Results
This SAE Recommended Practice establishes a procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers that may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853, SAE J187, SAE J272, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that review and coordination of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery
The AS6224 specification covers environment resistant, permanent insulation repair sleeves for repairing different types of insulation damages of wire or cable jackets in installed applications. The repair sleeve is intended to repair damaged primary wire or cable jacket covers where the shielding and wire conductors are not damaged
This SAE Standard applies to off-road self-propelled work machines as categorized in SAE J1116. Fast fill fueling typically applies to self-propelled machines with a fuel capacity over 380 L, although fast fill fueling can be used on machines with smaller fuel capacity
This document includes requirements of installations of adequate landing and taxiing lighting systems in aircraft of the following categories: a Single engine personal and/or liaison type b Light twin engine c Large multiengine propeller d Large multiengine turbojet/turbofan e Military high-performance fighter and attack f Helicopter This document will cover general requirements and recommended practices for all types of landing and taxi lights. More specific recommendations for LED lights in particular can be found in ARP6402
This SAE Aerospace Recommended Practice (ARP) provides recommended practices for the calibration and acceptance of icing wind tunnels to be used in testing of aircraft components and systems and for the development of simulated ice shapes. This document is not directly applicable to air-breathing propulsion test facilities configured for the purposes of engine icing tests, which are covered in AIR6189. This document also does not provide recommended practices for creating Supercooled Large Drop (SLD) or ice crystal conditions, since information on these conditions is not sufficiently mature for a recommended practice document at the time of publication of ARP5905A. Use of facilities as part of an aircraft’s ice protection Certification Plan should be reviewed and accepted by the applicable regulatory agency prior to testing. Following acceptance of a test plan, data generated in these facilities may be submitted to regulatory agencies for use in the certification of aircraft ice
This SAE Standard establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children’s snowmobile as identified in 1.2
This SAE Standard was prepared by Technical Committee 1, Engine Lubrication, of SAE Fuels and Lubricants Council. The intent is to improve communications among engine manufacturers, engine users, and lubricant marketers in describing lubricant performance characteristics. The key objective is to ensure that a correct lubricant is used in each two-stroke-cycle engine
This SAE Standard provides test procedures, requirements, and guidelines for a parking lamp
Instructions on this chart are intended to be used as a ready reference by personnel responsible for servicing off-road self-propelled work machines described in SAE J1116, categories 1, 2, 3, and 4. Detailed maintenance and service guidelines are reserved for maintenance, operator, and lubrication manuals as defined in SAE J920
This SAE Recommended Practice applies to off-road, self-propelled work machine categories of earthmoving, forestry, road building and maintenance, and specialized mining machinery as defined in SAE J1116
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors. The equipment specified here will identify smaller refrigerant leaks when servicing motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning the equipment design or use beyond that of sampling a flammable refrigerant, save those described in 3.1 and 3.2 of this document. All requirements of this standard shall be verified in SAE J2911
This SAE Recommended Practice describes the basic content requirements, barcode specifications, and functional test specifications of the vehicle identification number (VIN) label. On the vehicle, the VIN label is to be mounted in a readily accessible location for use of a barcode scanning device
The information in this SAE Recommended Practice has been compiled by Technical Committee 1 (Engine Lubrication) of the SAE Fuels and Lubricants Division. The intent is to provide those concerned with the design and maintenance of two-stroke-cycle engines with a better understanding of the properties of two-stroke-cycle lubricants. Reference is also made to test procedures which may be used to measure the chemical and physical characteristics of these lubricants
This specification covers the requirements for self-sealing, quick-disconnect couplings for fuel and oil system components
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock
This SAE Aerospace Standard (AS) is intended for use by those involved in the design of aircraft, missile, or space systems, and their support equipment to define the various types of fastener torque
This SAE Recommended Practice provides the test procedure and instructions for air braked single unit trucks, buses, and combination vehicles. Brake force distribution testing with systems post-reduced stopping distance changes is still appropriate; however, vehicles with electrononically controlled braking systems are not covered in this document and may need to be addressed in the future. It also provides recommendations for: a Instrumentation and equipment. b Vehicle preparation. c Calculating distribution of brake force
This SAE Recommended Practice identifies and defines terms specifically related to truck and bus braking systems including Antilock Brake Systems (ABS) and Electronically Controlled Braking Systems (ECBS
This Recommended Practice covers air braked trucks, truck-tractors, trailers and buses. It enumerates the identification and installation of the air brake components not covered in other SAE recommended practices and standards
This SAE Recommended Practice is intended for measuring the static brake torque performance of a pnuematically actuated brake assembly, friction material, and drum/disc combination on an inertia brake dynamometer
This SAE Recommended Practice provides a field test procedure and instructions for air braked single unit trucks, buses, and combination vehicles. Brake force distribution field testing with systems post-reduce stopping distance changes is still appropriate, however, vehicles with electronically controlled braking systems are not covered in this document and may need to be addressed in the future. It also provides recommendations for: a Instrumentation and equipment. b Vehicle preparation. c Test of air-braked single and combination vehicles. d Calculation of brake force distribution. e This test procedure is intended to be used as a field procedure. If a more refined method, utilizing laboratory equipment, is required, refer to SAE J1505
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) air and is not directly applicable to vehicles with other systems. Air over hydraulic systems are to be tested as air systems
This specification establishes the requirements for flake or granular cetyl alcohol, solvents for dissolving the cetyl alcohol, preparation and application requirements for use of cetyl alcohol as an installation lubricant on mechanical fasteners, such as pins, bolts, nuts, washers, threaded or nonthreaded fastening devices, and inspection criteria for coated parts
This standard covers the requirements for non-separable, airframe antifriction needle bearings and corrosion-resistant and traditional materials intended for use in flight vehicle control systems with radial loads
This specification covers a carbon steel in the form of sheet and strip
This SAE Standard provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system
The purpose of this document is to define design, construction, operational, and maintenance requirements for hydrogen fuel storage and handling systems in on-road vehicles. Performance-based requirements for verification of design prototype and production hydrogen storage and handling systems are also defined in this document. Complementary test protocols (for use in type approval or self-certification) to qualify designs (and/or production) as meeting the specified performance requirements are described. Crashworthiness of hydrogen storage and handling systems is beyond the scope of this document. SAE J2578 includes requirements relating to crashworthiness and vehicle integration for fuel cell vehicles. It defines recommended practices related to the integration of hydrogen storage and handling systems, fuel cell system, and electrical systems into the overall Fuel Cell Vehicle
The goal of the Pedestrian Test Mannequin Task Force is to develop standard specifications/requirements for pedestrian test mannequins (1 adult and 1 child) that are representative of real pedestrians to the sensors used in Pedestrian Detection systems and can be used for performance assessment of such in-vehicle systems (including warning and/or braking) in real world test scenarios/conditions. This version of the document only includes the pedestrian mannequin for vision, Lidar, and/or 76 to 78 GHz radar based Pedestrian Pre-collision systems
While there are various types of Fuel Cell architectures being developed, the focus of this document is on Proton Exchange Membrane (PEM) fuel cell stacks and ancillary components for automotive propulsion applications. Within the boundaries of this document are the: Fuel Supply and Storage, Fuel Processor, Fuel Cell Stack, and Balance of Plant, as shown in Figure 1
This document provides background information, rationale, and data (both physical testing and computer simulations) used in defining the component test methods and similarity criteria described in SAE Aerospace Recommended Practice (ARP) 6330. ARP6330 defines multiple test methods used to assess the effect of seat back mounted IFE monitor changes on blunt trauma to the head and post-impact sharp edge generation. The data generated is based on seat and IFE components installed on type A-T (transport airplane) certified aircraft. While not within the scope of ARP6330, generated test data for the possible future development of surrogate target evaluation methods is also included
This specification covers the requirements for electrodeposited chromium plating
Items per page:
50
1 – 50 of 212615