Results
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This document is intended to establish a procedure to certify AD fallback test driver skill levels as an endorsement to SAE J3300 foundational level certification. The SAE J3300/3 endorsement can be used by the individual driver to qualify their skills as a test driver of vehicles with automated driving features. The SAE J3300/3 endorsement levels may also be used by test facilities or other organizations when seeking test or professional drivers with these skills. This document provides directions for obtaining the endorsement, including associated AD fallback test driving skill examination requirements, through SAE J3300-certified Examiners (refer to SAE J3300 for definition). Endorsement registration and associated records are administered through Probitas Authentication®. Probitas Authentication® is the current Independent Program Administrator for the SAE J3300 series. This document is a supplement to SAE J3300, providing information specific to the AD fallback test driver skill
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This SAE Aerospace Information Report (AIR) covers the general requirements for, and the listing of, manufacturers’ identification markings, names, symbols or trademarks, and CAGE codes that appear on electrical and electronic wiring devices and accessories as required by individual product specifications. Supplier markings from previous submitted listings are maintained for component traceability.
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing, or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test Almen strip holder is required for intensity determination.
The test procedure per the applicable Engine Manual does require a vibration check for the low/intermediate and high speed rotor systems. Release of an engine with high vibrations can result in: On-wing vibration complaints, with subsequent troubleshooting Rotor system failures Premature engine removals Limits are provided for transient conditions and steady state data points. Troubleshooting recommendations are limited to verification of the proper signal input and tracking. This practice provides recommendations for: Correct cable and transmitter installation and connections Calibration Recorded data interpretation and data analysis
This specification covers an aluminum alloy in the form of sheet, clad on two sides.
This specification covers the specific requirements for 7178 aluminum alloy, 7011 alclad, plate and sheet; the general requirements are covered in AMS-QQ-A-250. The plate and sheet covered by this specification shall be an integral composite product consisting of a heat-treatable 7178 aluminum alloy core with thin layers of a 7011 aluminum alloy anodic to the core and of approximately equal thickness, bonded to both surfaces.
This SAE Aerospace Information Report (AIR) contains regulatory and guidance information related to transport airplane hydraulic systems. It contains certain Civil Air Regulations (CAR) and Federal Aviation Regulations (formerly referred to as FARs) from Title 14 Code of Federal Regulations (CFR) in their current version as well as the historical versions. This gives the reader an ability to assemble certain CAR/CFR parts as they existed at any date in the past (referred to as a Regulatory Basis). A certain amount of preamble explanatory material is included, which led to the regulatory rule changes (Amendments to the CFR).
This specification covers the procedure for ultrasonic inspection of flat, contoured, round, and hollow cylindrical products having a cross-sectional thickness of 0.02 to 0.50 inch (0.5 to 12.7 mm). This specification does not apply to inspection of composite materials.
This test plan is broken into three major sections for the testing of bus controllers Electrical, Protocol and Noise tests.
This specification establishes engineering requirements for electropolishing metallic parts and materials using Computer Aided Engineering simulation to reduce the process risks related to electropolishing.
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
This SAE Recommended Practice (RP) establishes uniform powered vehicle-level test procedure for forward collision warning (FCW) and automatic emergency braking (AEB) used in trucks and buses greater than 10000 pounds (4535 kg) GVWR equipped with pneumatic brake systems for detecting, warning, and avoiding potential collisions. This RP does not apply to electric powered vehicles, trailers, dollies, etc., and does not intend to exclude any particular system or sensor technology. These FCW/AEB systems utilize various methodologies to identify, track, and communicate data/information to the operator and vehicle systems to warn, intervene, and/or mitigate in the momentary longitudinal control of the vehicle. This specification will test the functionality of the FCW/AEB (e.g., ability to detect objects in front of the vehicle), its ability to indicate FCW/AEB engagement and disengagement, the ability of the FCW/AEB to notify the human machine interface (HMI) or vehicle control system that an
The landing gear system is a major and safety critical airframe system that needs to be integrated efficiently to meet the overall aircraft program goals of minimizing the penalties of weight, cost, dispatch reliability and maintenance. As the landing gear system business develops and large-scale teaming arrangements and acquisitions become increasingly common, it may be desirable in some instances to procure an Integrated Landing Gear System. This document provides guidelines and useful references for developing an integrated landing gear system for an aircraft. The document structure is divided into four sections: Landing Gear System Configuration Requirements (Section 3) Landing Gear System Functional Requirements (Section 4) Landing Gear System Integrity Requirements (Section 5) Landing Gear System Program Requirements (Section 6) The landing gear system encompasses all landing gear structural and subsystem elements. Structural elements include shock struts, truck beams, torsion
This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
This standard lists variables that shall be investigated and reported as an initial investigation into new or revised surface finishes intended for use on fasteners. This standard provides instruction for producing a final report that will be used to determine if further investigation of a surface finish is justified. Further investigation may include tests and evaluations specific to an individual OEM prior to introduction/approval of the surface finish. The final report shall include the results, observations, and conclusions for all of the variables. The final report may be made up of several individual reports covering each variable. In all cases the laboratory performing the test, the test date and the report approver shall be included in the final report.
This AIR is arranged in the following four sections: 2A - Properties of the Natural Environment 2B - Properties of Gases 2C - Properties of Liquids 2D - Properties of Solids A summary of each section is given below.
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
Items per page:
50
1 – 50 of 222501