Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This method is intended to define the continuous upper temperature limit (CUTL) of thermoplastic elastomers and thermoset rubber with durometer hardness <=90 Shore A, to oxidation or other degradation when exposed solely to hot air for an extended period of time.
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
This SAE Aerospace Standard (AS) aims at identifying the design criteria and testing methods adequate to guarantee the ultimate load and operational dependability of cargo restraint strap assemblies with a typical 22250 N (5000 lbf) rated ultimate tension load capability, as used by the airline industry in order to restrain cargo on board civil transport aircraft during flight: a cargo loaded and tied down onto airworthiness certified air cargo pallets, themselves restrained into aircraft lower deck or main/upper deck cargo systems and meeting the requirements of NAS 3610 or AS36100, or b non-unitized individual pieces of cargo, or pieces of, cargo placed onto an unrestrained (“floating”) pallet into either lower deck or main deck containerized cargo compartments of an aircraft.
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-road, self-propelled work machines as defined by SAE J1116 (limited to categories of (1) construction, and (2) general purpose industrial).
This SAE Standard provides test procedures, performance requirements and guidelines for auxiliary high beam lamps.
The heating value or heat of combustion is a measure of the energy available from the fuel. The fraction or percentage of the heat of combustion that is converted to useful work is a measure of the thermal efficiency of an engine. Thus, a knowledge of the heat of combustion of the fuel is basic to the engineering of automotive engines. This SAE Information Report provides information on the standardized procedures for determining the heat of combustion of fuels that may be used for automotive engines. The changes to SAE J1498 include: SAE Publications - Added SAE Paper 2010-01-1517 Other Publications and Sections 5, 9, and 10 - Updated ASTM alphanumeric designations and titles. Section 10 - Added discussion of a method to calculate net heating value for gasoline-ethanol blends using ASTM D3338.
This SAE Recommended Practice defines key terms used in the description and analysis of video based driver eye glance behavior, as well as guidance in the analysis of that data. The information provided in this practiced is intended to provide consistency for terms, definitions, and analysis techniques. This practice is to be used in laboratory, driving simulator, and on-road evaluations of how people drive, with particular emphasis on evaluating Driver Vehicle Interfaces (DVIs; e.g., in-vehicle multimedia systems, controls and displays). In terms of how such data are reduced, this version only concerns manual video-based techniques. However, even in its current form, the practice should be useful for describing the performance of automated sensors (eye trackers) and automated reduction (computer vision).
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
This SAE Recommended Practice presents recommendations for test fuels and fluids that can be used to simulate real world fuels. The use of standardized test fluids is required in order to limit the variability found in commercial fuels and fluids. Commercial fuels can vary substantially between manufacturers, batches, seasons, and geographic location. Further, standardized test fluids are universally available and will promote consistent test results for materials testing. Therefore, this document: a Explains commercial automotive fuel components b Defines standardized components of materials test fluids c Defines a nomenclature for test fluids d Describes handling and usage of test fuels e Recommends fluids for testing fuel system materials The test fluid compositions specified in Section 7 of this document are recommended solely for evaluating materials. They are not intended for other activities, such as engine development, design verification, or process validation unless agreed
The purpose of this Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This SAE Recommended Practice establishes the antilock brake system (ABS) sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on or integral to the inboard end of spoke wheels, hubs, rotors, and hub-rotor assemblies on the following axle designations as defined in SAE J1842. a FF b FL c FC d FH e L f R g U h W j N k P
This SAE Recommended Practice identifies and examines the various parameters which must be considered in selecting hydraulic system filters, their locations within the system and the dirt capacity of the filter elements.
This coding system is intended to provide a convenient means of identifying the various tube, pipe, hydraulic hose type, and hose fittings not intended for use in aircraft and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of additional materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. Therefore, it should be the prerogative of the user to apply the code which best satisfies his requirements.
This document describes the major techniques for measuring oil consumption. It does not cover all the sub-variations that might be used to make this measurement.
While this report does not include a discussion of all of the available data defining human response or address all body areas, for those areas addressed it does utilize references generally judged by those in the field to be practical and meaningful guidelines for the development of human surrogates. This report is intended to be a “living” document that will be updated periodically. A number of problems need to be addressed in defining human impact response characteristics. There is the problem of human response variability from subject to subject in volunteer tests. There is the problem of extrapolating such volunteer data which are obtained at low impact severities to higher impact severities using human cadaver response data obtained at injurious levels of impacts. Live animal experiments have been conducted over the years in an attempt to define human impact response and tolerance. The problem with using animal response data is the lack of geometric scaling techniques needed to
This Aerospace Recommended Practice aims at providing general utilization guidelines and calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements performed to restrain cargo on board civil transport aircraft during flight: a Cargo loaded and tied down onto airworthiness approved air cargo pallets, themselves restrained into aircraft lower deck, main deck or upper deck cargo systems meeting the restraint requirements of air cargo pallets approved in accordance with NAS 3610 or AS36100, or b Additional tie-down on aircraft structure when necessitated by pallet maximum gross mass or centre of gravity location, or c Individual pieces of cargo, or pieces of cargo placed onto an unrestrained (“floating”) pallet into either lower deck, main deck or upper deck containerized cargo compartments of an aircraft, or d Individual pieces of load loaded in non-containerized (bulk loaded) baggage or cargo compartments.
This SAE Part Standard covers selected inch dimensioned tapping screws and metallic drive screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a Part Identification Number (PIN) as defined in this standard.
This SAE Aerospace Standard (AS) covers 6-point and 12-point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box end and flare nut wrenches, combination open end and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: (a) non-distorting usage; (b) possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514 and ISO 8434-2; and (c) transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Items per page:
50
1 – 50 of 219717