Results
This SAE Aerospace Standard (AS) establishes the general requirements for a miniature probe type self-sealing, self-aligning, non-locking coupling intended for aerospace liquid cooling systems. The AS5072/slash sheets define the specific performance and dimensional requirements.
This specification covers one type of copper-beryllium alloy in the form of sheet and strip up to 0.188 inch (4.78 mm) in nominal thickness (see 8.7).
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers a coating consisting of tungsten disulfide without binders and does not require a curing process.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up trucks with dual wheels, and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal to the driver of following (approaching a signaling vehicle from the rear) or oncoming (approaching a signaling vehicle from the front) vehicles over intervening vehicles.
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion-resistant steel product in the solution and precipitation heat-treated (H1025) condition, 4 inches (102 mm) and under in nominal thickness.
This specification covers the requirements for electrodeposited low-stressed nickel.
This specification covers the engineering requirements for electrodeposition of nickel and the properties of the deposit.
This Aerospace Information Report (AIR) has been written to provide in-service reliability data of continuously active ball screw and geared flight control actuation systems.
This SAE Recommended Practice applies to mobile cranes when used in lifting crane service that are equipped with boom length indicating devices.
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This Aerospace Standard (AS) provides the general requirements for hydraulic components that are used in military aircraft and missile hydraulic systems.
This SAE Aerospace Recommended Practice (ARP) establishes software capability guidelines for computer controlled test equipment, hereinafter referred to as automatic test equipment (ATE), for testing hydraulic components. A typical ATE system is shown in Figure 1. The items herein have been selected as potential features which may or may not be applicable to a particular application. This document does not address software development requirements, qualification procedures, or hardware design requirements, but encourages users to refer to existing documents, defined in 2.1.1, for guidance on such issues.
The scope of this SAE Aerospace Information Report (AIR) is to define recommended methods of determining the optimal dimensional relationship of components coupled together using thrust wires for applications such as coupling nuts and fittings. These design parameters are intended to optimize component loading characteristics and maximize wire shear capabilities for both high and low pressure applications.
This Aerospace Recommended Practice (ARP) provides: Recommended methods for cleaning sample bottles, when used, and the solvents to be applied and how these solvents should be prepared. Recommendations for three measuring methods for determining the level of solid particle contamination of hydraulic fluids used in aerospace hydraulics. Recommendations for the selection of the sampling point, sampling method, and the sampling frequency.
This specification covers ground type hydropneumatic pressure accumulators for use in ground support hydraulic systems at rated pressures ranging up to 5,000 psi including details pertinent to the design, fabrication, and performance of the accumulators.
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm), inclusive, in thickness, supplied in the -T361 temper (see 8.5).
This specification covers an aluminum alloy in the form of die forgings from over 2.000 to 10.000 inches (50.8 to 254 mm) in nominal thickness and forging stock of any size (see 8.6).
This specification covers the requirements for an inorganic blackening solution for steel, applied at room temperature.
This specification covers the design and installation requirements for Type I and II military aircraft hydraulic systems.
Items per page:
50
1 – 50 of 215826