Results
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This specification covers the installation of aircraft interior lighting for military aircraft.
This SAE Recommended Practice provides general guidelines on the material selection, construction, and qualification of components and wiring systems used to construct nominal 12 VDC and/or 24 VDC electrical wiring systems for heavy-duty vehicles The guidelines are limited to nominal 12 VDC and/or 24 VDC primary wiring systems and includes cable sizes American Wire Gage 20 to AWG 4 on heavy-duty on-highway trucks. The document identifies appropriate operating performances requirements. This document excludes the male-to-female connection of the SAE J560 connectors.
This specification covers the specific requirements for 2024 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing.
This specification covers aluminum foil tape with a pressure sensitive adhesive.
This Handbook is intended to accompany or incorporate AS5643, AS5643/1, AS5657, AS5706, and ARD5708. In addition, full understanding of this Handbook also requires knowledge of IEEE-1394-1995, IEEE-1394a, and IEEE-1394b standards. This Handbook contains detailed explanations and architecture analysis on AS5643, bus timing and scheduling considerations, system redundancy design considerations, suggestions on AS5643-based system configurations, cable selection guidance, and lessons learned on failure modes.
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and forging stock.
This specification covers a copper-nickel-tin alloy in the form of bars and rods.
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
The scope of this document is to define a test method for performing the Compression Stress Relaxation (CSR) Test with the Automotive Standard (ASD) or HP CSR Jig using the appropriate test fixtures, configurations, and procedures. This standard defines the equipment needed, guidelines for running the test, and the format for generating the results and analyzing the data.
This SAE Recommended Practice establishes uniform laboratory techniques for the continuous and bag-sample measurement of various constituents in the exhaust gas of the gasoline engines installed in passenger cars and light-duty trucks. The report concentrates on the measurement of the following components in exhaust gas: hydrocarbons (HC), carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), and nitrogen oxides (NOx). NOx is the sum of nitric oxide (NO) and nitrogen dioxide (NO2). A complete procedure for testing vehicles may be found in SAE J1094. This document includes the following sections: 1. Scope 2. References 3. Emissions Sampling Systems 4. Emissions Analyzers 5. Data Analysis 6. Associated Test Equipment 7. Test Procedures
This specification covers a copper-zinc alloy (brass) in the form of laminated sheet with nominal thickness 0.006 to 0.125 inch (0.15 to 3.18 mm) (see 8.5).
This procurement specification covers aircraft-quality solid rivets made from a corrosion- and heat-resistant cobalt alloy of the type identified under the Unified Numbering System as UNS R30605.
This practice provides a method for evaluating microhardness and microstructure very close (0.002 inch (0.051 mm) or less) to the surface of a disk specimen. Specific accept/reject criteria for partial decarburization (3.7.1), inadvertent carburization/nitriding (3.7.3), total decarburization/intergranular oxidation (3.8), and other characteristics evaluated are to be found in the applicable specification where this ARP is referenced.
This SAE Recommended Practice is intended for use in testing and evaluating the approximate performance of engine-driven cooling fans. This performance would include flow, pressure, and power. This flow and pressure information is used to estimate the engine cooling performance. This power consumption is used to estimate net engine power per SAE J1349. The procedure also provides a general description of equipment necessary to measure the approximate fan performance. The test conditions in the procedure generally will not match those of the installation for which cooling and fuel consumption information is desired. The performance of a given fan depends on the geometric details of the installation, including the shroud and its clearance. These details should be duplicated in the test setup if accurate performance measurement is expected. The performance at a given air density and speed also depends on the volumetric flow rate, or the pressure rise across the fan, since these two
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both beaded hose connections and 37 degree flared connections for use in all types of fluid systems.
This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer
This SAE Aerospace Recommended Practice (ARP) document establishes criteria and recommended practices for the use of airborne icing tankers to aid in design and certification of aircraft ice protection systems and components. Several icing tankers are described, along with their capabilities and suggested use. Sample data for these tanker spray systems are included, shown with 14 CFR Parts 25 and 29, Appendix C icing envelopes for continuous maximum and intermittent maximum icing conditions. (Note: In the remainder of this document, the phrase “Appendix C icing envelopes” will be used for brevity.) This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This specification covers an iron-nickel-cobalt alloy in the form of sheet, strip, and plate.
This SAE Recommended Practice defines a guideline for the fuel injection pump designer to select appropriate fastener designs which are considered to be tamper-resistant. It applies to fuel injection pumps used on diesel engines.
Items per page:
50
1 – 50 of 222094