Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This recommended best practice outlines a method for estimating CO2-equivalent emissions using life cycle analysis.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances. This revision (Revision A) is also intended to provide suggested guidelines for synthesizing tire dynamic data necessary for landing gear shimmy analyses.
This specification covers vulcanized sheet made of granulated cork uniformly dispersed in a synthetic rubber compound, for use in gaskets where aromatic fuel or oil resistance is required (See 6.2).
The purpose of this SAE Standard is to establish the specific minimum equipment performance requirements for recovery and recycling of HFC-134a that has been directly removed from, and is intended for reuse in, mobile air-conditioning (A/C) systems. It also is intended to establish requirements for equipment used to recharge HFC-134a to an accuracy level that meets Section 9 of this document and SAE J2099. The requirements apply to the following types of service equipment and their specific applications: Recovery/recycling equipment Recovery/recycling - refrigerant charging Refrigerant recharging equipment only
This SAE Aerospace Standard (AS) establishes minimum design and performance requirements for carts, containers, and associated components intended for installation in galleys and other areas of transport category airplanes. The requirements include establishing installation criteria for use by compartment designers and installers of the equipment.
This section defines the scope of the document, provides a brief history of the Pi-Bus, discusses key features of the Pi-Bus, and provides an overview of the operation of the Pi-Bus. This document is a handbook intended to accompany AS4710 Pi-Bus standard. The purpose of this document is to provide information to aid users of the Pi-Bus, whether they be implementors of Pi-Bus controllers, architects of systems considering using the Pi-Bus, or programmers who must develop applications in a system which uses the Pi-Bus as the backplane communications bus. This document also provides rationale for many of the Pi-Bus requirements as defined in AS4710 and a discussion of potential enhancements that are being considered for the Pi-Bus. The following is a mapping of major sections in this document for particular audiences: a Overview of Pi-Bus and its capabilities: Section 1 b Pi-Bus rationale: Sections 3, 4, and 5 c information for IC designers: Sections 3, 4, 5, 8, and 9 d Information for
This SAE Standard is derived from SAE J2805 and specifies an engineering method for measuring the sound emitted by M and N category road vehicles at standstill and low speed operating conditions.. The specifications reproduce the level of sound which is generated by the principal vehicle sound sources consistent with stationary and low speed vehicle operating conditions relevant for pedestrian safety. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustic environment which is only obtained in an extensive open space or in special designed indoor facilities replicating the conditions of an extensive open space. Such conditions usually exist during: Measurements of vehicles for regulatory certification. Measurements at the manufacturing stage. Measurements at official testing stations. The results obtained by this method give an
This specification establishes engineering requirements for electropolishing metallic parts and materials using Computer Aided Engineering simulation to reduce the process risks related to electropolishing.
The purpose of this SAE Recommended Practice is to provide criteria for determining the acceptability of candidate retrofit refrigerants to replace CFC-12 (R-12) in mobile A/C systems originally designed to use CFC-12 (R-12).
This specification covers a titanium alloy in the form of pre-alloyed powder.
This specification covers a titanium alloy in the form of sheet, strip, and plate on product 0.008 to 3.000 inches (0.20 to 76.20 mm), inclusive, in thickness (see 8.6).
Wire and cable products progress through a series of handling or operational steps from the time they leave the manufacturer, and until a finished harness or assembly is ready for installation on a vehicle. Throughout these many steps, environmental or processing conditions may be present which can generate damage detrimental to the wire or cable and/or its intended application.
This SAE Aerospace Standard (AS) defines the overall requirements applicable to oxygen flow indication as required by Airworthiness Requirements of CS/FAR 25.1449 to show that oxygen is being delivered to the dispensing equipment. Requirements of this document shall be applicable to any type of oxygen system technology and encompass “traditional” pneumatic devices, as well electric/electronic indication.
This specification covers requirements for the material, design, testing and packaging of straight thread tube fitting boss O-rings. O-rings covered by this specification are acrylonitrile-butadiene rubber.
This specification covers insulated wire for use in external aircraft antennas.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6498 cover UNS K23280 with other quality levels.
Items per page:
50
1 – 50 of 222741