Results
This SAE Aerospace Information Report (AIR) discusses past and present approaches for monitoring the landing gear structure and shock absorber (servicing), opportunities for corrosion detection, methods for transient overload detection, techniques for measuring the forces seen by the landing gear structure, and methods for determining the fatigue state of the landing gear structure. Landing gear tire condition and tire pressure monitoring are detailed in ARP6225, AIR4830, and ARP6137, respectively. Aircraft Brake Temperature Monitoring Systems (BTMS) are detailed in AS1145.
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This specification covers a two-component compound, an epoxy resin base and a hardener, in the form of a paste.
This analysis applies to crane types as covered by ASME B30.5.
Primarily to provide recommendations concerning minimizing stress-corrosion cracking in wrought titanium alloy products.
This specification established (1) the common requirements for hydraulic units capable of functioning as starters and as pumps suitable for use in aircraft and missiles and (2) the methods to be used for demonstrating compliance with these requirements.
This document applies to the development of Plans for integrating and managing electronic components in equipment for the military and commercial aerospace markets, as well as other ADHP markets that wish to use this document. Examples of electronic components described in this document include resistors, capacitors, diodes, integrated circuits, hybrids, application specific integrated circuits, wound components, and relays. It is critical for the Plan owner to review and understand the design, materials, configuration control, and qualification methods of all “as-received” electronic components and their capabilities with respect to the application; and to identify risks and, where necessary, take additional action to mitigate the risks. The technical requirements are in Section 3 of this standard and the administrative requirements are in Section 4.
The mass of air required to burn a unit mass of fuel with no excess of oxygen or fuel left over is known as the stoichiometric air-fuel ratio. This ratio varies appreciably over the wide range of fuels - gasolines, diesel fuels, and alternative fuels - that might be considered for use in automotive engines. Although performance of engines operating on different fuels may be compared at the same air-fuel ratio or same fuel-air ratio, it is more appropriate to compare operation at the same equivalence ratio, for which a knowledge of stoichiometric air-fuel ratio is a prerequisite. This SAE Recommended Practice summarizes the computation of stoichiometric air-fuel ratios from a knowledge of a composition of air and the elemental composition of the fuel without a need for any information on the molecular weight of the fuel.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
The purpose of this document is to provide guidance for the implementation of DVI for momentary intervention-type LKA systems, as defined by ISO 11270. LKA systems provide driver support for safe lane keeping operations via momentary interventions. LKA systems are SAE Level 0, according to SAE J3016. LKA systems do not automate any part of the dynamic driving task (DDT) on a sustained basis and are not classified as an integral component of a partial or conditional driving automation system per SAE J3016. The design intent (i.e., purpose) of an LKA system is to address crash scenarios resulting from inadvertent lane or road departures. Drivers can override an LKA system intervention at any time. LKA systems do not guarantee prevention of lane drifts or related crashes. Road and driving environment (e.g., lane line delineation, inclement weather, road curvature, road surface, etc.) as well as vehicle factors (e.g., speed, lateral acceleration, equipment condition, etc.) may affect the
The landing gear system is a major and safety critical airframe system that needs to be integrated efficiently to meet the overall aircraft program goals of minimizing the penalties of weight, cost, dispatch reliability and maintenance. As the landing gear system business develops and large-scale teaming arrangements and acquisitions become increasingly common, it may be desirable in some instances to procure an Integrated Landing Gear System. This document provides guidelines and useful references for developing an integrated landing gear system for an aircraft. The document structure is divided into four sections: Landing Gear System Configuration Requirements (Section 3) Landing Gear System Functional Requirements (Section 4) Landing Gear System Integrity Requirements (Section 5) Landing Gear System Program Requirements (Section 6) The landing gear system encompasses all landing gear structural and subsystem elements. Structural elements include shock struts, truck beams, torsion
This procurement specification covers the requirements for metal tube support clamps comprising of two spring clips made of corrosion and heat resistant steel and the associated PTFE single split cushion that supports the tube. See Figure 1.
This specification covers an aluminum alloy in the form of castings (see 8.10).
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
This specification covers the general requirements for the design and construction of air/gas compressor units (see 6.4.1). The detail requirements for a particular air compressor unit shall be as specified in the individual equipment specification for that particular air compressor unit (see 6.2).
This SAE Aerospace Information Report (AIR) contains regulatory and guidance information related to transport airplane hydraulic systems. It contains certain Civil Air Regulations (CAR) and Federal Aviation Regulations (formerly referred to as FARs) from Title 14 Code of Federal Regulations (CFR) in their current version as well as the historical versions. This gives the reader an ability to assemble certain CAR/CFR parts as they existed at any date in the past (referred to as a Regulatory Basis). A certain amount of preamble explanatory material is included, which led to the regulatory rule changes (Amendments to the CFR).
This specification covers an aluminum alloy procured in the form of sheet 0.078 to 0.197 inch (2.00 to 5.00 mm), inclusive, in nominal thickness, Alclad on both sides (see 8.5).
This specification covers an ethylene propylene (EPDM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
Items per page:
50
1 – 50 of 222750