Results
This SAE Aerospace Recommended Practice (ARP) applies to airline trailer equipment with four wheel running gear pulled and steered through an integral tow bar, for use on airport ramps and other airport areas for transporting baggage, freight, and other materials. This ARP can apply to any airline/airport trailer chassis regardless of its equipment; the trailer bed can be designed to carry either bulk baggage/cargo, or a cargo unit load device by means of a rollerized conveyor system, or a piece of aircraft servicing equipment (e.g., ground power unit, air start unit, etc.).
This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: Tracking transmitter Tracking receiver Telemetry device Remote display This type of tracking equipment is typically used with horizontal earthboring machines as defined in SAE J2022.
This specification covers an aluminum alloy in the form of die forgings from over 2.000 to 10.000 inches (50.8 to 254 mm) in nominal thickness and forging stock of any size (see 8.6).
This specification covers tantalum in the form of sheet, strip, plate, and foil up through 0.1875 inch (4.75 mm), inclusive (see 8.7).
This specification covers a titanium alloy in the form of bars up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2) and forging stock of any size (see 8.7).
This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening intensity and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
An Earned Value Management System (EVMS) integrates the work scope of a program with the schedule and cost elements for optimum program planning and control. The primary purpose of the system is to support integrated program management. The system is owned by the organization and is governed by the organization’s policies and procedures. The principles of an EVMS are: Plan all work scope for the program to completion. Break down the program work scope into finite pieces that are assigned to a responsible person or organization for control of technical, schedule, and cost objectives. Integrate program work scope, schedule, and cost objectives into a performance measurement baseline plan against which accomplishments are measured. Control changes to the baseline. Use actual costs incurred and recorded in accomplishing the work performed. Objectively assess accomplishments at the work performance level. Analyze significant variances from the plan, forecast impacts, and prepare an estimate
This SAE Aerospace Information Report (AIR) covers, and is restricted to, the behavior of air under conditions of critical and subcritical flow at temperatures less than 500 °F.
This SAE Standard provides requirements and guidance to: Develop a Materiel authenticity plan. Procure Materiel from reliable sources. Assure authenticity and conformance of procured Materiel, including methods such as certification, traceability, testing, and inspection appropriate to the Commodity/item in question. Control Materiel identified as counterfeit. Report Suspect or Counterfeit Materiel to other potential users and Authorities Having Jurisdiction.
This SAE Aerospace Standard (AS) provides the essential minimum design, installation, and removal standard for AS4383 adapter reducer and is applicable when specified on engineering drawings, or in procurement documents.
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
This data dictionary provides definitions for quantities, measurement units, reference systems, measurands, measurements, and quantity modalities commonly used in the command and control of cyber-physical systems. A cyber-physical system is an engineered system that is built from, and depends upon, the seamless integration of computational algorithms and physical components. Cyber-physical systems are often interconnected via data links and networks. The term encompasses intelligent vehicles and devices that operate in any environment, including robotic and autonomous systems.
This SAE lab recommended practice may be applied to corrosion test methods such as salt spray, filiform, Corrosion creep back, etc. This procedure is intended to permit corrosion testing to be assessed between Laboratories for correlation purposes.
This SAE Standard specifies a message set, and its data frames and data elements, for use by applications that use vehicle-to-everything (V2X) communications systems.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm), inclusive, in thickness, supplied in the -T361 temper (see 8.5).
This document is a guideline for format, structure and content for ground support equipment (GSE) technical manuals. This document focuses on requirements specific to the GSE industry and does not cover general technical publication practices. Additional standards for GSE and for manufacturer’s publications exist and may add requirements beyond what is covered in this standard. This may include EU Directive 2006/42/EC. This document is written in specific terms by intention, and conforms to recognized practices in the industry. When the word SHALL is used in this standard, it indicates a requirement that must be adhered to in total and does not allow for variance. When the word SHOULD is used, it indicates a recommended practice which allows the manual writer to use discretionary judgment. This document does not apply to electronic test equipment.
This Aerospace Standard (AS) provides the general requirements for hydraulic components that are used in military aircraft and missile hydraulic systems.
This specification covers the engineering requirements for electrodeposition of nickel and the properties of the deposit.
This specification covers the requirements for electrodeposited low-stressed nickel.
The purpose of this test is to evaluate the axial strength of the nut seat of wheels intended for use on passenger cars, light trucks, and multipurpose vehicles. In addition, a minimum contact area is recommended to ensure enough strength for the rotational force in tightening a nut against the nut seat. While this test ensures the minimum strength of the nut seat, the wheel must also have a degree of flexibility. This flexibility, as well as bolt tension, are important to maintain wheel retention.
This specification covers the requirements for an inorganic blackening solution for steel, applied at room temperature.
This SAE Recommended Practice is applicable to all heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine the heat transfer and pressure drop performance of heat exchangers under specified conditions. This document has been reviewed and revised by adding several clarifying statements to Section 4.
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal directional drilling (HDD) machines as defined by ISO 21467:2023.
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 4 inches (102 mm) and under in nominal thickness.
Items per page:
50
1 – 50 of 215784