Results
This SAE Aerospace Information Report (AIR) covers the general requirements for, and the listing of, manufacturers’ identification markings, names, symbols or trademarks, and CAGE codes that appear on electrical and electronic wiring devices and accessories as required by individual product specifications. Supplier markings from previous submitted listings are maintained for component traceability.
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test Almen strip holder is required for intensity determination.
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing, or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This document is intended to establish a procedure to certify AD fallback test driver skill levels as an endorsement to SAE J3300 foundational level certification. The SAE J3300/3 endorsement can be used by the individual driver to qualify their skills as a test driver of vehicles with automated driving features. The SAE J3300/3 endorsement levels may also be used by test facilities or other organizations when seeking test or professional drivers with these skills. This document provides directions for obtaining the endorsement, including associated AD fallback test driving skill examination requirements, through SAE J3300-certified Examiners (refer to SAE J3300 for definition). Endorsement registration and associated records are administered through Probitas Authentication®. Probitas Authentication® is the current Independent Program Administrator for the SAE J3300 series. This document is a supplement to SAE J3300, providing information specific to the AD fallback test driver skill
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
The SAE International task force on headlamp mounting height has considered the ramifications of reducing the maximum mounting height of headlamps on highway vehicles. The task force has concluded that it is in the best interest of the driving public to make a substantial reduction in the recommended maximum height at which headlamps, particularly low-beam headlamps, may be mounted. Heights as low as 36 to 40 in (90 to 100 cm) have been considered. New tractor vehicles are in fact being designed with headlamps mounted in this range. Further recommendations were withheld in anticipation of tests to demonstrate the effect of mounting height on the legibility of certain overhead signs.
This SAE Information Report provides information applicable to production Original Equipment Manufacturer antilock braking systems found on some past and current passenger cars and light trucks. It is intended for readers with a technical background. It does not include information about aftermarket devices or future antilock brake systems. Information in this document reflects that which was available to the committee at the time of publication.
See Table 1.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers aluminum alloy die forgings and hand forgings.
This specification covers established inch/pound manufacturing tolerances applicable to carbon steel sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term “excl” is used to apply only to the higher figure of the specified range. Tolerances for product sizes not listed herein shall be as agreed upon by purchaser and vendor.
This specification covers the installation of aircraft interior lighting for military aircraft.
Thrust measurement systems come in many sizes and shapes, with varying degrees of complexity, accuracy and cost . For the purposes of this information report, the discussions of thrust measurement will be limited to axial thrust in single-axis test systems.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This ARP provides definitions and background information regarding the physical performance and testing of DDVs. This ARP also provides extensive guidance for the preparation of procurement specifications and functional testing.
This document describes the requirements of the following test methods for counterfeit detection of electronic components: a Method A: General EVI, Sample Selection, and Handling b Method B: Detailed EVI, including Part Weight measurement c Method C: Testing for Remarking d Method D: Testing for Resurfacing e Method E: Part Dimensions measurement f Method F: Surface Texture Analysis using SEM The scope of this document is focused on leaded electronic components, microcircuits, multi-chip modules (MCMs), and hybrids. Other EEE components may require evaluations not specified in this procedure. Where applicable this document can be used as a guide. Additional inspections or criteria would need to be developed and documented to thoroughly evaluate these additional part types. If AS6171/2 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
This SAE Aerospace Standard (AS) defines Minimum Performance Standards (MPS), qualification requirements, and minimum documentation requirements for side-facing seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant protection under normal operational loads and to define test and evaluation criteria to demonstrate occupant protection when a side-facing seat/occupant/restraint system is subjected to statically applied ultimate loads and to dynamic test conditions set forth in Title 14, Code of Federal Regulations (CFR) Part 23, 25, 27, or 29. While this document addresses system performance, responsibility for the seating system is divided between the seat supplier and the installation applicant. The seat supplier’s responsibility consists of meeting all the seat system performance requirements and obtaining and supplying to the installation applicant all the data prescribed by this document. The
This report investigates the use of single and multi-layer coatings on replaceable headlamp bulbs and how such coatings can affect the performance of bulbs in terms of light scattering, which can contribute to glare, and spectral separation in headlamps. Tests were developed to investigate the effects of absorptive and interference (multi-layer) coatings on bulbs, and on bulbs in headlamp systems. These tests provide validation for a proposed bulb color separation test, which establishes limits for spectral separation within the boundaries of SAE J578 white color requirements. The bulb color separation test provides a definitive selection criterion to identify bulbs that cause excessive light scatter (glare) and/or spectral separation in an optical system.
This specification covers the recommended design, construction, performance and testing requirements for aircraft wheel inflation valves incorporating an inflation pressure gauge which are mounted on the aircraft wheel. These valve/gauge assemblies should be appropriate for use on all aircraft types supported by tubeless tire/wheel assemblies.
This SAE Aerospace Recommended Practice (ARP) sets forth design and operational recommendations concerning the human factors/crew interface considerations and criteria for vertical situation awareness displays. This is the first of two recommended practice documents that will address vertical situation awareness displays (VSAD). This document will focus on the performance/planning types of display (e.g., the map display) and will be limited to providing recommendations concerning human factored crew interfaces and will not address architecture issues. This document focuses on two types of VSAD displays: a coplanar implementation of a profile display (side projection) and a conventional horizontal map display; and a 3D map display (geometric projection). It is intended for head down display applications. However, other formats or presentation methods, such as HUDs, HMDs and 3D audio presentations may become more feasible in the future. Even though the relationship of the vertical
Items per page:
50
1 – 50 of 222189