Search
Advanced Search
of the following are true

Results

Items (206,872)
This SAE Recommended Practice provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability, and environmental performance when tested according to SAE J2902
Truck and Bus Brake Actuator Committee
This document establishes the minimum training and qualification requirements for ground-based aircraft deicing/anti-icing methods and procedures. All guidelines referred to herein are applicable only in conjunction with the applicable documents. Due to aerodynamic and other concerns, the application of deicing/anti-icing fluids shall be carried out in compliance with engine and aircraft manufacturers’ recommendations. The scope of training should be adjusted according to local demands. There are a wide variety of winter seasons and differences of the involvement between deicing operators, and therefore the level and length of training should be adjusted accordingly. However, the minimum level of training shall be covered in all cases. As a rule of thumb, the amount of time spent in practical training should equal or exceed the amount of time spent in classroom training
G-12T Training and Quality Programs Committee
This specification establishes the requirements for a hard anodic coating on aluminum and aluminum alloys
AMS B Finishes Processes and Fluids Committee
This SAE Systems Management Standard specifies the Habitability processes throughout planning, design, development, test, production, use and disposal of a system. Depending on contract phase and/or complexity of the program, tailoring of this standard may be applied. Appendix C provides guidance on tailoring standard requirements to fit the various DoD acquisition pathways. The primary goals of a contractor Habitability program include: Ensuring that the system design complies with the customer Habitability requirements and that discrepancies are reported to management and the customer. Identifying, coordinating, tracking, prioritizing, and resolving Habitability risks and issues and ensuring that they are: ◦ Reflected in the contractor proposal, budgets, and plans. ◦ Raised at design, management, and program reviews. ◦ Debated in working group meetings. ◦ Coordinated with Training, logistics, and the other HSI disciplines. ◦ Included appropriately in documentation and deliverable
G-45 Human Systems Integration
The devices of this SAE Standard provide the means by which passenger compartment dimensions can be obtained using a deflected seat rather than a free seat contour as a reference for defining seating space. All definitions and dimensions used in conjunction with this document are described in SAE J1100. These devices are intended only to apply to the driver side or center occupant seating spaces and are not to be construed as instruments which measure or indicate occupant capabilities or comfort. This document covers only one H-point machine installed on a seat during each test. Certified H-point templates and machines can be purchased from: SAE International 400 Commonwealth Drive Warrendale, PA 15096-0001 Specific procedures are included in Appendix A for seat measurements in short- and long-coupled vehicles and in Appendix B for measurement of the driver seat cushion angle. Specifications and a calibration inspection procedure for the H-point machine are given in Appendix C
Human Accom and Design Devices Stds Comm
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This SAE recommended practice provides procedures and methods for testing service, spring applied parking and combination brake actuators for air disc brake applications. Methods and recommended samples for testing durability, function and environmental performance are listed in 1.1 and 1.2
Truck and Bus Brake Actuator Committee
This SAE Recommended Practice outlines a procedure for selecting the proper specification for carbon steel sheet and strip which are purchased to make an identified part. Specifications considered are: ASTM A109—Steel, Carbon, Cold Rolled Strip. ASTM A569—Steel, Carbon (0.15 maximum percent), Hot Rolled Sheet, Commercial Quality (HRCQ). ASTM A621—Steel, Sheet, Carbon, Hot Rolled, Drawing Quality (HRDQ). ASTM A622—Steel, Sheet, Carbon, Hot Rolled, Drawing Quality, Special Killed (HRDQSK). ASTM A568—Steel, Carbon and High-Strength Low-Alloy Hot Rolled Sheet, and Cold Rolled Sheet, General Requirements. ASTM A366—Steel, Carbon, Cold Rolled Sheet, Commercial Quality (CRCQ). ASTM A619—Steel, Sheet, Carbon, Cold Rolled, Drawing Quality (CRDQ). ASTM A620—Steel, Sheet, Carbon, Cold Rolled, Drawing Quality, Special Killed (CRDQSK). ASTM A749M—Steel, Carbon and High-Strength Low-Alloy, Hot Rolled Strip, General Requirements. ASTM A635—Steel Sheet and Strip, Carbon, Hot Rolled Commercial Quality
Metals Technical Committee
The purpose of this SAE Aerospace Information Report (AIR) is to provide guidance for aircraft engine and propeller systems (hereafter referred to as propulsion systems) certification for cybersecurity. Compliance for cybersecurity requires that the engine control, propeller control, monitoring system, and all auxiliary equipment systems and networks associated with the propulsion system (such as nacelle systems, overspeed governors, and thrust reversers) be protected from intentional unauthorized electronic interactions (IUEI) that may result in an adverse effect on the safety of the propulsion system or the airplane. This involves identification of security risks, their mitigation, verification of protections, and their maintenance in service. This document is intended to serve as suitable guidance for propulsion system manufacturers and applicants for propulsion system type certification. It is also intended to provide guidance for subsequent propulsion system integration into
E-36 Electronic Engine Controls Committee
This document provides general and specific design guidance for the development of software data loading equipment for all types of aircraft. The primary purpose of data load is to upload loadable software parts to airborne computers. A secondary function of data load is downloading data from airborne computers. Software data load functionality generally falls into the following categories: Portable Data Loader (PDL) for loading equipment on the ground or carried onto aircraft to perform onboard loading. Airborne Data Loader (ADL) for installation on aircraft to perform onboard loading. Data Load Function (DLF) is software that performs the data loading. This document defines data loaders designed to load avionics equipment over a high-speed interface using an Ethernet network protocol. This document defines media interfaces and protocol requirements specific to all data load functions, whether portable or airborne. This document also describes the desired capabilities of data loading
Airlines Electronic Engineering CommitteeAvionics Maintenance CommitteeFlight Simulator Engineering and Maintenance Committee
This document is intended to supplement the SAE J1939 documents by offering the SAE J1939 information in a form that can be sorted and search for easier use
Truck Bus Control and Communications Network Committee
This document covers the general physical, electrical, functional, testing, and performance requirements for conductive power transfer, primarily for vehicles using a conductive ACD connection capable of transferring DC power. It defines conductive power transfer methods, including the infrastructure electrical contact interface, the vehicle connection interface, the electrical characteristics of the DC supply, and the communication system. It also covers the functional and dimensional requirements for the vehicle connection interface and supply equipment interface. New editions of the documents shall be backwards compatible with the older editions. There are also sub-documents which are identified by a SAE J3105/1, SAE J3105/2, and SAE J3105/3. These will be specific requirements for a specific interface defined in the sub-document. SAE J3105: Main document, including most requirements. ○ SAE J3105/1: Infrastructure-Mounted Cross Rail Connection ○ SAE J3105/2: Vehicle-Mounted
Hybrid - EV Committee
This SAE Aerospace Standard (AS) defines the nomenclature for surface finishes commonly used for sheet and strip in aerospace material specifications. It is applicable to steel and to iron, nickel, cobalt, and titanium base alloys
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Recommended Practice defines and establishes mechanical property ranges for seven grades of continuously cast high strength automotive sheet steels that can be formed, welded, assembled, and painted in automotive manufacturing processes. The grade of steel specified for an identified part should be based on part requirements (configuration and strength) as well as formability. Material selection should also take into consideration the amount of strain induced by forming and the impact strain has on the strength achieved in the finished part. These steels can be specified as hot-rolled sheet, cold-reduced sheet, uncoated, or coated by hot dipping, electroplating, or vapor deposition of zinc, aluminum, and organic compounds normally applied by coil coating. The grades and strength levels are achieved through chemical composition and special processing. Not all combinations of strength and coating types may be commercially available. Consult your steel supplier for details
Metals Technical Committee
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
xEVs involved in incidents present unique hazards associated with the high voltage system (including the battery system). These hazards can be grouped into three categories: chemical, electrical, and thermal. The potential consequences can vary depending on the size, configuration, and specific battery chemistry. Other incidents may arise from secondary events such as garage fires and floods. These types of incidents are also considered in the recommended practice (RP). This RP aims to describe the potential consequences associated with hazards from xEVs and suggest common procedures to help protect emergency responders, tow and/or recovery, storage, repair, and salvage personnel after an incident has occurred with an electrified vehicle. Industry design standards and tools were studied and where appropriate, suggested for responsible organizations to implement. Lithium ion (Li-ion) batteries used for vehicle propulsion power are the assumed battery system of this RP. This chemistry is
Hybrid - EV Committee
This SAE Standard specifies a method for testing and measuring elastic constants in friction materials by precise ultrasonic velocity measurements. Measurement methods are also described for measurement of the out-of-plane modulus as a function of pre-load as well as the measurement of engineering constants as a function of temperature. Finally, methods are formulated to produce all engineering constants as a function of pre-load and temperature
Brake Linings Standards Committee
This standard is issued in loose leaf form to permit the insertion or removal of new or revised sections and test methods. All users of this standard should keep it up-to-date by inserting the revised or new sections and test methods as issued and by removing the superseded pages. New and revised sections will be issued with a revised title page showing the latest revision date and with a revised index Section 3). In Section 3, the most closely corresponding FED, TEST METHOD STD NO. 228 Method number and the most closely corresponding ASTM Test Procedure is given for reference purposes. No implication of agreement with those test methods or procedures is intended. This standard gives the general physical, electrical, and chemical methods for testing wires and cables for conformance to the requirements of their controlling detail specifications and other related documents. This standard also includes methods (Group 5000) for comparative evaluation testing of wires and cables. It was
AE-8D Wire and Cable Committee
This SAE Aerospace Recommended Practice (ARP) provides minimum standards and environmental design requirement recommendations for lighting and control in galley areas. It also addresses electrical shock hazard in galley areas. The use of “shall” in this document expresses provisions that are binding. Non-mandatory provisions use the term “should
A-20C Interior Lighting
This specification covers a thermally-stabilized, irradiated, modified fluoropolymer in the form of very-thin-wall tubing
AE-8D Wire and Cable Committee
This specification covers both insulated and uninsulated solid conductor wire, designed for solderless wrap connections in electrical and electronic devices and equipment. The terminations of the wire are intended to be made with hand or automatic tools which wrap the wire, under tension, around terminal pins (commonly called wrapposts) to form solderless wrapped connections
AE-8D Wire and Cable Committee
This document outlines the development process and makes recommendations for total antiskid/aircraft systems compatibility. These recommendations encompass all aircraft systems that may affect antiskid brake control and performance. It focuses on recommended practices specific to antiskid and its integration with the aircraft, as opposed to more generic practices recommended for all aircraft systems and components. It defers to the documents listed in Section 2 for generic aerospace best practices and requirements. The documents listed below are the major drivers in antiskid/aircraft integration: 1 ARP4754 2 ARP4761 3 RTCA DO-178 4 RTCA DO-254 5 RTCA DO-160 6 ARP490 7 ARP1383 8 ARP1598 In addition, it covers design and operational goals, general theory, and functions, which should be considered by the aircraft brake system engineer to attain the most effective skid control performance, as well as methods of determining and evaluating antiskid system performance. For definitions of
A-5A Wheels, Brakes and Skid Controls Committee
This SAE Aerospace Recommended Practice (ARP) is only applicable to 14 CFR Part 25 transport airplane passenger and flight attendant seats. This document provides an approach for determining which parts on aircraft seats are required to meet the test requirements of 14 CFR Part 25 Appendix F, Parts IV and V. Additionally, it is recommended to use materials that meets the requirements of 14 CFR Part 25 Appendix F, Parts IV and V in applications where not required. Independent furniture installations related to seat installations are outside the scope of this document
Aircraft Seat Committee
This SAE Aerospace Recommended Practice (ARP) defines additional documentation, environmental considerations, in-service damage limits, test and evaluation criteria necessary to support certification of aircraft seats manufactured using composite materials, in addition to requirements in AS8049 and ARP5526. This document is limited to aircraft seat composite parts in the seat primary load path from the occupant to the attachments of the seat to the aircraft. The term “composite” is inclusive of any fiber-reinforced polymer matrix materials such as carbon fiber-reinforced plastics, sandwich panels and bonded structure
Aircraft Seat Committee
This SAE Aerospace Recommended Practice (ARP) defines a means of assessing the credibility of computer models of aircraft seating systems used to simulate dynamic impact conditions set forth in Title 14, Code of Federal Regulations (14 CFR) Parts 23.562, 25.562, 27.562, and 29.562. The ARP is applicable to lumped mass and detailed finite element seat models. This includes specifications and performance criteria for aviation specific virtual anthropomorphic test devices (v-ATDs). This document provides a recommended methodology to evaluate the degree of correlation between a seat model and dynamic impact tests. This ARP also provides best practices for testing and modeling designed to support the implementation of analytical models of aircraft seat systems. Supporting information within this document includes procedures for the quantitative comparison of test and simulation results, as well as test summaries for data generated to support the development of v-ATDs and a sample v-ATD
Aircraft Seat Committee
This document covers the recommended practice for determining the acceptability of the dendrite arm spacing (DAS) of D357-T6 aluminum alloy castings required to have tensile strength not lower than 50 ksi (345 MPa
AMS D Nonferrous Alloys Committee
This specification covers a precipitation hardenable, corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD and 0.015 inch (0.38 mm) and over in nominal wall thickness
AMS F Corrosion and Heat Resistant Alloys Committee
This document covers all metal, self-locking wrenching nuts, plate nuts, shank nuts, and gang channel nuts made from a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286 and of 160 ksi tensile strength at room temperature, with maximum test temperature of parts at 1200 °F
E-25 General Standards for Aerospace and Propulsion Systems
Items per page:
1 – 50 of 206872