Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This SAE Surface Vehicle Technical Information Report, SAE J2836/4, establishes diagnostic use cases between plug-in electric vehicles (PEV) and the electric vehicle supply equipment (EVSE). As PEVs are deployed and include both plug-in hybrid electric (PHEV) and battery electric (BEV) vehicle variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document describes the general information required for diagnostics and SAE J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
This document establishes the requirements for screw-on type reattachable couplings for use in low temperature hose assemblies.
This SAE Aerospace Recommended Practice (ARP) identifies and defines a method of measuring those factors affecting installed power available for helicopter powerplants. These factors are installation losses, accessory power extraction, and operational effects. Accurate determination of these factors is vital in the calculation of helicopter performance as described in the RFM. It is intended that the methods presented herein prescribe and define each factor as well as an approach to measuring said factor. Only basic installations of turboshaft engines in helicopters are considered. Although the methods described may apply in principle to other configurations that lead to more complex installation losses, such as an inlet particle separator, inlet barrier filter (with or without a bypass system), or infrared suppressor, specialized or individual techniques may be required in these cases for the determination and definition of engine installation losses. Some rotorcraft may use an
This SAE Aerospace Information Report (AIR) outlines a recommended procedure for evaluation of the vibration environment to which the gas turbine engine powerplant is subjected in the helicopter installation. This analysis of engine vibration is normally demonstrated on a one-time basis upon initial certification, or after a major modification, of an engine/helicopter configuration. This AIR deals with linear vibration as measured on the basic case structure of the engine and not, for example, torsional vibration in drive shafting or vibration of a component within the engine such as a compressor or turbine airfoil. In summary, this AIR discusses the engine manufacturer’s "Installation Test Code" aspects of engine vibration and proposes an appropriate measurement method.
This SAE Aerospace Information Report (AIR) provides an orientation regarding the general technology of chemical oxygen generators to aircraft engineers for assistance in determining whether chemical oxygen generators are an appropriate oxygen supply source for hypoxia protection in a given application and as an aid in specifying such generators. Information regarding the details of design and manufacture of chemical oxygen generators is generally beyond the scope of this document.
This standard covers oronasal type masks which use a continuous flow oxygen supply. Each such mask comprises a facepiece with valves as required, a mask suspension device, a reservoir, or rebreather bag (when used), a length of tubing for connection to the oxygen supply source, and a means for allowing the crew to determine if oxygen is being delivered to the mask. The assembly shall be capable of being stowed suitably to meet the requirements of its intended use.
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
This SAE Recommended Practice establishes mechanical property ranges for low-carbon automotive hot-rolled sheet, cold-rolled sheet, and metallic-coated sheet steels. It also contains information that explains the different nomenclature used with these steels.
This SAE Recommended Practice provides headlamp beam pattern test points for harmonized low and high beam headlamp beam patterns that incorporate elements of European, Asian, and U.S. photometric tables. These photometric tables are optional to those found in SAE J1383.
This specification covers plain rod end bearings, corrosion resistant steel (CRES) or alloy steel, which are self-aligning and self-lubricating by incorporating polytetrafluoroethylene (PTFE) in a liner between the ball and race for use in the temperature range -65 to +325 °F (-54 to +163 °C).
Document provides information on how military/commercial/gas turbine engine test cell/system users may benefit from this unique Coanda/Refraction concept.
This SAE Information Report applies to the control circuits and devices associated with the electrical propulsion system used on electric drive dumpers. Dumper is defined in J/ISO 6165. The document does not apply to auxiliary equipment control systems such as: a Battery charging systems b Engine wiring and control c Monitoring and control circuits not directly affecting the operation of the electric propulsion and retarding system d Lighting e Accessory systems (heating, air conditioning, horns, radios, emergency steering, fire protection, and similar functions).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and mechanical tubing 225 square inches (1452 cm2) and under in cross-sectional area and forging stock of any size.
This SAE Information Report discusses the significant factors which measure the effectiveness of the total occupant restraint system in commonly encountered collision configurations. The total system includes the components which affect occupant injury by influencing the manner in which the collision energy management is accomplished. In addition to the elements that contribute to impact attenuation, consideration must be given to factors that encourage maximum use, such as comfort, reliability, appearance, and convenience. Hence, system evaluation necessarily involves consideration of the complete vehicle.
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the development of aircraft and systems, taking into account aircraft functions and operating environment. It provides practices for ensuring the safety of the overall aircraft design, showing compliance with regulations, and assisting a company in developing and meeting its own internal standards. These practices include validation of requirements and verification of the design implementation for safety, certification, and product assurance. The guidelines in this document were developed in the context of U.S. Title 14 Code of Federal Regulations (14 CFR) Part 25 and European Union Aviation Safety Agency (EASA) Certification Specification (CS) CS-25. They may be applicable in the context of other regulations, such as 14 CFR Parts 23, 27, 29, 33, and 35, and CS-23, CS-27, CS-29, CS-E, and CS-P. This document addresses the development cycle for aircraft and systems that implement aircraft and system functions. It
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling, and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling oxygen cylinders while installed on aircraft, directly or through an intermediate charging port.
This SAE Standard details a uniform method for classifying heat ratings of unshielded spark plugs.
This SAE Standard covers complete general and dimensional specifications for refrigeration tube fittings of the flare type specified in Figures 1 to 42 and Tables 1 to 15. These fittings are intended for general use with flared annealed copper tubing in refrigeration applications. Dimensions of single and double 45 degree flares on tubing to be used in conjunction with these fittings are given in Figure 2 and Table 1 of SAE J533. The following general specifications supplement the dimensional data contained in Tables 1 to 15 with respect to all unspecified details.
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
The intent of this standard is to establish a framework to assure that all evaporators conforming to its requirements demonstrate an acceptable health and safety environment for vehicle occupants as determined from the completed risk assessment. R-744 and low pressure (i.e., non-transcritical refrigerants with a critical temperature between 85 and 120 °C) mobile air conditioning (MAC) refrigerant evaporators shall meet the testing and labeling requirements of this standard. SAE J639 contains a list of all refrigerants considered acceptable for use in mobile thermal systems for which this standard applies when the refrigerant is used in a direct expansion architecture. SAE J639 also requires an assessment to be performed to minimize reasonable risks in MAC systems. The evaporator (as designed and manufactured) shall be part of that risk assessment, and it is the responsibility of the vehicle manufacturer to ensure all relevant aspects of the evaporator are included. It is the
This SAE Standard provides basic information on the International System of Units, abbreviated SI in all languages, and its application in engineering practice and measurement unit usage.
This specification covers a copper alloy (phosphor bronze) in the form of sheet, strip, and plate (see 8.6).
Items per page:
50
1 – 50 of 219833