SAE J356 Type-A designation define unique manufacturing differences between coiled and straight material. Nominal reference working pressures for this tubing are listed in ISO 10763 for metric tubing, and SAE
This SAE Standard encompasses connectors between two cables or between a cable and an electrical component and focuses on the connectors external to the electrical component. This document provides environmental test requirements and acceptance criteria for the application of connectors for direct current electrical systems of 60 V or less in the majority of heavy-duty applications typically used in off-highway machinery. Severe applications can require higher test levels or field-testing on the intended application.
This SAE Information Report applies to structural integrity, performance, drivability, and serviceability of personally licensed vehicles not exceeding 10000 pounds GVWR such as sedans, crossovers, SUVs, MPVs, light trucks, and van-type vehicles that are powered by gas and alternative fuel such as electric, plug-in hybrid, or hybrid technologies. It provides engineering direction to vehicle modifiers in a manner that does not limit innovation, and it specifies procedures for preparing vehicles to enhance safety during vehicle modifications. It further provides guidance and recommendations for the minimum acceptable design requirements and performance criteria on general and specific structural modifications, thereby allowing consumers and third-party payers the ability to obtain and purchase equipment that meets or exceeds the performance and safety of the OEM production vehicle.
This specification covers a corrosion-resistant steel in the form of sheet and strip over 0.005 inch (0.13 mm) in nominal thickness.
This specification covers a low expansion iron alloy in the form of sheet or strip 0.250 inch (6.35 mm) and under in nominal thickness.
This specification covers grease for use within an aircraft. It also defines the quality control requirements to assure batch conformance and materials traceability and the procedures to manage and communicate changes in the grease formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in 2.2, referencing this specification. Products qualified to this specification are listed on a Qualified Products List (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before a grease is approved for use in their equipment. Approval and/or certification for use of a specific grease in aero and aero-derived marine and industrial applications is the responsibility of the individual equipment builder and/or governmental authorities and is not implied by compliance with or qualification to this specification.
This specification establishes the requirements for a waterborne, corrosion-inhibiting, chemical- and solvent-resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).
This specification covers grease for use on aircraft wheel bearings. It also defines the quality control requirements to assure batch conformance and materials traceability and the procedures to manage and communicate changes in the grease formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in 2.2, referencing this specification. Products qualified to this specification are listed on a qualified products list (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before a grease is approved for use in their equipment. Approval and/or certification for use of a specific grease in aero and aero-derived marine and industrial applications is the responsibility of the individual equipment builder and/or governmental authorities and is not implied by compliance with or qualification to this
The AMS1428 specification defines the technical requirements for Type II, III, and IV aircraft deicing/anti-icing fluids. These non-Newtonian thickened fluids are formulated to effectively remove frost, ice, and snow from aircraft surfaces while offering protection times longer than Type I fluids against refreezing or frozen contamination. The document outlines key performance criteria, such as freezing point, aerodynamic acceptance, and anti-icing performance, alongside environmental properties like biodegradability, aquatic toxicity, biochemical oxygen demand (BOD), and chemical oxygen demand (COD). Operational considerations, including storage stability, materials compatibility, exposure to dry air, dry-out exposure to cold dry air, successive dry-out and rehydration, and physical properties like pH, refraction, and rheological properties (viscosity) are also specified. Additionally, the specification details the required testing methods to evaluate these properties and sets forth
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers a single-component, unfilled, heat-reactive, thermosetting, aromatic system which thermally cures to form a polyimide polymer structure.
This specification covers discontinuously reinforced aluminum alloy (DRA) metal matrix composites (MMC) made by mechanical alloying of the 2124A powder and SiC particulate, which is then consolidated by hot isostatic pressing (HIP) into shapes less than 62 square inches (0.04 m2) in cross-sectional area (see 8.12).
This specification establishes requirements for three types of corrosion preventative coatings for protection of aircraft integral fuel tanks.
This specification covers a corrosion-resistant steel in the form of cold-worked bars and wire up to 1.750 inch (44.45 mm) inclusive, in nominal diameter or least distance between parallel sides (see 8.4).
This specification covers a corrosion-resistant steel in the form of sheet and strip 0.005 inch (0.13 mm) and over in nominal thickness (see 8.7).
The scope of this SAE Aerospace Recommended Practice (ARP) is to establish the procedure for creating titles of aerospace tubing and clamp installation documents generated by SAE Subcommittee G-3E.
This specification covers the requirements for a hard anodic coating on magnesium alloys and the properties of the coating.
This specification covers a magnesium alloy in the form of sand castings (see 8.6).
This SAE Aerospace Standard (AS) establishes the minimum requirements for ground-based aircraft deicing/anti-icing methods and procedures to ensure the safe operation of aircraft during icing conditions on the ground. This document does not specify the requirements for particular aircraft models. The application of the procedures specified in this document are intended to effectively remove and/or prevent the accumulation of frost, snow, slush, or ice contamination which can seriously affect the aerodynamic performance and/or the controllability of an aircraft. The principal method of treatment employed is the use of fluids qualified to AMS1424 (Type I fluid) and AMS1428 (Type II, III, and IV fluids). All guidelines referred to herein are applicable only in conjunction with the applicable documents. Due to aerodynamic and other concerns, the application of deicing/anti-icing fluids shall be carried out in compliance with engine and aircraft manufacturer’s recommendations.
The document provides clarity related to multiple temperature coolant circuits used with on-highway and off-highway, gasoline, and light-duty to heavy-duty diesel engine cooling systems, or hybrid vehicle systems. These multiple temperature systems include engine jacket coolant plus at least one lower temperature system. Out of scope are the low temperature systems used in electric vehicles. This subject is covered in SAE J3073. Note that some content in SAE J3073 is likely to be of interest for hybrid vehicles. Out of scope are the terms and definitions of thermal flow control valves used in either low-temperature or high-temperature coolant circuits. This subject is covered in SAE J3142.
This document covers the dimensional definition of the SAE J3400 (NACS) electric vehicle coupler, which includes the connector and inlet.
This SAE Aerospace Recommended Practice (ARP) establishes general criteria for the installation (e.g., type, location, accessibility, stowage) and crew member training needed for portable fire extinguishers.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
This SAE Recommended Practice describes the dynamic and static testing procedures required to evaluate the integrity of an equipment mount device or system when exposed to a frontal or side impact (i.e., a crash impact). Its purpose is to provide equipment manufacturers, ambulance builders, and end users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure equipment mount devices or systems meet the same performance criteria across the industry. Prospective equipment mount manufacturers or vendors have the option of performing either dynamic testing or static testing. Descriptions of the test setup, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
This specification covers a magnesium alloy in the form of sheet and plate 0.016 to 3.000 inches (0.41 to 76.20 mm) in nominal thickness (see 8.6).
This document recommends standard gland dimensions for static radial O-ring seal applications specifically for engine and engine control systems and provides recommendations for modifying these glands in special applications.
This specification covers an aluminum alloy in the form of plate 3.000 to 6.000 inches (76.20 to 152.40 mm), inclusive, in nominal thickness (see 8.5).
Items per page:
50
1 – 50 of 212293