Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
To establish the acceptance criteria for discontinuities as revealed by magnetic particle or liquid penetrant examination of aircraft utility parts as in 1.2.
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness, or for hexagons least distance between parallel sides in the solution and precipitation heat-treated (H1150) condition.
This specification covers a titanium alloy in the form of prealloyed powder.
This specification covers absorbent fabric materials supplied either as dry cloth or presaturated cloth for solvent cleaning process applications.
This specification covers piston rings fabricated from cast iron.
This SAE Aerospace Standard (AS) provides a standardized test procedure that can be used to evaluate material capability in a dynamic sealing application. This procedure will be utilized by applicable elastomer material specifications which are used for production of O-rings and other seals. This specification is applicable to the dynamic testing requirements for aerospace elastomer parts utilizing materials conforming to AMS7XXX series specifications, user specifications, or print on a Purchase Order (PO) that calls out this document for aerospace applications. This procedure is intended for testing NBR. Other elastomers may have different requirements which will require a separate procedure.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of investment castings.
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy in the form of hand forgings up to 8 inches (203 mm), inclusive, in nominal thickness and a cross-sectional area not over 256 square inches (1652 cm2) and rolled rings up to 3.5 inches (89 mm), inclusive, in nominal thickness and with an OD to wall thickness ratio of 10:1 or greater (see 8.6).
This specification covers an aluminum alloy in the form of wire, sheet, foil, pig, grains, shot, and chips (see 8.6).
This specification covers an aluminum alloy in the form of die forgings from over 2.000 to 10.000 inches (50.8 to 254 mm) in nominal thickness and forging stock of any size (see 8.6).
This specification, in conjunction with the general requirements for steel heat treatment in AMS2759, establishes requirements for thermal stress-relief treatments of parts manufactured from the following materials: a Carbon and low-alloy steels b Tool steels c Precipitation-hardening, corrosion-resistant, and maraging steels d Austenitic corrosion-resistant steels e Martensitic corrosion-resistant steels
This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm), inclusive, in nominal diameter or least distance between parallel sides and 32 square inches (206.46 cm2) maximum cross-sectional area and stock for forging of any size (see 8.7).
This specification covers a premium aircraft-quality alloy steel in the form of welding wire.
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness, or for hexagons least distance between parallel sides in the solution and precipitation heat-treated (H925) condition.
This specification covers a corrosion- and heat-resistant steel in the form of flat wire.
This specification covers an aluminum alloy in the form of centrifugal castings (see 8.6).
This specification covers an aluminum alloy in the form of sheet and plate 0.008 to 1.000 inch (0.203 to 25.4 mm) thick, supplied in the annealed (O) temper (see 8.5). When specified, product shall be supplied in the “as fabricated” (F) temper (see 8.5).
This specification covers an iron-nickel alloy in the form of strip 0.020 to 0.250 inch (0.51 to 6.35 mm), inclusive, in thickness.
This specification covers a corrosion-resistant steel product 12 inches (305 mm) and under in nominal diameter, thickness, or for hexagons, least distance between parallel sides in the solution and precipitation heat treated (H950) condition.
This specification covers a corrosion-resistant steel product 8 inches (203 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 64 in2 (413 cm2) in the solution and precipitation heat treated (H1075) condition
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 4 inches (102 mm) and under in nominal thickness.
Items per page:
50
1 – 50 of 216105