Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This procedure describes a method of measuring the resistance to wet color transfer of materials such as textiles, leather, and composites.
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This AIR presents an abbreviated review of the metallurgical phenomena known as whiskers. It is not all encompassing; rather, it is intended to introduce the design engineer to the technical issues of metallic whiskers, their formation, and the potentially dangerous problems they can cause.
This document establishes the requirements for the sequencing of processes relating to parts fabricated from 300M or 4340 modified steel heat treated to, or to be heat treated to, 270,000 psi (1860 MPa) minimum ultimate tensile strength (UTS) and higher.
This recommended practice describes the physical and chemical characterization techniques for identification of epoxy adhesive and prepreg resin systems in order to verify the chemical formulation, resin B-staging (See 8.1), cure reaction rates, adhesive moisture content, and resin component mix ratios, as necessary to achieve manufacturing and quality producibility and engineering performance.
This document describes the materials, equipment, and processing techniques utilized in the fabrication of polyimide printed wiring boards. Included are recommendations for both double-sided and multilayer boards.
This SAE Aerospace Information Report (AIR) provides a general description of methods for hardness testing of O-rings including factors which affect precision and comparison of results with those obtained in standard tests.
This document describes an inspection procedure for detecting, by use of a radiographic opaque tracer and fluoroscopy or radiography methods, flaws which have been produced as the result of cutting, machining, or drilling operations in composite or laminate structures.
This detail specification, along with AMS6562, establishes the requirements for continuous E-glass fabric impregnated with a medium temperature, out-of-autoclave, oven-vacuum-bag cure modified B-staged epoxy resin. The prepreg is produced using a one side coated (one side tacky) hot-melt process.
This material has resistance to diester-based engine oil (MIL-PRF-7808) and fuel, but usage is not limited to such applications. This material is not suitable for use in synthetic phosphate ester based hydraulic fluids (AS1241) or helicopter transmission lubricating oils (DOD-PRF-85734, MIL-PRF-32538). For gas turbine engine lubricating oils (AS5780, MIL-PRF-23699), resistance varies by class and should be evaluated individually (see Note regarding high performance oils). This material has a typical service temperature range of -70 to +392 °F (-56.7 to +200 °C) for Class 1 and Class 2 and -70 to +437 °F (-56.7 to +225 °C) for Class 3. The service temperature range of the material is a general temperature range, but the presence of particular fluids and specific design requirements may modify this range. Each application should be considered separately. It is the responsibility of the user to determine that this specification is appropriate for the environments (temperature range
This SAE Aerospace Standard defines the requirements for establishing a nondestructive inspection (NDI) program for aerospace systems to include but not limited to aircraft structure, aircraft stores (external structures such as antennas, pods, fuel tanks, weapons, radomes, etc.) and missile/rocket structural components when an NDI Program Plan is required by contract. NDI Programs are essential to ensuring NDI processes are implemented to support the lifecycle design requirements of the system and its components. NDI Programs are applicable to all phases of the system life cycle, including acquisition, modification, and sustainment. This standard may also be applicable to mechanical equipment, subsystems, and propulsion systems, but the requirements defined by the NDI Program Plan should be tailored by the contracting agency for such use. An NDI Program Plan shall be developed at the beginning of the technology development phase and shall define all NDI requirements to be adhered to
This SAE Aerospace Recommended Practice (ARP) contains guidance to assist users by providing a method to install an AS6224/2 repair sleeve.
Items per page:
50
1 – 50 of 216063