Results
This procedure is intended to apply to fuel pumps. This procedure will be defined in terms of recommended test fluid, test setup, test conditions, and test method. This procedure may be used for other fuel system components, by testing in conjunction with the pump, which normally supplies the component inlet flow, or a substitute test pump of similar capacity. This procedure may be used, with variations in test conditions and test fluid, for performing pump evaluation tests. Tests at progressively increasing pump speeds and pressures will provide design limitation data. Alternate test periods on a test pump and another pump, of a design for which actual service durability is known, will provide useful comparison data
This document specifies the procedure and requirements for gas nitriding steel parts by the use of raw or dissociated ammonia
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, and forgings 7.0 inches (178 mm) and under in nominal diameter or least distance between parallel sides, and forging stock of any size
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, and seal. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W
This specification covers the procedures for approval of products of premium-quality titanium alloys and the controls to be exercised in producing such products
This specification covers a titanium alloy in the form of bars up through 6.000 inches (152.40 mm), inclusive, in nominal diameter or least distance between parallel sides, forgings of thickness up through 6.000 inches (152.40 mm), inclusive, and stock for forging of any size (see 8.6
This specification, in conjunction with the general requirements for peening media covered in AMS2431, establishes the requirements for the procurement of conditioned carbon steel cut wire shot with a hardness of 45 to 52 HRC
This specification, in conjunction with the general requirements for peening media covered in AMS2431, establishes the requirements for the procurement of conditioned carbon steel cut wire shot with a hardness of 55 to 62 HRC
This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm) in nominal diameter or least distance between parallel sides, inclusive, forgings of thickness up through 4.000 inches (101.60 mm), inclusive, and stock for forging of any size (see 8.6
This specification covers a corrosion- and heat-resistant nickel alloy in the form of wire up to and including 0.563 inches (14.30 mm) in diameter
This specification, in conjunction with the general requirements for peening media covered in AMS2431, establishes the requirements for the procurement of conditioned stainless steel cut wire shot
This specification covers an aluminum alloy procured in the form of extruded bars, rods, wire, profiles (shapes), and tubing up to 1.499 inches (38.07 mm), inclusive, in nominal diameter or least thickness (bars, rods, wire, or profiles) or nominal wall thickness (tubing) (see 8.6
The complete requirements for procuring the product shall consist of this document and the latest Issue of the basic specification, AMS2431
This SAE Standard describes a reference system architecture based on LTE-V2X technology defined in the set of ETSI standards based on 3GPP Release 14. It also describes cross-cutting features unique to LTE-V2X PC5 sidelink (mode 4) that can be used by current and future application standards. The audience for this document includes the developers of applications and application specifications, as well as those interested in LTE-V2X system architecture, testing, and certification
This specification covers the requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating
This specification covers aircraft-quality, low-alloy steel in the form of round, seamless tubing
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This document presents criteria for design and location of passenger reading lights in commercial aircraft. For LED reading light requirements, see ARP5873, titled: LED Passenger Reading Light Assembly
This SAE Aerospace Recommended Practice (ARP) recommends the design and features of aircraft demonstration emergency equipment for use in passenger safety briefings
This SAE Aerospace Standard (AS) defines implementation requirements for the electrical interface between: a Aircraft carried miniature store carriage systems and miniature stores b Aircraft parent carriage and miniature stores c Surface-based launch systems and miniature stores The interface provides a common interfacing capability for the initialization and employment of smart miniature munitions and other miniature stores from the host systems. Physical, electrical, and logical (functional) aspects of the interface are addressed
This specification covers a corrosion- and heat-resistant, work strengthened cobalt-nickel-chromium alloy in the form of bars 2 inches (50 mm) and under in nominal diameter
This SAE Aerospace Standard (AS) defines minimum standards of design, construction, and performance for two types of permanently installed, high pressure 12,800 kPa (1850 psig) and 13,800 kPa (2000 psig) oxygen system cylinder fill valves used in commercial aircraft. Refer to Purchaser's Specification for Requirements which are beyond the scope or level of detail provided in this document. One valve has an adjustable pressure sensitive closing valve to automatically control the final pressure for a correct amount of oxygen in the system. The second valve incorporates an automatic shutoff feature designed to limit system overpressurization in the event maintenance personnel do not stop system filling at the correct pressure. The intent of the fill valves is to control the rate of fill to limit the rise in temperature caused by compression heating to acceptable values, prevent oxygen back flow and prevent the ingestion of foreign matter that could cause contamination of the system. Note
This SAE Aerospace Recommended Practice (ARP) provides design, operation, construction, test and installation recommendations for equipment that automatically presents supplemental oxygen masks to cabin occupants in the event of loss of cabin pressure. It specifically covers automatic presentation for transport category aircraft that operate above 30 000 ft (9144 m) altitude. It also provides guidance for similar equipment used in non-transport category aircraft, or aircraft operated below 30 000 ft (9144 m) altitude
This SAE Aerospace Recommended Practice (ARP) provides a guide for preparation of requirements for general design, performance, and testing of mechanical geared rotary actuators intended to be used for applications requiring motion control in response to manual or automatic power control system inputs
This document is intended for use during audits to the requirements of AS5553C. It may be used by all contracting organizations that procure EEE parts, whether such parts are procured directly or integrated into electronic assemblies or equipment as guidance for evaluating compliance to AS5553C
This SAE Aerospace Standard (AS) establishes the requirements for straight threaded boss or flanged fluid connection fittings (see Section 6) for use in all types of fluid systems
This SAE Recommended Practice covers the most common applications of electronically controlled on-demand clutch systems used in passenger (car and light truck) vehicle applications. This practice is applicable for torque modulation devices used in transfer cases, electronic limited slip differential (eLSD) cross-axle devices, rear drive module (RDM) integrated torque transfer devices with or without disconnect capability, and other related torque transfer devices
This SAE Aerospace Recommended Practice (ARP) is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances
Items per page:
50
1 – 50 of 208765