Results
This SAE Aerospace Information Report (AIR) discusses past and present approaches for monitoring the landing gear structure and shock absorber (servicing), opportunities for corrosion detection, methods for transient overload detection, techniques for measuring the forces seen by the landing gear structure, and methods for determining the fatigue state of the landing gear structure. Landing gear tire condition and tire pressure monitoring are detailed in ARP6225, AIR4830, and ARP6137, respectively. Aircraft Brake Temperature Monitoring Systems (BTMS) are detailed in AS1145.
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This document derives from the Federal Motor Vehicle Safety Standards (FMVSS) 105 and 135 vehicle test protocols as single-ended inertia-dynamometer test procedures. The test sequences enable brake output measurement, friction material effectiveness, and corner performance in a controlled and repeatable environment. This SAE Document also includes optional sections for parking brake output performance for rear brakes with hydraulic or Electric Park Brakes (EPB). It applies to brake corners from vehicles covered by the FMVSS 105 and 135 when using the appropriate brake hardware and test parameters. The FMVSS 135 applies to all passenger cars and light trucks up to 3500 kg of gross vehicle weight (GVWR). The FMVSS 105 applies to all passenger cars, multi-purpose vehicles, buses, and trucks above 3500 kg of GVWR. This document does not include testing for school bus applications or vehicles equipped with hydraulic brakes with a GVWR above 4540 kg. This document does not evaluate or
This SAE Standard applies to equipment to be used with R-1234yf refrigerant only. It establishes requirements for equipment used to recharge R-1234yf to an accuracy level that meets Section 9 of this document and purity levels defined in SAE J2099. Refrigerant service equipment is required to ensure adequate refrigerant recovery to reduce emissions and provide for accurate recharging of mobile air-conditioning systems. Equipment shall be certified to meet all performance requirements outlined in this document and international/regional construction and safety requirements as outlined in this document.
This Standard is restricted to refrigeration circuits that provide air-conditioning for the passenger compartments of passenger and commercial vehicles. This Standard includes analytical and physical test procedures to evaluate refrigerant concentration inside the passenger compartment. In the early phases of vehicle evaluation, usage of the analytical approach may be sufficient without performing physical tests. The physical test procedure involves releasing refrigerant from an external source to a location adjacent to the evaporator core (inside the HVAC module). An apparatus is used to provide a repeatable, calibrated leak rate. If the system has multiple evaporators, leakage could be simulated at any of the evaporator locations. This standard gives detail information on the techniques for measuring R-744 (CO2) and R-1234yf (HFO-1234yf), but the general techniques described here can be used for other refrigerants as well.
The SAE system of designating steels, described in SAE J402, classifies and numbers them according to chemical composition. In the case of the dent resistant, high strength and ultra high strength steels in SAE J2340, advanced high strength steels described in SAE J2745, and the high strength steels in SAE J1442 and the high-strength carbon and alloy die drawn steels in SAE J935, minimum mechanical property requirements have been included in the designations. In addition, hardenability data on most of the alloy steels and some of the carbon steels will be found in SAE J1268.
This test is designed to measure the thickness of textiles, plastics, and similar materials.
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling, and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling oxygen cylinders while installed on aircraft, directly or through an intermediate charging port.
The specification covers a titanium alloy in the form of wire (see 8.5).
This SAE Standard applies to the application of ultraviolet leak detection to service mobile air-conditioning systems.
The scope of this SAE Recommended Practice is to establish uniform test procedures for passenger cars, to determine whether the system is defined as a defroster or defogger, and to establish minimum performance requirements for each system. A defroster for purposes of this practice is a system which will remove moisture and/or frost from the interior surface of the backlight at −18 °C. A defogger is a system which will remove moisture and/or fog from the interior surface of the backlight at 4 °C. The test procedure is intended to simulate actual conditions by utilizing either a cold room with an appropriate device to introduce air flow over the backlight or a sufficiently large wind tunnel with ambient temperature control. The test procedure and the minimum performance requirements are based on currently available engineering data.
This SAE Standard applies to refrigerant vapor compression systems that provide cooling and/or heating for passenger cars, light trucks, and commercial vehicles (on and off road) that use automotive type mobile air conditioning (MAC) systems. Large trucks, buses, and other vehicles that do not use typical automotive A/C systems or use refrigerants not listed in this document are not covered by this standard. This standard covers vehicles with MAC systems using belt driven compressors and electric motor driven compressors. This document provides industry-recognized standards for the design, assembly, and test of MAC systems, including necessary service equipment, and is intended to cover all phases of the lifetime of MAC systems to minimize environmental, health, and safety impacts. The standards listed in this document cover the currently accepted industry guidelines and procedures. The standards can be used as requirements for regulatory authorities to meet minimum environmental
This SAE Aerospace Recommended Practice (ARP)4294 is directed at life cycle cost (LCC) analysis of aerospace propulsion systems and supplements AIR1939. Specific topics addressed by ARP4294 are listed below: a Propulsion system LCC element structure. b Information exchange and relationships with: (1) Aircraft manufacturer (2) Equipment suppliers (3) Customer c The relationship of the LCC element structure to work breakdown structures. d The relationship between LCC analysis and other related disciplines (e.g., technical (performance analysis, weight control, component lives), reliability, availability and maintainability (RAM), integrated logistic support (ILS), production and finance). e Classification of the accuracy and applicability of LCC assessments.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
The purpose of this SAE Standard is to provide equipment specifications for CFC-12 (R-12) recycling equipment. This information applies to equipment used to service automobiles, light trucks, and other vehicles with similar CFC-12 (R-12) air-conditioning (A/C) systems. Systems used on mobile vehicles for refrigerating cargo that have hermetically sealed systems are not covered in this document. The equipment in this document is intended for use with refrigerant that has been directly removed from, and intended to be returned to, a mobile A/C system. Should other revisions due to operational or technical requirements occur, this document may be amended.
This SAE Recommended Practice provides general guidelines for measuring the splash and spray produced by vehicles operating over wet pavements. The guidelines describe both the video digitizing and the laser methods of analysis. The video-digitizing method uses video images and contrast measurements between black and white checkerboards when a spray cloud is superimposed on them as a means of measuring the obscuring spray. The laser method uses laser transmittance through the spray cloud as the means of measurement. It is left to the users of this practice to decide which method is best suited to their needs. There is no implied relationship between these two methods, although it is expected that the ranking of relative spray reduction between test vehicle configurations would be approximately the same. All sections listed in this document are to be considered as common to both methods, unless otherwise noted. There are complex interactions of variables that affect splash and spray
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This SAE Aerospace Recommended Practice (ARP) defines the test set-up requirements, general analysis procedures, and test report documentation for impact tests where photometric analysis of the high speed film or digital video will be required to obtain target paths (typically the Anthropomorphic Test Dummy (ATD) head path and knee path). Such tests support the requirements of AS8049 - Performance Standard for Seats in Civil Rotorcraft, Transport Aircraft and General Aviation Aircraft. These setup and analysis procedures are applicable to conventional, geometry based, two-dimensional analysis. If a more sophisticated technique that allows cameras to be installed at oblique angles for two or three-dimensional analysis is used, then the specific procedures required by that technique supersede any conflicting procedures contained herein. Some of the requirements that could be superseded include camera placement, optical data channel evaluation, camera to subject measurements, and scaling
To define capabilities and limitations of Raman spectroscopy as it pertains to counterfeit detection of EEE parts and suggest possible applications to these ends. Additionally, this document outlines requirements associated with the application of Raman spectroscopy including: Operator training; Sample preparation; Data interpretation; Computerized spectral matching including pass/fail criteria; Equipment maintenance and; Reporting of data. If AS6171/8 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
This document describes an assessment of the effectiveness of a specified test plan used to screen for counterfeit parts. The assessment includes the determination of the types of defects detected using a specified test plan along with the related counterfeit type coverage. The output of this evaluation will produce Counterfeit Defect Coverage (CDC), Counterfeit Type Coverage (CTC), Not-Covered Defects (NCDs), and Under-Covered Defects (UCDs). This information will be supplied to the test laboratory’s customer in both the test report and the Certificate of Quality Conformance (CoQC). This evaluation method does not address the effectiveness of detecting tampered type devices. The Test Evaluation Method also describes an Optimized Test Sequence Selection, in which a test sequence is selected that maximizes the CDC utilizing test cost and time as constraints, for any tier level except the Critical Risk Level. The constraints can be adjusted until the desired CDC is achieved. The output
This specification covers a silicone (VMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This Technical Governance is part of the SAE UCS Architecture Library and is primarily concerned with the UCS Architecture Model (AS6518) starting at Revision A and its user extensions. Users of the Model may extend it in accordance with AS6513 to meet the needs of their UCS Products. UCS Products include software components, software configurations and systems that provide or consume UCS services. For further information, refer to AS6513 Revision A or later. Technical Governance is part of the UCS Architecture Framework. This framework governs the UCS views expressed as Packages and Diagrams in the UCS Architecture Model.
This specification covers tubular-shaped pins, fabricated from carbon steel, having a full-length longitudinal slot to permit flexure when inserted into a hole.
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
The intent of this specification is for the procurement of the material listed on the QPL and, therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program shall refer to the Quality Assurance section of the base specification, AMS3961. All material qualification and equivalency data has been archived and is available for review upon request. Contact the CMH-17 Secretariat (www.cmh17.org) for additional information.
The supplier shall use the following process to respond to a customer request for corrective and preventive action.
Items per page:
50
1 – 50 of 222744