Results
This SAE Aerospace Information Report (AIR) discusses past and present approaches for monitoring the landing gear structure and shock absorber (servicing), opportunities for corrosion detection, methods for transient overload detection, techniques for measuring the forces seen by the landing gear structure, and methods for determining the fatigue state of the landing gear structure. Landing gear tire condition and tire pressure monitoring are detailed in ARP6225, AIR4830, and ARP6137, respectively. Aircraft Brake Temperature Monitoring Systems (BTMS) are detailed in AS1145.
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
The purpose of this SAE Aerospace Information Report (AIR) is to disseminate qualitative information regarding foreign object debris (FOD) damage to the gas path of rotorcraft gas turbine engines and to discuss methods of FOD prevention. Although turbine-powered fixed-wing aircraft are also subject to FOD, the unique ability of the rotorcraft to hover above, takeoff from, and land on unprepared surfaces creates a special need for a separate treatment of this subject.
This Aerospace Information Report (AIR) will examine considerations relative to the use of mechanical switches on aircraft landing gear, and present "lessons learned" during the period that these devices have been used.
This SAE Information Report should be used as a supplement to SAE J1383 (Reference 2.1.1). It is intended to provide additional information which is important to the automotive designer and engineer in the process of designing, developing, and engineering the headlamps of motor vehicles which will take into account the effects of the aging process on the driver.
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECU’s) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. The U.S. Environmental Protection Agency (EPA) and the California Air
This ARP describes methods that are known to have been used by aircraft manufacturers to evaluate aircraft aerodynamic performance and handling effects following application of aircraft ground deicing/anti-icing fluids (“fluids”), as well as methods under development. Guidance and insight based upon those experiences are provided, including: Similarity analyses. Icing wind tunnel tests. Flight tests. CFD and other numerical analyses. This ARP also describes: The history of evaluation of the aerodynamic effects of fluids. The effects of fluids on aircraft aerodynamics. The testing for aerodynamic acceptability of fluids for SAE and regulatory qualification performed in accordance with AS5900. Additionally, Appendices A to E present individual aircraft manufacturers’ histories and methodologies, which substantially contributed to the improvement of knowledge and processes for the evaluation of fluid aerodynamic effects, and Appendix F considers the modeling of fluid removal from
This SAE Aerospace Standard (AS) establishes the minimum requirements for ground-based aircraft deicing/anti-icing methods and procedures to ensure the safe operation of aircraft during icing conditions on the ground. This document does not specify the requirements for particular aircraft models. The application of the procedures specified in this document are intended to effectively remove and/or prevent the accumulation of frost, snow, slush, or ice contamination which can seriously affect the aerodynamic performance and/or the controllability of an aircraft. The principal method of treatment employed is the use of fluids qualified to AMS1424 (Type I fluid) and AMS1428 (Type II, III, and IV fluids). All guidelines referred to herein are applicable only in conjunction with the applicable documents. Due to aerodynamic and other concerns, the application of deicing/anti-icing fluids shall be carried out in compliance with engine and aircraft manufacturer’s recommendations.
This specification covers a corrosion and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
This SAE Standard applies to off-road, self-propelled work machines used in earth moving, agriculture, and forestry as defined in SAE J1116, and establishes the following minimum performance levels in the operator's environment for the seated position:
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both 37 degree flared and pipe threaded connections for use in all types of fluid systems.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both flanged fitting ends and beaded hose connections for use in all types of fluid systems.
This document defines the requirements for polytetrafluoroethylene (PTFE) lined, para-aramid reinforced, hose assemblies suitable for use in 275 °F (135 °C), 5080 psi (35000 kPa) aircraft hydraulic systems.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement HONDA_DIAGH within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/4_0500 interface shall be compliant to the HONDA_DIAGH feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This SAE Aerospace Standard (AS) defines the requirements for air cycle air conditioning systems used on military air vehicles for cooling, heating, ventilation, and moisture and contamination control. General recommendations for an air conditioning system, which may include an air cycle system as a cooling source, are included in MIL-E-18927E and JSSG-2009. Air cycle air conditioning systems include those components which condition high temperature and high pressure air for delivery to occupied and equipment compartments and to electrical and electronic equipment. This document is applicable to open and closed loop air cycle systems. Definitions are contained in Section 5 of this document.
This specification covers procedures for sampling and testing aircraft-quality, special aircraft-quality, and premium aircraft-quality steels requiring transverse tensile property testing.
This document applies to prognostics of aerospace propulsion systems. Its purpose is to define the meaning of prognostics in this context, explain their potential and limitations, and to provide guidelines for potential approaches for use in existing condition monitoring environments. This document also includes some examples. The current revision does not provide specific guidance on validation and verification, nor does it address implementation aspects such as computational capability or certification.
This Aerospace Standard (AS) is to be used as a supplement to SAE AS7112. In addition to the requirements specified in AS7112, the requirements specified herein shall apply to suppliers seeking Nadcap Fluid System accreditation for manufacturing titanium 3AI-2.5V alloy, seamless hydraulic tubing. The corresponding PRI Audit Criteria (AC) is to be applied to ensure the tubing is manufactured to the applicable specification(s) and standard(s).
Items per page:
50
1 – 50 of 222750