Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report. Because this is an Information Report, the numerical values for performance measurements presented in this report and
This SAE Recommended Practice is intended to provide basic information on properties and characteristics of high-strength carbon and alloy steels which have been subjected to special die drawing. This includes both cold drawing with heavier-than-normal drafts and die drawing at elevated temperatures.
This SAE Recommended Practice provides a standard procedure for testing the output performance and plotting the performance curve of air starting motors.
This SAE Recommended Practice identifies some basic and general conditions that should be considered when making electrical starter motor applications.
This SAE Aerospace Standard (AS) provides the method for presentation of gas turbine engine steady-state and transient performance calculated using computer programs. It also provides for the presentation of parametric gas turbine data including performance, weight, and dimensions computed by computer programs. This standard is intended to facilitate calculations by the program user without unduly restricting the method of calculation used by the program supplier. This standard is applicable, but not limited to, the following program types: data reduction, steady-state, transient, preliminary design, study, specification, status, and parametric programs.
This recommended practice is derived from common test sequences used within the industry. This procedure applies to all on-road passenger cars and light trucks up to 4 540 kg of GVWR. This recommended practice does not address other aspects such as performance, NVH, and durability. Test results from this recommended practice should be combined with other measurements and dynamometer tests (or vehicle-level tests), and acceptance criteria to validate a given design or configuration.
This document derives from the Federal Motor Vehicle Safety Standards (FMVSS) 105 and 135 vehicle test protocols as single-ended inertia-dynamometer test procedures. The test sequences enable brake output measurement, friction material effectiveness, and corner performance in a controlled and repeatable environment. This SAE Document also includes optional sections for parking brake output performance for rear brakes with hydraulic or Electric Park Brakes (EPB). It applies to brake corners from vehicles covered by the FMVSS 105 and 135 when using the appropriate brake hardware and test parameters. The FMVSS 135 applies to all passenger cars and light trucks up to 3500 kg of gross vehicle weight (GVWR). The FMVSS 105 applies to all passenger cars, multi-purpose vehicles, buses, and trucks above 3500 kg of GVWR. This document does not include testing for school bus applications or vehicles equipped with hydraulic brakes with a GVWR above 4540 kg. This document does not evaluate or
In this report, "Cryogenically Fueled Dynamic Power Systems" include all open cycle, chemically fueled, dynamic engine power systems which utilize cryogenic fuels and oxidizers. For nearly all practical present day systems, this category is limited to cryogenic hydrogen or hydrogen-oxygen fueled cycles with potential in future, more advanced systems for replacement of oxygen by fluorine. Excluded from the category are static cryogenic systems (e.g., fuel cells) and chemical dynamic power systems which utilize earth storable propellants.
This technical report identifies the requirements for an LFCP for ADHP soldered electronic products built fully or partially with Pb-free materials and assembly processes. An LFCP documents the specific Pb-free materials and assembly processes used to assure customers their ADHP soldered electronic products will meet the applicable reliability requirements of the customer. This standard specifically addresses LFCPs for: a Pb-free components and mixed assembly: Products originally designed and qualified with SnPb solder and assembly processes that incorporate components with Pb-free termination finishes and/or Pb-free BGAs, i.e., assembling Pb-free parts using eutectic/near-eutectic SnPb processes (also known as mixed metallurgy). b COTS products: COTS products likely built with Pb-free materials and assembly processes. c Pb-free design and assembly: Products designed and qualified with Pb-free solder and assembly processes. This standard does not include detailed descriptions of the
The purpose of this document is to establish air-conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system; since these characteristics and conditions vary greatly from one application to another, the designer shall determine the goals expected to be reached under the conditions encountered. To determine the capacity of such items as blowers, condenser fans, condenser coils, evaporator coils, filters, compressors, etc., will require the adherence to several guidelines, some of which are outlined in the following paragraphs.
This procurement specification covers aircraft quality self-locking nuts for wrenching (hex, spline) and anchor (plate, gang channel, shank) types of nuts made from a corrosion and heat-resistant nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. Tension height nuts having overall length of threaded portion not less than 1.2 times the nominal thread diameter have 1210 MPa minimum tensile strength at room temperature. Shear height nuts having shorter threaded portion have 1100 MPa minimum tensile strength at room temperature. Maximum test temperature of parts is 730 °C.
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a Ability of the parking brake system to lock the braked wheels. b The trailer holding or sliding on the grade, fully loaded, or unloaded. c Applied manual effort. d Unburnished or burnished brake lining friction conditions. e Down and upgrade directions.
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
This report is concerned with factors which affect accuracy of distance indication and speed indication of automotive type odometer speedometers. It is the intent to supply information regarding all items which affect the instrument.
This procurement specification covers alloy steel and corrosion and heat resistant steel free running metric nuts of the following types, styles and classes.
This SAE Recommended Practice describes common definitions and operational elements of Event Data Recorders. The SAE J1698 series of documents consists of the following: SAE J1698-1 - Event Data Recorder - Output Data Definition: Provides common data output formats and definitions for a variety of data elements that may be useful for analyzing vehicle crash and crash-like events that meet specified trigger criteria. SAE J1698-2 - Event Data Recorder - Retrieval Tool Protocol: Utilizes existing industry standards to identify a common physical interface and define the protocols necessary to retrieve records stored by light duty vehicle Event Data Recorders (EDRs). SAE J1698-3 - Event Data Recorder - Compliance Assessment: Defines procedures that may be used to validate that relevant EDR output records conform with the reporting requirements specified in Part 563, Table 1 during the course of FMVSS-208, FMVSS-214, and other applicable vehicle level crash testing.
This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control.
This SAE Standard describes head position contours and procedures for locating the contours in a vehicle. Head position contours are useful in establishing accommodation requirements for head space and are required for several measures defined in SAE J1100. Separate contours are defined depending on occupant seat location and the desired percentage (95 and 99) of occupant accommodation. This document is primarily focused on application to Class A vehicles (see SAE J1100), which include most personal-use vehicles (passenger cars, sport utility vehicles, pick-up trucks). A procedure for use in Class B vehicles can be found in Appendix B.
This information report is intended to give general data on the properties of aluminum and information on working, joining, forming, machining, finishing, and heat treating of aluminum.
Items per page:
50
1 – 50 of 219709