Results
This SAE Recommended Practice is applicable to all heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine the heat transfer and pressure drop performance of heat exchangers under specified conditions. This document has been reviewed and revised by adding several clarifying statements to Section 4.
This SAE Recommended Practice applies to mobile cranes when used in lifting crane service that are equipped with boom length indicating devices.
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm), inclusive, in thickness, supplied in the -T361 temper (see 8.5).
This SAE Aerospace Standard defines a typical coupling (with different fitting end styles), which is used in typical cone connection fittings installed in high-pressure (up to 3000 psi) oxygen systems for the purpose of mating to applicable oxygen equipment. Dimensions are developed from AND10089 and AS4375.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up trucks with dual wheels, and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal to the driver of following (approaching a signaling vehicle from the rear) or oncoming (approaching a signaling vehicle from the front) vehicles over intervening vehicles.
AMS4269C has been declared “STABILIZED” by SAE AMS Committee D Nonferrous Alloys and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability of technical requirements. Newer technology may exist.
This specification covers one type of copper-beryllium alloy in the form of sheet, strip, and plate (see 8.6).
This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm) in nominal diameter or least distance between parallel sides, inclusive, and stock for forging of any size (see 8.7).
This document provides vehicle-level data collection, data analysis, and data verification procedures that may be used to verify that an instrument under test (IUT) satisfies the vehicle-level requirements specified in SAE J3161/1. For the purposes of this report, “vehicle-level requirements” primarily consist of those requirements which can be verified external to the vehicle. The IUT for these procedures is a configured LTE-V2X vehicle-to-vehicle (V2V) device as defined in SAE J3161/1 and is installed on a vehicle of class 2, 3, 4, or 5. While the IUT is conceptually separated from the vehicle it is installed on, the tests outlined in this document are primarily vehicle level, so the terms “vehicle” and “IUT” can generally be considered interchangeable. Additionally, non-vehicle-level complementary tests, not included in this document, are required to verify that the entire set of requirements specified in SAE J3161/1 is satisfied. This document also includes a Traceability Matrix to
This specification covers an aluminum alloy in the form of sheet and plate, alclad both sides, supplied in the -T361 temper.
This document describes a physical layer utilizing Unshielded Twisted Pair (UTP) cable with extended stub lengths for flexibility in ECU placement and network topology. Also, connectors are not specified. CAN controllers used on SAE J1939-15 networks must be restricted to use only Classical Frames as defined in ISO 11898- 1. A network which may have legacy controllers cannot tolerate FD Frames. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
SAE J1939-31 network layer describes the requirements and services for network interconnection ECUs (NIECU) that enable electronic control units (ECUs) on an SAE J1939 network segment to intercommunicate with other ECUs on different network segments of the vehicle or system network. This document defines various types of NIECUs. The information in this document applies only to ECUs that are intended to provide networking services. It is not necessary for an ECU to provide any of these services in order to be compliant with the SAE J1939 protocol.
SAE J1939-81 (“Network Management”) defines the processes and messages associated with managing the addresses of applications communicating on an SAE J1939 network. Network management is concerned with the management of addresses and the association of those addresses with an actual function and with the detection and reporting of network related errors. Due to the nature of management of addresses, network management also specifies address selection and address claiming processes, requirements for reaction to brief power outages, and minimum requirements for ECUs on the network.
SAE J1939-13 specifies the diagnostic connectors used for off-board connection to a vehicle’s SAE J1939 communication links. The defined diagnostic connectors support connection to the twisted shielded pair media (refer to SAE J1939-11), the unshielded twisted pair (refer to SAE J1939-15), the twisted pair (refer to SAE J1939-14), and the twisted unshielded quad media (refer to ISO 11783-2).
SAE J1939-82 compliance describes the compliance tests and procedures to verify an SAE J1939 electronic control unit (ECU) operates correctly on a SAE J1939 network. The purpose of these compliance procedures is to generate one or more test documents that outline the tests needed to assure that an ECU that is designed to operate as a node on a SAE J1939 network would do so correctly. SAE does not certify devices and these tests and their results do not constitute endorsement by SAE of any particular ECU. These tests are presented to allow testing of an ECU to determine self-compliance by the manufacturer of an ECU. The manufacturer can use its record of what procedures were run successfully to show the level of compliance with SAE J1939.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
SCOPE IS UNAVAILABLE.
This SAE Aerospace Standard (AS) covers miniature, composite, high density, threaded coupling, self-locking, circular, environment-resistant, electrical connectors utilizing removable crimp contacts, and associated hardware, which are capable of continuous operation within a temperature range of -65 to +175 °C (-85 to 347 °F). These connectors are supplied under an AS9100 reliability assurance program. See 6.1 for intended use and applications.
The purpose of this test is to evaluate the axial strength of the nut seat of wheels intended for use on passenger cars, light trucks, and multipurpose vehicles. In addition, a minimum contact area is recommended to ensure enough strength for the rotational force in tightening a nut against the nut seat. While this test ensures the minimum strength of the nut seat, the wheel must also have a degree of flexibility. This flexibility, as well as bolt tension, are important to maintain wheel retention.
This SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available.
This SAE Aerospace Information Report (AIR) covers the design parameters for various methods of humidification applicable to aircraft, the physiological aspects of low humidities, the possible benefits of controlling cabin humidity, the penalties associated with humidification, and the problems which must be solved for practical aircraft humidification systems. The design information is applicable to commercial and military aircraft. The physiological aspects cover all aircraft environmental control applications.
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This document covers the recommended lighting performance and design criteria for: Left Forward Navigation Position Lights (Red) Right Forward Navigation Position Lights (Green) Rear Navigation Position Lights (White) Anticollision Lights. AS8017 provides for the following classes: Class I Rotorcraft, Class II Fixed Wing, and Class III Fixed Wing and Rotorcraft. Possible design requires include but are not limited to: Red Flashing Lights Top and Bottom Fuselage White Flashing Strobe Lights Wing Tips and/or Tail Red Flashing Beacon Light on Top of Vertical Tail
SAE J1939-75 defines the set of data parameters (SPs) and messages (PGs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPs) and messages (PGs) previously published within this document are published in SAE J1939DA. Applications using the SAE J1939-75 document must refer to SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road, as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-21, describes the data link layer using the Classical Extended Frame Format (CEFF) with 29-bit IDs, as defined in ISO 11898-1, December 2015. For SAE J1939, no alternative data link layers are permitted.
This specification covers the requirements for application to fasteners of a corrosion and heat resistant aluminum coating material having a thermosetting inorganic binder and the properties of the finished coating.
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
Items per page:
50
1 – 50 of 215744