Search
Advanced Search
of the following are true
(
)

Results

Items (211,878)
This SAE Recommended Practice covers passive torque biasing axle and center differentials used in passenger car and light truck applications. Differentials are of the bevel gear, helical gear, and planetary types, although other configurations are possible.
Drivetrain Standards Committee
This SAE Recommended Practice covers the design and application of a 120 VAC single phase engine based auxiliary power unit or GENSET. This document is intended to provide design direction for the single phase nominal 120 VAC as it interfaces within the truck 12 VDC battery and electrical architecture providing power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off.
Truck and Bus Electrical Systems Committee
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
A-6C2 Seals Committee
This specification provides dimensional standards for crimp type contact wire barrel design and is a replacement for MS3190. Some wire barrel designs may exist in AS39029 but are not considered approved for future use, therefore, will not appear in this specification. The crimp barrel sizes listed in this document have been standardized in AS39029 and AS22520 specifications, tools and contacts are available to support these listed sizes. These crimp barrel requirements shall be used for any contact, regardless of whether it is a standard or non-standard contact configuration. The specification lists details for three types of wire barrels: A, B, and C. Wire barrel type A is not recommended for new design. Table 4 lists each AS39029 detail sheet wire barrel type.
AE-8C1 Connectors Committee
This standard is primarily intended to apply to new parts and products intended to be produced in an on-going production phase, but can also be applied to parts currently in production (e.g., manufacturing, maintenance). The standard is applicable to all production processes that influence the variation of KCs, as well as maintenance and service processes in which KCs are identified. It applies to organizations for assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product. The variation control process begins with product definition, typically stated in the design documentation (e.g., digital model, engineering drawing, specification) which identifies KCs, and leads to a variation management process for those KCs. This process may also be used for producer-identified KCs (e.g., process KCs, additional/substitute product KCs
G-14 Americas Aerospace Quality Standards Committee (AAQSC)
This SAE Aerospace Information Report (AIR) describes laser wire stripping technologies and recommendations to strip electrical single conductor wires and shielded cables intended for aerospace applications. These recommendations include: Laser types for wire stripping Laser stripping system configuration Quality assurance Tool qualification Tool inspection User health and safety
AE-8D Wire and Cable Committee
This recommended practice covers design requirements for silver, copper and nickel brazed joints, primarily for tube connections, for aerospace propulsion systems. The environmental conditions stated herein, and those given in the applicable AMS specifications, provide the limitations of this ARP.
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the design and test requirements for a spring-loaded, normally-closed hydraulic check valve. The check valve is intended for use in a civil or military aircraft hydraulic system with a rated system pressure up to 5000 psi (34500 kPa).
A-6C5 Components Committee
This Recommended Practice defines the technical requirements for a terrestrial-based PNT system to improve vehicle (e.g., unmanned, aerial, ground, maritime) positioning/navigation solutions and ensure critical infrastructure security, complementing GNSS technologies.
PNT Position, Navigation, and Timing
E-25 General Standards for Aerospace and Propulsion Systems
This standard applies to the aerospace and defense industries and their supply chain.
E-1 Environmental Committee
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
E-25 General Standards for Aerospace and Propulsion Systems
This SAE standard establishes the requirement for suppliers to plan a reliability program that satisfies the following three requirements: a The supplier shall ascertain customer requirements b The supplier shall meet customer requirements c The supplier shall assure that customer requirements have been met
G-41 Reliability
This SAE Aerospace Recommended Practice (ARP) defines additional documentation, environmental considerations, in-service damage limits, test and evaluation criteria necessary to support certification of aircraft seats manufactured using composite materials, in addition to requirements in AS8049 and ARP5526. This document is limited to aircraft seat composite parts in the seat primary load path from the occupant to the attachments of the seat to the aircraft. The term “composite” is inclusive of any fiber-reinforced polymer matrix materials such as carbon fiber-reinforced plastics, sandwich panels and bonded structure.
Aircraft Seat Committee
This SAE Aerospace Standard specifies the dimensional, design criteria, fabrication, performance, operational, environmental, and testing requirements for interline pallets requiring airworthiness approval for loading onto civil transport aircraft equipped with NAS3610/AS36100 restraint systems and using pallet nets meeting the requirements of AS1492. Type II/2 covers NAS3610/AS36100 code sizes. Type III pallets have been removed from this SAE Aerospace Standard revision.
AGE-2 Air Cargo
This procurement specification covers bolts made from a corrosion-resistant, work-strengthened, cobalt-chromium-nickel alloy of the type identified under the Unified Numbering System as UNS R30159.
E-25 General Standards for Aerospace and Propulsion Systems
This SAE Aerospace Recommended Practice (ARP) describes the multi-pass method for evaluating the filtration performance of fine lube filter elements, commonly utilized in aerospace power and propulsion lubrication systems: gas turbine engines, auxiliary power units (APUs), helicopter transmissions, constant speed drives (CSDs), and integrated drive generators (IDGs).
AE-5B Aircraft and Engine Fuel and Lubricant Sys Components
Reducing the power consumption—and hence, the fuel burn—is a major target for the next generation of aircraft, and electrical actuation is perceived as a technological area able to provide power saving. Electrical actuation can in fact contribute to the reduction of the non-propulsive power because electro-mechanical actuators, when compared to the conventional hydraulic actuators, rely on a form of power subjected to lower distribution losses and in general can lead to a weight savings at the aircraft level if the required power remains under a break-over point. Moreover, electro-mechanical actuators (EMAs) present higher reliability and maintainability with a lower life-cycle cost. Two critical issues with electrically powered actuation are the temperature rise in the electric motor windings and in the power electronics, and the sensitivity to certain single point of failures that can lead to mechanical seizures, that has so far thwarted the use of EMAs for safety-critical
HM-1 Integrated Vehicle Health Management Committee
This specification covers all aspects in Electrical Wiring Interconnection Systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles, and external pods.
AE-8A Elec Wiring and Fiber Optic Interconnect Sys Install
Items per page:
1 – 50 of 211878