Results
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
This specification covers the installation of aircraft interior lighting for military aircraft.
This SAE Aerospace Recommended Practice (ARP) describes a method for evaluating the performance of filter elements designed for aerospace hydraulic systems. The performance is measured and reported in terms of filtration ratios and stabilized contamination levels while testing with cyclic flow.
This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance).
This document outlines the most common repairs used on landing gear components. It is not the intention of this AIR to replace overhaul/component maintenance or technical order manuals, but it can serve as a guide into their preparation. Refer to the applicable component drawings and specifications for surface finish, thickness, and repair processing requirements. This document may also be used as a guide to develop an MRB (Material Review Board) plan. The repairs in this document apply to components made of metallic alloys. These repairs are intended for new manufactured components and overhauled components, including original equipment manufacturer (OEM)/depot and in-service repairs. The extent of repair allowed for new components as opposed to in-service components is left to the cognizant engineering authorities. Reference could be made to this document when justifying repairs on landing gears. For repairs outside the scope of this document, a detailed justification is necessary
This specification covers continuous, multiple-strand, roving of Type "S-2" glass impregnated with a heat-curable epoxy resin matrix and processed to a "B" stage condition.
This SAE Aerospace Information Report (AIR) provides methodologies and approaches that have been used to install and integrate full-authority-digital-engine-control (FADEC) systems on transport category aircraft. Although most of the information provided is based on turbofan/turboprop engines installed on large commercial transports, many of the issues raised are equally applicable to corporate, general aviation, regional, and commuter aircraft, and to military installations, particularly when commercial aircraft are employed by military users. The word “engine” is used to designate the aircraft propulsion system. The engine station designations used in this report are shown in Figures 1 to 3. Most of the material concerns an electronic engine control (EEC) with its associated software and its functional integration with the aircraft. However, the report also addresses the physical environment associated with the EEC and its associated wiring and sensors. Since most current transport
This SAE Standard provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
This specification covers the requirements for six alloy compositions, four inspection classes, four radiographic quality grades and six classes of mechanical properties of high strength aluminum-alloy castings.
The accompanying mounting and gear locations are applicable for all general installations of power take-off on the transmission gear box of motor trucks and tractors where the size of the transmission permits. The heavy-duty type opening can be adapted to the regular-duty type by the use of an adapter with 6.35 mm (0.25 in) flange thickness with appropriate bolt pattern and thread engagement. (See Figures 1 and 2.)
Electric, Fuel Cell and Hybrid vehicles may contain many types of high voltage systems. Adequate barriers between occupants and the high voltage systems are necessary to provide protection from potentially harmful electric current and materials within the high voltage system that can cause injury to occupants of the vehicle during and after a crash. This SAE Recommended Practice is applicable to Electric, Fuel Cell and Hybrid vehicle designs that are comprised of at least one vehicle propulsion voltage bus with a nominal operating voltage greater than 60 and less than 1,500 VDC, or greater than 30 and less than 1,000 VAC. This Recommended Practice addresses post-crash electrical safety, retention of electrical propulsion components and electrolyte spillage.
This SAE Standard specifies the essential interface dimensions, the installation dimensions, and the operating requirements for hydraulic couplers employed to transmit hydraulic power from agricultural tractors to agricultural implements and farmstead equipment as defined in SAE J1150.
This Information Report presents background and rationale for SAE Recommended Practice J1106, Laboratory Testing Machine and Procedures for Measuring the Steady Force and Moment Properties of Passenger Car Tires. The purpose of SAE J1106 is to define standards for equipment design and test procedures so that data from different laboratories can be directly compared. Whereas such standardization is not a requirement for testing associated with tire development, it is necessary in the context of vehicle design and tire selection problems. The basic approach employed in developing SAE J1106 was to consolidate and document existing technology as embodied in equipment and procedures currently employed for routine tire evaluations. Equipment and procedures whose current use is restricted to research applications were not considered. Research experience is discussed in this Information Report, however, to the extent deemed necessary to provide background and rationale for SAE J1106. Material
CLARA identifies four functions: Data Space Generator, Truth Data Generator, Coefficient Generator, and Reconstructor. Together these four functions standardize the solution to the LAR problem. This ICD defines the logical interfaces of the four functions.
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling, and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling oxygen cylinders while installed on aircraft, directly or through an intermediate charging port.
This specification covers one type of quartz cloth impregnated with a heat-reactive, thermosetting, polyimide resin system, the resin being processed to a "B" stage condition, and furnished in continuous rolls of full width material.
This Aerospace Standard (AS) 5659/4 Physical Layer Specification provides guidance for the physical layer of optical networks which use Wavelength Division Multiplexing (WDM), within the AS5659 WDM LAN specification document family. The physical layer consists of the optical interconnections between the functional components of the network. Performance requirements for general interconnections are described. For guidance, standards are identified, corresponding to each of several environments, which describe physical layer design, installation, maintenance, and training.
This SAE Aerospace Information Report (AIR) provides data and general analysis methods for calculation of internal and external, pressurized and unpressurized airplane compartment pressures during rapid discharge of cabin pressure. References to the applicable current FAA and EASA rules and advisory material are provided. While rules and interpretations can be expected to evolve, numerous airplanes have been approved under current and past rules that will have a continuing need for analysis of production and field modifications, alterations and repairs. The data and basic principles provided by this report are adaptable to any compartment decompression analysis requirement.
This SAE Standard defines a method for evaluating the immunity of automotive electrical/electronic devices to radiated electromagnetic fields coupled to the vehicle wiring harness. The method, called bulk current injection (BCI), uses a current probe to inject RF onto the wiring harness in the frequency range of 1 to 400 MHz. BCI is one of a number of test methods that can be used to simulate the electromagnetic field. The test method refers to ISO 11452-4 (please refer to ISO 11452-4 for test procedures). In addition to ISO 11452-4, this test method also includes a differential bulk current injection (DBCI) test. DBCI is described in Section 4 of this document.
Most signal and marking lighting devices have light sources (bulbs), which can be based on either filament or LED technology. To assure field replacement, it is important that light source types employed be readily available in normal service channels. This document defines the physical, electrical, and photometric characteristics necessary to achieve a proper replacement for popular types of signal and marking light sources. Some of the design characteristics in this document are listed solely for the sake of standardization and are not intended to describe the performance of lighting devices (lamp assemblies) on the vehicle. Halogen filament light sources suitable for signal and marking lighting are specified in SAE J2560.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film, supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
This document defines the requirements for weld fittings and machine weldments using an orbiting welding head suitable for use on cold worked 3AL-2.5V titanium, 21Cr-6Ni-9Mn CRES, and 718 nickel alloy tubing. Fitting standards covered by this specification include non-separable welded elbow, tee, and reducer fittings, and reconnectable 24-degree cone fittings, such as sleeves and unions.
This AS defines instruments which use inputs of static and pitot pressure equal to those which are utilized to establish the pressure altitude and speed of that aircraft. These pressures are applied to the instrument ports to provide means for generation of an aural warning whenever the aircraft reaches or exceeds the maximum operating limit speed. This Over Speed Warning Instrument function may be incorporated as part of an Air Data Computer, or an Air Speed Indicator, or an Air Speed/Mach Number Indicator, or other instruments. In those cases where the Over Speed Warning Instrument is part of another instrument, the standards contained herein apply only to the Over Speed Warning Instrument function. Each aircraft type and model has a defined maximum operating limit speed curve or curves which are a part of the airframe manufacturer's type certification approval data; this limit speed data shall be available from the subject airframe manufacturer as published in the operating manual
This procurement specification covers aircraft quality solid rivets and tubular end rivets made from a corrosion-resistant steel of the type identified under the Unified Numbering System as UNS S30200.
Items per page:
50
1 – 50 of 222094