Results
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test Almen strip holder is required for intensity determination.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing, or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
This SAE Aerospace Information Report (AIR) covers the general requirements for, and the listing of, manufacturers’ identification markings, names, symbols or trademarks, and CAGE codes that appear on electrical and electronic wiring devices and accessories as required by individual product specifications. Supplier markings from previous submitted listings are maintained for component traceability.
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This document is intended to establish a procedure to certify AD fallback test driver skill levels as an endorsement to SAE J3300 foundational level certification. The SAE J3300/3 endorsement can be used by the individual driver to qualify their skills as a test driver of vehicles with automated driving features. The SAE J3300/3 endorsement levels may also be used by test facilities or other organizations when seeking test or professional drivers with these skills. This document provides directions for obtaining the endorsement, including associated AD fallback test driving skill examination requirements, through SAE J3300-certified Examiners (refer to SAE J3300 for definition). Endorsement registration and associated records are administered through Probitas Authentication®. Probitas Authentication® is the current Independent Program Administrator for the SAE J3300 series. This document is a supplement to SAE J3300, providing information specific to the AD fallback test driver skill
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) air and is not directly applicable to vehicles with other systems. Air over hydraulic systems are to be tested as air systems.
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
This specification covers a copper-beryllium alloy in the form of sand, investment, or centrifugal castings.
This paper describes a recommended practice and procedure for the correlation of test cells that are used for the performance testing of turboprop and turboshaft engines. This Aerospace Recommended Practice (ARP) shall apply to both dynamometer and propeller based testing. Test cell correlation is performed to determine the effect of any given test cell enclosure and equipment on the performance of an engine relative to the baseline performance of that engine. Although no original equipment manufacturer (OEM) documents are actually referenced, the experience and knowledge of several OEMs contributed to the development of this document. Each engine manufacturer has their own practices relating to correlation and they will be used by those OEMS for the purpose of establishing certified test facilities.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
This specification established (1) the common requirements for hydraulic units capable of functioning as starters and as pumps suitable for use in aircraft and missiles and (2) the methods to be used for demonstrating compliance with these requirements.
This SAE Aerospace Standard (AS) establishes supplemental requirements for 9100 and 9145 and applies to any organization receiving it as part of a purchase order or other contractual document from a customer. AS13100 also provides details of the reference materials (RM13xxx) developed by the SAE G-22 AESQ committee and listed in Section 2 that can also be used by organizations in conjunction with this standard.
This specification covers a premium aircraft-quality corrosion and heat-resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Recommended Practice defines the test stand and procedure for evaluating radial impacts of all wheels intended for passenger cars and light trucks. A minimum performance requirement is intentionally not provided. The intent is to establish a uniform method and test stand for imparting damage and evaluating radial impacts. A minimum performance requirement will be a proposed change when users determine what is of most value.
Items per page:
50
1 – 50 of 222189