Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This document covers insulated, flexible air duct assemblies for portable ground support air conditioners and heaters.
This SAE Aerospace Standard (AS) provides a method for gas turbine engine performance computer programs to be written using Fortran COMMON blocks. If a “function-call application program interface” (API) is to be used, then ARP4868 and ARP5571 are recommended as alternatives to that described in this document. When it is agreed between the program user and supplier that a particular program shall be supplied in Fortran, this document shall be used in conjunction with AS681 for steady-state and transient programs. This document also describes how to take advantage of the Fortran CHARACTER storage to extend the information interface between the calling program and the engine subroutine.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This slash document collects general reference material related to gaseous oxygen system flow requirements and sizing calculations. This document will assist oxygen system equipment designers and operators to establish systems and equipment requirements. The document consists of charts, tables, system schematics, system requirements, and sample calculations for system sizing.
This SAE Aerospace Standard (AS) offers gland details for a 0.364 inch (9.246 mm) cross-section gland (nominal 3/8 inch) with proposed gland lengths for compression-type seals with two backup rings over a range of 7 to 21 inches (178 to 533 mm) in diameter. The dash number system used is similar to AS568A. A 600 series has been chosen as a logical extension of AS568A, and the 625 number has been selected for the initial number, since 300 and 400 series in MIL-G-5514 and AS4716 begin with 325 and 425 sizes. Seal configurations and design are not a part of this document. This gland is for use with compression-type seals including, but not limited to, O-rings, T-rings, D-rings, cap seals, etc.
The primary purpose of the shipping closure is to protect the aircraft parts or system from damage and foreign material ingress/egress (e.g., dust, dirt or other contaminants) during transport and storage. Shipping closures are not airworthy items. Therefore, their usage is defined as preventative for the parts to be protected as opposed to operational. Military and commercial customer requirements for the prevention of damage or contamination to stored parts are generally limited to the generic instructions “all openings should be sufficiently covered to prevent the entrance of dust, dirt, moisture or other foreign contaminants”. This recommended practice outlines basic minimum parameters for suggested item construction and usage. Additionally, this recommended practice provides instruction on how to apply these closures to various openings.
This document outlines the evaluation and documentation appropriate when the components of an approved aircraft seat restraint system are replaced or modified by a party other than the Original Equipment Manufacturer of the restraint system.
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
This specification defines the requirements for a grooved clamp coupling and flanges suitable for joining intermediate pressure and temperature ducting in aircraft air systems. The rigid coupling joint assembly, hereafter referred to as "the joint", shall operate within the temperature range of -65 °F to +800 °F.
This document establishes the Rotorcraft Industry Technology Association (RITA) Health and Usage Monitoring System Data Interchange Specification. The RITA HUMS Data Interchange Specification will provide information exchange within a rotorcraft HUMS and between a rotorcraft HUMS and external entities.
This SAE Aerospace Standard (AS) covers the general requirements for the design, manufacture, and test of 28 VDC, 270 VDC, and 115 VAC solid-state power controllers (SSPCs) for use in electrical power systems. SSPCs conforming to this standard are intended for use in controlling the making and breaking of power circuits for electrically operated equipment and devices, and for providing overload and short-circuit protection. Applications that require SSPCs to have a high level of performance in some areas or may be exposed to harsher electrical or environmental conditions are designated as CLASS A. Applications that utilize SSPCs in moderate level of performance or are exposed to a controlled environment are designated as CLASS C. Applicability of both MIL-STD-704 and RTCA DO-160G have been considered when determining the performance standards for the designated classes of SSPCs. To support older aircraft platforms, legacy versions of these specifications were also considered as
This test method outlines the recommended procedure for performing dimensional stability tests on rolling element bearings used in airframe applications. Bearings covered by this document shall be antifriction ball bearings and spherical roller bearings with through-hardened outer rings.
Items per page:
50
1 – 50 of 219717