Search
Advanced Search
of the following are true
(
)

Results

Items (211,798)
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness (see 8.4
AMS F Corrosion and Heat Resistant Alloys Committee
The devices of this SAE Standard provide the means by which passenger compartment dimensions can be obtained using a deflected seat rather than a free seat contour as a reference for defining seating space. All definitions and dimensions used in conjunction with this document are described in SAE J1100. These devices are intended only to apply to the driver side or center occupant seating spaces and are not to be construed as instruments which measure or indicate occupant capabilities or comfort. This document covers only one H-point machine installed on a seat during each test. Certified H-point templates and machines can be purchased from: SAE International 400 Commonwealth Drive Warrendale, PA 15096-0001 Specific procedures are included in Appendix A for seat measurements in short- and long-coupled vehicles and in Appendix B for measurement of the driver seat cushion angle. Specifications and a calibration inspection procedure for the H-point machine are given in Appendix C
Human Accom and Design Devices Stds Comm
This SAE Recommended Practice applies to the use, by automotive service technicians, of generally available leak detection methods to service motor vehicle passenger compartment air conditioning systems
Interior Climate Control Service Committee
This SAE standard applies to self-propelled driver operated sweepers and scrubbers as defined in SAE J2130-1
MTC2, Sweeper, Cleaner, and Machinery
This specification covers an aluminum alloy in the form of sheet and plate 0.020 to 0.499 inch (0.51 to 12.67 mm), inclusive, in nominal thickness alclad two sides (see 8.5
AMS D Nonferrous Alloys Committee
This SAE Recommended Practice describes the test procedures for conducting quasi-static cab roof strength tests for heavy-truck applications. Its purpose is to establish recommended test procedures which will standardize the procedure for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included
Truck Crashworthiness Committee
This SAE Recommended Practice applies to three-point hitch (Type A) backhoes as defined in SAE J326 when mounted on either an agricultural tractor as defined in ANSI/ASAE S390 or other off-road self-propelled work machine as defined in SAE J1116. This criterion is intended for the manufacturer of the backhoe, whether or not the backhoe is manufactured or marketed by the same company that manufactures or markets the propelling machine
OPTC1, Personnel Protection (General)
This SAE standard provides manufacturers/marketers, testing facilities, and providers of technician training with a procedure for certifying compliance with the applicable standard. Manufacturers/marketers or sellers who advertise their products as certified to an SAE J standard shall follow this procedure. Certification of a product is voluntary; however, this certification process is mandatory for those advertising meeting SAE standard(s) requirements. Only certifying to this standard allows those claiming compliance to advertise that their product (unit), component, or service technician training meets all requirements of the applicable SAE standard. Certification of compliance to this and the appropriate standard and use of the SAE label on the product shall only be permitted after all the required information has been submitted to SAE International and it has been posted on the SAE website. This process is mandatory for those advertising as being “Certified to SAE JXXXX-(version
Interior Climate Control Steering Committee
This SAE Recommended Practice establishes testing methods and performance requirements for windshield wiping systems on trucks, buses, and multipurpose passenger vehicles with a GVWR of 4500 kg (10000 pounds) or greater and light duty utility vehicles with a GVWR of less than 4500 kg (10000 pounds). The test procedures and minimum performance requirements, outlined in this document, are based on currently available engineering data. It is the intent that all portions of the document will be periodically reviewed and revised as additional data regarding windshield wiping system performance are developed
Truck and Bus Windshield Wipers and Climate Control Comm
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, and flash-welded rings up to 4.00 inches (101.6 mm), exclusive, in least distance between parallel sides (thickness) or diameter, and stock of any size for forging or flash-welded rings
AMS F Corrosion and Heat Resistant Alloys Committee
This SAE Recommended Practice applies to technical publications which present instructions for the proper unloading, set-up, installations, pre-delivery inspection, operation, and servicing of off-road self-propelled work machines as categorized in SAE J1116. Advertising/marketing and other pre-purchase publications are not included
Machine Technical Steering Committee
This specification establishes process controls for the repeatable implementation of the CSAM process for the manufacturing of metallic and metal-nonmetal blend components
AMS AM Additive Manufacturing Metals
The lubricant performance capability for aero-propulsion drive systems is derived from the physical properties, chemical properties, and the transport phenomena of the oil. Viscosity, pressure-viscosity coefficient, and elastohydrodynamic (EHD) full-film traction coefficient are inherent properties of the lubricating fluid. Full-film traction coefficient is a required input for thermal performance prediction and engineering design. Traction coefficient data can be modeled and used as an input into bearing and gear analysis codes. This document describes a test method for traction coefficient measurement of 5 cSt oils under service-like conditions for high-stress Hertzian elastic contacting bodies operating under temperatures and sliding (slip) velocities found in high-speed rolling element bearings and gears
E-34 Propulsion Lubricants Committee
Items per page:
1 – 50 of 211798