Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This SAE Aerospace Standard (AS) provides a method for gas turbine engine performance computer programs to be written using Fortran COMMON blocks. If a “function-call application program interface” (API) is to be used, then ARP4868 and ARP5571 are recommended as alternatives to that described in this document. When it is agreed between the program user and supplier that a particular program shall be supplied in Fortran, this document shall be used in conjunction with AS681 for steady-state and transient programs. This document also describes how to take advantage of the Fortran CHARACTER storage to extend the information interface between the calling program and the engine subroutine.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This design standard specifies the dimensions of the externally threaded fitting end to be assembled into an internally threaded fluid system port, using an elastomeric o-ring for sealing. Fitting end dimensions and o-ring sizes agree with ISO 7320-1985.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Aerospace Information Report (AIR) defines helicopter turboshaft engine power assurance theory and methods. Several inflight power assurance example procedures are presented. These procedures vary from a very simple method used on some normal category civil helicopters, to the more complex methods involving trend monitoring and rolling average techniques. The latter method can be used by small operators but is generally better suited to the larger operator with computerized maintenance record capability.
This paper was prepared to support supersession of MIL-S-8879C with Screw Thread Conformity Task Force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. The STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.
This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These are often called “mini coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the mini coax connection system described here is 50 Ω, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable.
This SAE Aerospace Standard (AS) describes taps, thread plug gages, inserting tools, expanding tools, offset and staking tools, tang break-off tools, extracting tools and thread repair kits.
AS81044 covers single conductor electric wires made as specified in the applicable detail specification with tin-coated, silver-coated, or nickel-coated copper or copper alloy conductors insulated with crosslinked polyalkene, crosslinked alkane-imide polymer, or polyarylene. The crosslinked polyalkene, crosslinked alkane-imide polymer, or polyarylene may be used alone or in combination with other insulation materials as specified in the detail specification.
This SAE Standard provides the minimum requirements for high-power, two-conductor jumper cable plug and receptacle for truck-trailer jumper cable systems. It includes the test procedures, design, and performance requirements. This document covers receptacles rated 12 VDC nominal and at more than 30 A (amperes) up to and including 150 A, and is intended for a single circuit with one power conductor and one common return conductor. Single-conductor high-current connectors are not recommended for future designs because of inadequate ground return through fifth wheel/king pin. Cable size selection is to be made by the vehicle OEM for specific applications and the specific voltage drop requirements of those applications. This SAE Standard covers two variants of high-power two-conductor connections: a heavy duty version, with horizontally aligned pins, typically for lift-gate battery charging; and a medium duty version, with vertically aligned pins, typically for loads such as power
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECU’s) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. The U.S. Environmental Protection Agency (EPA) and the California Air
This SAE Recommended Practice applies to three-point hitch (Type A) backhoes as defined in SAE J326 when mounted on either an agricultural tractor as defined in ANSI/ASAE S390 or other off-road self-propelled work machine as defined in SAE J1116. This criterion is intended for the manufacturer of the backhoe, whether or not the backhoe is manufactured or marketed by the same company that manufactures or markets the propelling machine.
This specification defines test methods and requirements for validation of solderless crimped connections. The purpose of this test is to simulate in the lab the stress seen in a typical life (15 years and 150000 miles) for a crimp connection and assure the crimp is mechanically strong and electrically stable. This specification was developed for use with stranded automotive copper wire. Only where specifically mentioned are other constructions or other core materials (aluminum, clad, steel core, etc.) applicable. This specification does not apply to wire types not mentioned, such as coaxial cable crimps, unless a USCAR-21 test is specifically referenced in the test specification for that wire type. This specification is based on accepted levels of environmental exposure for automotive applications. In any intended vehicle application, if the products covered by this specification are or may be subjected to conditions beyond those described in this document, they must pass special
This SAE Aerospace Standard (AS) establishes the characteristics and utilization of 270 V DC electric power at the utilization equipment interface and the constraints of the utilization equipment based on practical experience. These characteristics shall be applicable for both airborne and ground support power systems. This document also defines the related distribution and installation considerations. Utilization equipment designed for a specific application may not deviate from these requirements without the approval of the procuring activity.
This standard defines a generic set of electrical interfaces between a host aircraft (“platform”) and an electro-optic/infrared (EO/IR) sensor. This includes connectors, cabling, fiber optics, signals, and power.
This SAE Aerospace Standard (AS) establishes minimum design and performance requirements for galley insert equipment with an electrical and/or pressure system, as well as associated components intended for installation in galleys and other areas (e.g., bars) of transport category airplanes.
This procurement specification covers aircraft quality metric spanner nuts for retaining shaft mounted parts. Nuts are made from a corrosion and heat resistant age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286, and silver plated. Thread shear proof strength at room temperature is 450 MPa.
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of tire pressure systems, and recommended maintenance practices within the known operating environments. This document is applicable to all axle and all wheel combinations for single unit powered vehicles exceeding 7257 kg (16 000 US lb) gross vehicle weight rating (GVWR), and multi-unit vehicle combinations, up to three (3) towed units, which use an SAE J560 connector for power and/or communication, or equivalent successor connector technology, or which use a suitable capacity wireless solution. Examples of included single chassis vehicles would be – utility and delivery vans, tow trucks, rack trucks, buses, recreational vehicles, fuel trucks, trash trucks, dump trucks, cement trucks, and tractors. Examples of combination vehicles using an SAE J560 or successor connector would be – enclosed van trailers, liquid tanker
This standard is applicable to the marking of aerospace vehicle electrical wires and cables using ultraviolet (UV) lasers. This standard specifies the process requirements for the implementation of UV laser marking of aerospace electrical wire and cable and fiber-optic cable to achieve an acceptable quality mark using equipment designed for UV laser marking of identification codes on aerospace wire and cable. Wiring specified as UV laser markable subject to AS4373 and which has been marked in accordance with this standard will conform to the requirements of AS50881.
This specification is a general level subsystem light source specification that establishes test requirements of light emitting diode (LED) components and modules for use in automotive lighting systems. The completed test data from this test specification is intended to be provided to the OEM by the Tier 1 lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved LED module experiences a design, manufacturing, or component change. This document shall be applied to systems that meet the requirements for design, performance, and validation established by government standards. The LED module is defined as the LED devices and any electronics required to properly energize the LEDs using a vehicle electrical power system along with any associated electrical wiring, connectors, and thermal management system. Samples shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the
Items per page:
50
1 – 50 of 219717