Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The intent of this specification is for the procurement of plain weave fabric epoxy prepreg product with 250 °F (121 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3).
The intent of this specification is for the procurement of carbon fiber epoxy prepreg product with 250 °F (121 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3).
According to SAE6906, Force Protection and Survivability (FPS) is the Human Systems Integration (HSI) domain that facilitates system operation and personnel safety during and after exposure to hostile situations or environments. Force protection refers to all preventive measures taken to mitigate hostile actions against Department of Defense (DoD) and Department of Homeland Security (DHS) (e.g., U.S. Coast Guard, Customs and Border Patrol, Immigration and Customs Enforcement, etc.) personnel. Survivability denotes the capability of the system and/or personnel manning the system to avoid or withstand man-made hostile environments without suffering an abortive impairment of his/her ability to accomplish its designated mission. Damage due to enemy or fratricidal action, or even equipment failure, will endanger the warfighters' well-being and place them into a life-threatening situation.
This method outlines the standard procedure for testing the hardness of bearing components. Bearings covered by this test method shall be any rolling element bearing used in airframe control.
This SAE Aerospace Recommended Practice (ARP) provides criteria for the design, installation, operation, and training aspects of head-up display (HUD) systems in transport category aircraft, with emphasis on pilot interface and operational requirements. The recommendations apply to permanently installed (including stowable) HUDs that display primary flight information, including those integrating enhanced flight vision system (EFVS) imagery. The intent is to ensure HUDs are designed and used in a manner that improves pilot situational awareness and flight technical performance across all phases of flight, up to and including low-visibility operations. While technical design standards (optical performance, hardware specs, etc.) are defined in documents like ARP5288 and AS8055, this document focuses on pilot usage considerations and human factors. HUD systems addressed here are typically designed to support a fail-passive operational concept applicable to Category III instrument approach
This SAE Aerospace Information Report (AIR) supplements ARP4754B/ED-79B by identifying the crucial elements to be considered when constructing the development assurance plans described in Section 3 (Development Assurance Planning) of ARP4754B/ED-79B for integrated systems. Section 4.6.4 of ARP4754B/ED-79B expands the aircraft/system integration and verification activities by emphasizing testing during integration to investigate for unintended behaviors. However, guidelines are needed for planning that are specifically aimed at the aircraft level and at integrating across system functions and boundaries. Until such guidelines are more comprehensively provided, this AIR presents a collection of lessons learned from past certification programs involving integrated systems, and as such it may be considered in conjunction with Sections 3 and 4 of ARP4754B/ED-79B. ARP4761A/ED-135 elaborates the safety activities by adding processes and methods such as the Aircraft or System Functional Hazard
The purpose of this SAE Recommended Practice is to establish uniform test procedures for measuring and rating air delivery and cooling capacity of truck and off-road self-propelled work machines used in earth moving, agriculture, and forestry air-conditioner evaporator assemblies. It is the intent to measure only the actual cooling capacity of the evaporator. It is not the intent of this document to rate and compare the performance of the total vehicle air-conditioning system.
This SAE Aerospace Information Report (AIR) provides information and guidance for the selection and use of technologies and methods for lubrication system monitoring of gas turbine aircraft engines. This AIR describes technologies and methods covering oil system performance monitoring, oil debris monitoring, and oil condition monitoring. Both on-aircraft and off-aircraft applications are presented. A higher-level view of lubrication system monitoring as part of an overall engine monitoring system (EMS) is discussed in ARP1587. The scope of this document is limited to those lubrication system monitoring, inspection, and analysis methods and devices that can be considered appropriate for health monitoring and routine maintenance. This AIR is intended to be used as a technical guide. It is not intended to be used as a legal document or standard.
This specification covers a titanium alloy in the form of wire for welding filler metal (see 8.5).
This specification covers an aluminum-lithium alloy in the form of extruded profiles 0.040 to 1.000 inch (1.00 to 25.40 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy in the form of castings.
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
This recommended practice describes two methods for determining the tendency of interior materials used in automobiles and other vehicles to (a) produce a light scattering deposit (fog) on a glass surface, or (b) produce a measurable deposit (mass) on aluminum foil.
This specification covers an aluminum alloy in the form of sand castings (see 8.6).
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers an aluminum alloy in the form of sheet 0.040 to 0.249 inch (1.02 to 6.32 mm) in nominal thickness (see 8.7).
This SAE Aerospace Recommended Practice (ARP) document establishes criteria and recommended practices for the use of airborne icing tankers to aid in design and certification of aircraft ice protection systems and components. Several icing tankers are described, along with their capabilities and suggested use. Sample data for these tanker spray systems are included, shown with 14 CFR Parts 25 and 29, Appendix C icing envelopes for continuous maximum and intermittent maximum icing conditions. (Note: In the remainder of this document, the phrase “Appendix C icing envelopes” will be used for brevity.) This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This SAE Information Report establishes procedures and terminology for measuring, calculating, and referencing the percent vehicle overlap for a case vehicle in real-world or staged end plane collisions where the end plane of the case vehicle is engaged at one of the two bumper corners but not both. This SAE Information Report may be applied to rear or front plane impacts.
This document applies to off-road forestry work machines defined in SAE J1116 or ISO 6814.
The process detailed within this document is generic and applies to the entire end-to-end health management capability, covering both on-board and on-ground elements, in both commercial and military applications throughout their lifecycle. This ARP addresses a gap in guidance related to usage of ground-based health management equipment for airworthiness credit, ensuring a level of integrity commensurate with the potential aircraft-level consequences of the relevant failure conditions. The practical application of this standardized process is detailed in the form of a checklist. The on-board elements described here are typically the source of the data acquisition used for off-board analysis. The on-board aspects relating to airworthiness and/or safety of flight, e.g., pilot notification, are addressed by existing guidance and policy documents. If a proposed health management capability for airworthiness credit involves modification of the on-board systems, the substantiation of those
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull. It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.
This document describes a rigorous engineering test procedure that utilizes industry-accepted data collection and statistical analysis methods to determine the road load and to estimate the aerodynamic drag area of trucks and buses weighing more than 10000 pounds. The test procedure may be conducted on a test track or on a public road under controlled conditions and supported by extensive data collection and data analysis constraints. The estimated aerodynamic-drag-area result represents a single-speed and single-yaw-angle condition. Test results that do not rigorously follow the method described herein shall not be represented as an SAE J2978 result.
This specification covers an aluminum alloy in the form of sheet from 0.020 to 0.249 inch (0.51 to 6.32 mm), inclusive, in thickness (see 8.6).
This specification covers a corrosion- and heat-resistant steel in the form of investment castings.
This SAE Standard applies to machines as defined in Appendix A. Some of these machines can travel on-highway but function primarily off-highway.
This specification covers a titanium alloy in the form of sheet 0.025 through 0.100 inch (0.63 through 2.54 mm), inclusive, in thickness (see 8.6).
This SAE Standard applies to refrigerant diagnostic identification equipment to be used for identifying refrigerant HFC-134a (R-134a) and HFO-1234yf (R-1234yf) refrigerant when servicing a mobile A/C system or for identifying refrigerant in a container to be used to charge a mobile A/C system. Identification of other refrigerants is the option of the equipment manufacturer, although it shall not misidentify refrigerants, per 3.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification establishes hardness and electrical conductivity acceptance criteria for finished or semifinished parts made from wrought aluminum alloys after heat treatment (see 8.6).
The thermocouple design recommended herein is presented as one for which the correction to the observed emf, because of thermal conduction along the stem and wires, is within the limits presented in the accompanying figure. On referring to the figure, it is seen that no restriction is placed upon the diameter of the thermocouple or stem, and the longitudinal dimensions are expressed in terms of wire and stem diameters. The type of stem, such as packed ceramic stock, refractory insulating tubing, etc., also is left open to choice. Thus the sizes of wires and supporting stems may be varied over wide ranges to match particular requirements where conduction errors are to be limited or controlled.
This SAE Standard is intended to describe the basic types of felling heads, including those with bunching capabilities, that are attachments to a self-propelled machine. Only the major components that are necessary to describe the functions of the felling head, and to apply the principles of the standard are included. Illustrations used are not intended to include all existing felling heads or to describe any particular manufacturer’s variation.
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems aboard commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards. SAE J1942-1 is a listing of the products which have been certified for use in
Procurement specification is principally for defining protection sleeves on a cable or group of electrical/fiber optic wires (wiring bundle). Single wire protection depends on the minimum diameter of the wire. Sleeve may be used to protect a wire bundle for a platform installation or for repair of installed damaged jacket or jacket/shielded wire bundles. Refer to AS50881 for aerospace wire bundle protection installations.
Items per page:
50
1 – 50 of 219468