Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This specification and part standard specifies polytetrafluoroethylene (PTFE) resin material and the dimensional requirements for scarf-cut retainers (backup rings) previously specified by MIL-R-8791 and MIL-R-8791/1. The retainers are intended for use in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with seals and O-rings.
This Standard applies to integrated circuits and semiconductors exhibiting the following attributes: a A minimum set of requirements, or information provided by the part manufacturer, which will allow a standard COTS component to be designated AQEC by the manufacturer. b As a minimum, each COTS component (designated AQEC) will have been designed, fabricated, assembled, and tested in accordance with the component manufacturer’s requirements for standard data book components. c Qualification of, and quality systems for, the COTS components to be designated as AQEC shall include the manufacturer’s standards, operating procedures, and technical specifications. d Components manufactured before the manufacturer has addressed AQEC requirements, but utilizing the same processes, are also considered AQEC compliant. e Additional desired attributes of a device designated AQEC (that will support AQEC users) are found in Appendix B of this standard. NOTE: Parts qualified to military specifications
This specification establishes the requirements for various types of identification sleeving that will shrink to a predetermined size upon the application of heat after it has been marked. Continuous operating temperature ratings range from -55° to 175°C (-67° to 347°F). (See 6.1).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Scope is unavailable.
The intent of this document is to define the methodology for suspect parts inspection using radiological inspection. The purpose of radiology for suspect counterfeit part inspection is to detect deliberate misrepresentation of a part, either at the part distributor or original equipment manufacturer (OEM) level. Radiological inspection can also potentially detect unintentional damage to the part resulting from improper removal of part from assemblies, which may include, but not limited to, prolonged elevated temperature exposure during desoldering operations or mechanical stresses during removal. Radiological inspection of electronics includes film radiography and filmless radiography such as digital radiography (DR), real time radiography (RTR), and computed tomography (CT). Radiology is an important tool used in part verification of microelectronic devices. Radiographic analysis is performed on parts to verify that the internal package or die construction is consistent with an
This document establishes common industry practices and recommended screening, qualification, and lot acceptance testing of Plastic Encapsulated Microcircuits (PEMs) for use in space application environments.
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate up to and including 1.500 inches (38.10 mm) in thickness.
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This document covers insulated, flexible air duct assemblies for portable ground support air conditioners and heaters.
This SAE Aerospace Standard (AS) establishes the geometric control requirements for bolts, screws, and studs where worded notes and symbolized notes are used for straightness, concentricity, squareness, and runout.
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECU’s) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. The U.S. Environmental Protection Agency (EPA) and the California Air
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Aerospace Standard (AS) defines the items that shall be considered when creating a fiber optic cable assembly specification and source control drawing intended for installation on aerospace platforms.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
Items per page:
50
1 – 50 of 221567