Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Recommended Practice provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies.
This SAE Recommended Practice provides test protocols with performance requirements for camera monitor systems (CMS) to replace existing statutorily required inside and outside rearview mirrors for U.S. market road vehicles. This practice expands specific technical content while retaining harmonization with the FMVSS 111 rear visibility standard and other international standards. This is accomplished by defining required roadway fields of view as specific fields of view (FOV) displayed inside the vehicle. Specific testing protocols and/or specifications are added to enhance ease of use using straightforward language, and any specifications are intended to be independent of different camera and display technologies unless otherwise explicitly stated.
This specification covers a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
The scope of this SAE Recommended Practice is to promote compatibility between child restraint systems and vehicle seats and seat belts. Design guidelines are provided to vehicle manufacturers for certain characteristics of seats and seat belts and to child restraint system (CRS) manufacturers for corresponding CRS features so that each can be made more compatible with the other. The CRS accommodation fixture (see Figure 1) is used to represent a CRS to the designers of both the vehicle interior and the CRS for evaluation of each product for compatibility with the other. The features of the accommodation fixture are described as each is used.
Three levels of fan structural analysis are included in this practice: a Initial structural integrity. b In-vehicle testing. c Durability (laboratory) test methods. The initial structural integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The in-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The durability test methods section describes the detailed test procedures for a laboratory environment that may be used depending on type of fan, equipment availability, and end objective. The second and third levels build upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
Applies to hydraulic fluid power valves as applied to Off-Road Self-Propelled Work Machines defined in SAE J1116.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice establishes uniform procedures for testing BEVs that are capable of being operated on public and private roads. The procedure applies only to vehicles using batteries as their sole source of power. It is the intent of this document to provide standard tests that will allow for the determination of energy consumption and range for light-duty vehicles (LDVs) based on the federal test procedure (FTP) using the urban dynamometer driving cycle (UDDS) and the highway fuel economy driving schedule (HFEDS) and provide a flexible testing methodology that is capable of accommodating additional test cycles as needed. Additionally, this SAE Recommended Practice provides five-cycle testing guidelines for vehicles performing supplementary testing on the US06, SC03, and cold FTP procedures. Realistic alternatives should be allowed for new technology. Evaluations are based on the total vehicle system’s performance and not on subsystems apart from the vehicle.
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process. This Recommended Practice is applicable during product and process development, product verification and quality control. This Recommended Practice does not replicate or predict actual vehicle performance or part durability.
This document provides a recommended electrical performance testing guideline for LIBM, which makes up an xEV (Battery Electric Vehicles and Hybrid Electric Vehicles) battery pack system. This testing guideline may also be used for other applications, such as stationary, vessel, and aircraft. However, using the guideline for other applications should be determined by the users of this document. Users of this document may also be interested in conducting tests on battery cells and/or battery packs. To avoid conducting potentially redundant tests between cells, modules, and packs, this document does not specify which tests need to be conducted. Determination of which tests need to be conducted is at the user’s discretion and should be based on individual module applications. Rather than specifying which tests need to be conducted, this document describes how each test is to be conducted. This document provides a matrix of tests that can be selectively picked for the application
This Information Report presents background and rationale for SAE Recommended Practice J1106, Laboratory Testing Machine and Procedures for Measuring the Steady Force and Moment Properties of Passenger Car Tires. The purpose of SAE J1106 is to define standards for equipment design and test procedures so that data from different laboratories can be directly compared. Whereas such standardization is not a requirement for testing associated with tire development, it is necessary in the context of vehicle design and tire selection problems. The basic approach employed in developing SAE J1106 was to consolidate and document existing technology as embodied in equipment and procedures currently employed for routine tire evaluations. Equipment and procedures whose current use is restricted to research applications were not considered. Research experience is discussed in this Information Report, however, to the extent deemed necessary to provide background and rationale for SAE J1106. Material
The intent of this document is to develop a recommended practice for PEV chargers, whether onboard or off-board the vehicle, that will enable equipment manufacturers, vehicle manufacturers, electric utilities, and others to make reasonable design decisions regarding power quality. The three main purposes are as follows: 1 To identify those parameters of a PEV battery charger that must be controlled in order to preserve the quality of the AC service. 2 To identify those characteristics of the AC service that may significantly impact the performance of the charger. 3 To identify values for power quality, susceptibility, and power control parameters that are based on current U.S. and international standards. These values should be technically feasible and cost effective to implement into PEV battery chargers. SAE J2894/2 will describe the test methods for the parameters/requirements in this document.
This SAE Recommended Practice establishes the communication for the variety of potential functions for plug-in electric vehicle (PEV) customers. This includes features for use case items in SAE J2836/3 that may be PEV/customer optional equipment, such as AC vehicle-to-load (V2L) and AC vehicle-to-vehicle systems. These systems conform to SAE J1772 with variations required to identify to the PEV bidirectional onboard charger (OBC) the mode of operation changes and output requirements. SAE has published multiple documents relating to PEV and vehicle-to-grid (V2G) interfaces. The various document series are listed below, with a brief explanation of each. Figure 1 shows the sequencing of these documents and their primary function (e.g., the SAE J2836 and SAE J2847/1 documents start with smart charging, SAE J2836 and SAE J2847/2 then add DC charging, etc.). The intent is to have subsequent slash sheets complement each other as more functions and features are included. The /6 series of
This SAE Information Report provides information applicable to production Original Equipment Manufacturer antilock braking systems found on some past and current passenger cars and light trucks. It is intended for readers with a technical background. It does not include information about aftermarket devices or future antilock brake systems. Information in this document reflects that which was available to the committee at the time of publication.
SAE J3108 Recommended Practice (RP) provides fuel and hazard guidance for first and second responders of incidents associated with alternative fueled vehicles. The intent of SAE J3108-1 is to present responders with a limited number of intuitive letters and colors. The International community is in the process of adopting International Standards Organization (ISO) 17840, which provides first and second responders with a standardized format for emergency information. While the ISO 17840 format in coloring and lettering can be adopted and should be encouraged when possible, it is intended for large and heavy vehicles. SAE J3108-1 provides a means for responders to recognize fuel and vehicle type on North American light duty vehicles due to size constraints preventing use of ISO 17840 labels.1 While encouraged to be adopted or referenced by vehicle manufacturers, this RP has been developed for the use of States and other Governmental bodies. The RP is not intended to replace the standards
As the number of Hydraulic Hybrid Powertrain equipped motor vehicles has increased, the number of terms, abbreviations, and acronyms which describe various components of these systems has increased. For the sake of industry standardization and to bring some order to the proliferation of such terms, abbreviations, and acronyms, the SAE Truck and Bus Hydraulic Hybrid committee prepared this document.
This document covers the general physical, electrical, functional, and performance requirements for adapters connected to standards conforming conductive power transfer via handheld conductive coupler capable of transferring either DC or single-phase power using two current-carrying contacts. The focus is on defining the process to evaluate the suitability of adapters for NACS couplers. This edition only covers adapters used between SAE J3400 and SAE J1772.
The marine environment differs greatly from other environments in which hydraulics are used. This Recommended Practice provides hydraulic design considerations and criteria for the marine environment and is applicable to commercial vessels, military ships, and submersible vehicles. This document may be used for manned and un-manned vehicles.
This document covers the dimensional definition of the SAE J3400 (NACS) electric vehicle coupler, which includes the connector and inlet.
This document specifies test procedures to determine the charging performance of electric vehicles. This document facilitates clear and consistent comparisons of realistic charging capabilities of electrically propelled vehicles (EVs) via commercially available electric vehicle supply equipment. It provides details about test conditions, test methods, and test processes derived from typical use cases. Furthermore, it specifies requirements regarding the information for the vehicle operator. This document is applicable to EVs, including plug-in hybrid EVs. This document does not provide requirements for mopeds and motorcycles. Unless specified otherwise, all test procedures can be applied to AC, DC, or wireless charging methods.
Items per page:
50
1 – 50 of 216108