Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for backup/reversing lamp.
This document provides design guidelines, test procedure references, and performance requirements for omnidirectional and selective coverage optical warning devices used on authorized emergency, maintenance, and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
This document addresses robustness of electrical/electronic modules for use in automotive applications. Where practical, methods of extrinsic reliability detection and prevention will also be addressed. This document primarily deals with electrical/electronic modules (EEMs), but can easily be adapted for use on mechatronics, sensors, actuators and switches. EEM qualification is the main scope of this document. Other procedures addressing random failures are specifically addressed in the CPI (Component Process Interaction) section 10. This document is to be used within the context of the Zero Defect concept for component manufacturing and product use. It is recommended that the robustness of semiconductor devices and other components used in the EEM be assured using SAE J1879 OCT2007, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications. The emphasis of this document is on hardware and manufacturing failure mechanisms, however, other contemporary issues
The methods included in this document are: a Voltage-Temperature Design Margins. b Voltage Interruptions and Transients. c Voltage Dropouts and Dips. d Current Draw Under a Number of Conditions. e Switch Input Noise These methods are best applied during the Development stage but can be used at all stages (e.g., Pre-Qualification, Qualification or Conformity).
This SAE Standard provides a general method for defining the acceptable function performance status classification for the functions of automotive electronic devices upon application of the test conditions specified as described in appropriate EMC immunity test standards (for example, SAE J1113 and SAE J551). Testing of devices could be performed either on or off vehicles. Appropriate test signal and methods, Function Performance status, and test signal severity level would have to be specified in the individual cases.
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/E Diagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics – Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
This SAE Information Report defines a procedure for indicating the severity of narrowband emissions from an electronic system-component.
This SAE Standard specifies the test methods and procedures necessary to evaluate electrical components intended for automotive use to the threat of Electrostatic Discharges (ESDs). It describes test procedures for evaluating electrical components on the bench in the powered mode and for the packaging and handling non-powered mode. A procedure for calibrating the simulator that is used for electrostatic discharges is given in Appendix A. An example of how to calculate the RC Time Constant is given in Appendix B Functional Performance Status Classifications for immunity to ESD and Sensitivity classifications for ESD sensitive devices are given in Appendix C.
This SAE Recommended Practice provides supporting information for the emission and immunity measurement procedures defined in the SAE J1752 series of documents.
This SAE Information Report identifies and defines the preferred technical guidelines relating to safety for vehicles that contain High Voltage (HV), such as Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), Plug-In Hybrid Electric Vehicle (PHEV), Fuel Cell Vehicles (FCV) and Plug-In Fuel Cell Vehicles (PFCV) during normal operation and charging, as applicable. Guidelines in this document do not necessarily address maintenance, repair, or assembly safety issues.
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/EDiagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics - Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU. It further specifies additional
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECUs) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. U.S. Environmental Protection Agency (EPA) and the California Air Resources
This SAE Recommended Practice defines the requirements of OBD II Scan Tools, i.e., test equipment that will interface with vehicle modules in support of the OBD II diagnostic requirements. It covers the required capabilities of and conformance criteria for OBD II Scan Tools.
This SAE Recommended Practice is applicable to all light-duty and medium-duty passenger vehicles and trucks with feedback fuel control system. Specific applications of this document include diagnostic, service and repair manuals, repair databases, and off-board readout devices. This document focuses on a diagnostic code format and code messages for automotive electronic control systems. The use and appropriate updating of this document is strongly encouraged; however, this document does not prohibit the use of additional codes for additional diagnostics.
This SAE Recommended Practice defines the test conditions, procedures, and performance specifications for 6- and 12-v stop lamp switches intended for use on motorcycles.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
This SAE Standard establishes test methods for the evaluation of devices and equipment in vehicles against transient transmission by coupling via lines other than the power supply lines. The test methods demonstrates the immunity of the instrument, device, or equipment to coupled fast transient disturbances, such as those caused by switching of inductive loads, relay contact bouncing, etc. Four test methods are presented in SAE J1113-12: the capacitive coupling clamp (CCC) method the direct capacitive coupling (DCC) method the inductive coupling clamp (ICC) method the capacitive/inductive coupling (CIC) method
Vehicle electrical/electronic systems may be affected when immersed in an electromagnetic field generated by sources such as radio and TV broadcast stations, radar and communication sites, mobile transmitters, cellular phones, etc. This part of SAE J551 specifies off-vehicle radiated source test methods and procedures for testing passenger cars and commercial vehicles within a Reverberation Chamber. The method is used to evaluate the immunity of vehicle mounted electronic devices in the frequency range of 80 MHz to 2 GHz, with possible extensions 20 MHz to 10 GHz, depending upon chamber size and construction. Three methods for calibrating and applying electromagnetic fields are described in the document: 1) Mode Tuned Reverberation Chamber method, 2) Mode Stir (Standard) Reverberation Chamber method and 3) Mode Stir (Hybrid) Reverberation Chamber method. Optional pulse modulation testing at HIRF (High Intensity Radiated Fields) test levels, based upon currently known environmental
This SAE Standard defines methods and apparatus to evaluate electronic devices for immunity to potential interference from conducted transients along battery feed or switched ignition inputs. Test apparatus specifications outlined in this procedure were developed for components installed in vehicles with 12-V systems (passenger cars and light trucks, 12-V heavy-duty trucks, and vehicles with 24-V systems). Presently, it is not intended for use on other input/output (I/O) lines of the device under test (DUT).
This SAE Standard specifies the ESD test methods and procedures necessary to evaluate electronic modules intended for vehicle use. It describes test procedures for evaluating electronic modules in complete vehicles. A procedure for verifying the simulator that is used to generate the electrostatic discharges is given in Appendix A. Functional status classifications for immunity to ESD are given in Appendix B.
This document contains a "sample" Control Plan with explanations as to the intended content of various sections. It also can serve as a sample technical construction file as specified by the European EMC Directive.
This AIR was prepared to inform the aerospace industry about the electromagnetic interference measurement capability of spectrum analyzers. The spectrum analyzers considered are of the wide dispersion type which are electronically tuned over an octave or wider frequency range. The reason for limiting the AIR to this type of spectrum analyzer is that several manufacturers produce them as general-purpose instruments, and their use for EMI measurement will give significant time and cost savings. The objective of the AIR is to give a description of the spectrum analyzers, consider the analyzer parameters, and describe how the analyzers are usable for collection of EMI data. The operator of a spectrum analyzer should be thoroughly familiar with the analyzer and the technical concepts reviewed in this AIR before performing EMI measurements.
This document contains a "sample" Control Plan with explanations as to the intended content of various sections. It also can serve as a sample technical construction file as specified by the European EMC Directive.
This document provides design guidelines, test procedure references, and performance requirements for directional, single color, flashing optical warning devices used on authorized emergency, maintenance and service vehicles. It is intended to apply to, but not limited to, surface land vehicles.
This SAE Recommended Practice covers the recommended testing techniques for the determination of electric field immunity of an automotive electronic device when the device and its wiring harness is exposed to a power line electric field. This technique uses a parallel plate field generator and a high voltage, low current voltage source to produce the field.
This SAE Aerospace Recommended Practice outlines a standardized and economical method for the checkout and calibration of electromagnetic interference measurement antennas. Its application is for use when measuring a source 1 m from the antenna in a shield room. This is the typical distance used in performing military EMC testing. The influence of the shield room on the measured field strength is not considered. This standard does not address the measurement of emissions from an unknown distributed source, yet it attempts to resemble reality by using another antenna, in the calibration method, that represents a distributed source. This document presents a technique to determine antenna factors for antennas used primarily in performing measurements in accordance with References 2.1 and 2.2. The purpose of Revision B was to include the calibration of other antennas, such as biconical, horn, monopole and small loop antennas that are also specified for use in these same references
This SAE Recommended Practice covers the recommended testing techniques for the determination of electric field immunity of an automotive electronic device when the device and its wiring harness is exposed to a power line electric field. This technique uses a parallel plate field generator and a high voltage, low current voltage source to produce the field.
To define test cases for the OBD-II interface on external test equipment (such as an OBD-II Scan Tool, Inspection/Maintenance Tester, etc.) which can be used to verify compliance with the applicable standards such as SAE J1978 and SAE J1979 for Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles and Engines (OBD II).
This SAE Recommended Practice will define the Physical Layer and portions of the Data Link Layer of the Open Systems Interconnection model (ISO 7498) for a 500 kbps High-Speed CAN (HSC) protocol implementation. Both ECU and media design requirements for networks will be specified. Requirements will primarily address the CAN physical layer implementation. Requirements will focus on a minimum standard level of performance from the HSC implementation. All ECUs and media shall be designed to meet certain component level requirements in order to ensure the HSC implementation system level performance at 500 kbps. The minimum performance level shall be specified by system level performance requirements or characteristics described in detail in Section 5 of this document. This document is designed such that if the Electronic Control Unit (ECU) requirements defined in Section 6 are met, then the system level attributes should be obtainable. This document will address only requirements which may
This SAE Recommended Practice is applicable to all light-duty and medium-duty passenger vehicles and trucks with feedback fuel control system. Specific applications of this document include diagnostic, service and repair manuals, repair databases, and off-board readout devices. This document focuses on a diagnostic code format and code messages for automotive electronic control systems. The use and appropriate updating of this document is strongly encouraged; however, this document does not prohibit the use of additional codes for additional diagnostics.
This document supersedes SAE J1962 200204, and is technically equivalent to ISO/DIS 15031-3: December 14, 2001. This document is intended to satisfy the requirements of an OBD connector as required by U.S. On-Board Diagnostic (OBD) regulations. The diagnostic connection specified in this document consists of two mating connectors, the vehicle connector and the external test equipment connector. This document specifies: a The functional requirements for the vehicle connector. These functional requirements are separated into four principal areas: connector location/access, connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits, b The functional requirements for the external test equipment connector. These functional requirements are separated into three principal areas: connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits.
SAE J2534-1 defines a standard vehicle network interface that can be used to reprogram emission-related control modules. However, there is a need to support vehicles prior to the 2004 model year, as well as non-emission related control modules. The SAE J2534-2 document meets these needs by detailing extensions to an SAE J2534-1 specification. It is not required for an interface to be fully compliant with SAE J2534-1 specification to implement some of the features specified in this document. Together, these extensions provide the framework for a common interface to protect the software investment of the Vehicle OEMs and Scan Tool manufacturers. Only the optional features will be described by this document and are based on the December 2004 publication of SAE J2534-1.
This SAE Recommended Practice will define the physical layer and portions of the data link layer of the open systems interconnection model (ISO 7498) for a 500 kbps high-speed CAN (HSC) protocol implementation. Both electronic control unit (ECU) and media design requirements for networks will be specified. Requirements will primarily address the controller area network (CAN) physical layer implementation. Requirements will focus on a minimum standard level of performance from the HSC implementation. All ECUs and media shall be designed to meet certain component level requirements in order to ensure the HSC implementation system level performance at 500 kbps. The minimum performance level shall be specified by system level performance requirements or characteristics described in detail in Section 5 of this document. This document is designed such that if the ECU requirements defined in Section 6 are met, then the system level attributes should be obtainable. This document will address
This Technical Information Report defines the diagnostic communication protocol TP2.0. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECU(s), in which a TP2.0 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an SAE J2534 interface.
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU. It further specifies additional
This SAE Recommended Practice establishes a uniform practice for protecting vehicle components from "unauthorized" access through a vehicle data link connector (DLC). The document defines a security system for motor vehicle and tool manufacturers. It will provide flexibility to tailor systems to the security needs of the vehicle manufacturer. The vehicle modules addressed are those that are capable of having solid state memory contents accessed or altered through the data link connector. Improper memory content alteration could potentially damage the electronics or other vehicle modules; risk the vehicle compliance to government legislated requirements; or risk the vehicle manufacturer's security interests. This document does not imply that other security measures are not required nor possible.
This SAE Recommended Practice establishes a uniform practice for protecting vehicle components from "unauthorized" access through a vehicle data link connector (DLC). The document defines a security system for motor vehicle and tool manufacturers. It will provide flexibility to tailor systems to the security needs of the vehicle manufacturer. The vehicle modules addressed are those that are capable of having solid state memory contents accessed or altered through the data link connector. Improper memory content alteration could potentially damage the electronics or other vehicle modules; risk the vehicle compliance to government legislated requirements; or risk the vehicle manufacturer's security interests. This document does not imply that other security measures are not required nor possible.
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECUs) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. U.S. Environmental Protection Agency (EPA) and the California Air Resources
This SAE Recommended Practice establishes the requirements for a Class B Data Communication Network Interface applicable to all on and off-road land based vehicles. This document defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Although this document addresses all seven layers of the OSI model, it primarily focuses on the Network, Data Link and Physical Layers. Taken in total, the requirements contained in this document specify a data communications network philosophy that satisfies the needs of automotive manufacturers. Although the higher layer OSI requirements are essentially identical for all networks defined by this document (see Section 3.3, Figure 1), differing data rate requirements necessitate the use of different physical layers. Therefore, one physical layer is optimized for a data rate of 10.4 Kbps while the other physical layer is optimized
This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2.8 m high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, and trailer converter dollies. The purpose of the high-mounted stop lamp or lamps is to provide a signal over intervening vehicles to the driver of following vehicles.
This SAE Recommended Practice applies to functions of motor vehicle signalling and marking lighting devices which use light emitting diodes (L.E.D.’s) as light sources. This report provides test methods, requirements, and guidelines applicable to the special characteristics of L.E.D. lighting devices. This Recommended Practice is in addition to those required for devices designed with incandescent light sources. This report is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
This Technical Information Report defines the diagnostic communication protocol Keyword Protocol 1281 (KWP1281). This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECUs, in which a KWP1281 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the KWP1281 protocol in enough detail to support the requirements necessary to implement the communication protocol in an SAE J2534 interface device.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for fog tail lamp systems. See Appendices A and B.
Items per page:
50
1 – 50 of 219488