Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This SAE Aerospace Standard (AS) defines the requirements for heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in 400 °F, 3000 psi aircraft hydraulic systems. Assemblies are suitable where rapid rate pressure pulsing and torsional/ longitudinal flexing may occur, in addition to normal hydraulic system loads.
This document outlines the evaluation and documentation appropriate when the components of an approved aircraft seat restraint system are replaced or modified by a party other than the Original Equipment Manufacturer of the restraint system.
The purpose of this SAE Aerospace Standard (AS) is to standardize the basic design, performance, and testing requirements for “Cargo Stoppers” cargo tie-down accessories to be used in conjunction with approved restraint straps meeting AS5385C (TSO C-172) requirements.
Through the use of ultra-high frequency ultrasound, typically above 10 MHz, Acoustic Microscopy (AM) non-destructively finds and characterizes physical features and latent defects (visualization of interior features in a layer by layer process) - such as material continuity and discontinuities, sub-surface flaws, cracks, voids, delaminations and porosity. AM observed features and defects can be indicators that the components were improperly handled, stored, altered or previously used. If AS6171/6 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
An attempt has been made to consider all features of seal ring design including configuration, materials, hardness, dimensions, surface finishes, surface treatment, leak testing, and general quality. In addition to this, allowable cylinder breathing and general quality requirements of mating hardware are discussed. Also, at the end of this report, there is a brief paragraph on other types of seal rings.
This SAE Standard sets forth the procedures to be used in measuring sound levels and determining the time weighted sound level at the operator's station(s) of specified off-road self-propelled work machines. This document applies to the following work machines which have operator stations as specified in SAE J1116: • Crawler Loader • Grader • Log Skidder • Wheel Loader • Crawler Tractor with Dozer • Pipelayer • Dumper • Wheel Tractor with Dozer • Trencher • Tractor Scraper • Backhoe • Sweeper • Roller/Compactor • Hydraulic Excavator • Pad Foot Wheel Compactor with Dozer • Excavator and Wheel Feller-Buncher The instrumentation requirements and specific work cycles for these machines are described. The method used to calculate the time weighted average sound level at the operator station(s) is specified for Leq(5), or optional exchange rates, during continuous operation in a work cycle representing continuous medium to heavy work. The work cycles provide a repeatable reproduceable means
This SAE Aerospace Recommended Practice (ARP) describes the continuous sampling and analysis of gaseous emissions from aircraft gas turbine engines. The measured gas species include carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), hydrocarbons (HC), and water vapor (H2O). This ARP excludes engine operating procedures and test modes, and is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode. It is recognized that there will probably be major advances in the gas analysis measurement technology. It is not the intent of this ARP to exclude other analysis techniques, but to form the basis of the minimum amount of conventional instruments (those in common industry usage over the last fifteen years) required for the analysis of aircraft engine exhaust. It is the responsibility of the analyst to demonstrate the alternative measurement technology has comparable (or better) performance than the techniques
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches (127.00 mm), inclusive, in nominal diameter or least thickness between parallel sides (bars, rods, wire, profiles) or nominal wall thickness (tubing) (see 8.5).
This SAE Aerospace Recommended Practice (ARP) contains the general requirements and test procedures for Dual Mode (NVIS Friendly visible and Covert) exterior lighting for most rotorcraft and fixed wing aircraft and could be applicable to ground vehicles that desire a Dual Mode lighting system.
This standard covers all types of oxygen breathing equipment used in non-military aircraft. It is intended that this standard supplements the requirements of the detail specification or drawings of specific components or assemblies (e.g., regulators, masks, cylinders, etc.). Where a conflict exists between this standard and detail specifications, detail specifications shall take precedence.
This SAE Recommended Practice identifies and defines the specifications most commonly used to describe high-speed steel track and articulated rubber-tired clam bunk skidders. The illustrations used are not intended to be descriptive of any existing machine or dictate a combination needed for a particular logging situation. The dimensions indicated are basic and may be supplemented by the individual machine manufacturer.
The content of ARP6328 contains guidance for implementing processes used for risk identification, mitigation, detection, avoidance, disposition, and reporting of counterfeit electrical, electronic, and electromechanical (EEE) parts and assemblies in accordance with AS5553 Revision D. This document may also be used in conjunction with other revisions of AS5553. This document retains guidance contained in the base document of AS5553, updated as appropriate to reflect current practices. This is not intended to stand alone, supersede, or cancel requirements found in other quality management system documents, requirements imposed by contracting authorities, or applicable laws and regulations unless an authorized exemption/variance has been obtained.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.
This specification applies to a communication protocol for networked control systems. The protocol provides peer-to-peer communication for networked control and is suitable for implementing both peer-to-peer and master-slave control strategies. This specification describes services for all seven protocol layers. In the layer 7 specification, it includes a description of the types of messages used by applications to exchange application and network management data.
This document establishes techniques for validating that an Aircraft Station Interface (ASI) complies with the interface requirements delineated in MIL-STD-1760B Notice 3. For validation of aircraft designed to MIL-STD-1760A Notice 2 AS4764 Issued 1995-04 applies.
This SAE Standard applies to lead-acid 12 V heavy-duty storage batteries as described in SAE J537 and SAE J930 for uses in starting, lighting, and ignition (SLI) applications on motor vehicles and/or off-road machines. These applications have some of the following characteristics: High levels of power are required to start the vehicle’s internal combustion engine. The need to supply this power limits the maximum depth of discharge to a fraction of the total capacity of the battery. The battery must be maintained at a charge level sufficient to perform this primary function by the vehicle’s voltage-regulated charging system. The vehicle’s engine powers a voltage-regulated charging system that limits the charging voltage when spinning at sufficient speed and when total loads do not exceed its output limits. The battery is subject to deeper discharging than a typical automotive application as a result of the following conditions: High daily hours of use High numbers of starts per day
This SAE Standard establishes a uniform test procedure and performance requirements for the ventilation system(s) of personal watercraft. This SAE Standard does not apply to outboard powered personal watercraft and jet powered surfboards.
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, and components. Said actuators are used for applying cam type foundation brakes by slack adjuster means.
This SAE Standard pertains to off-road, self-propelled work machines as defined in categories one through five of SAE J1116. It is intended to provide engineers and designers with information in order that access openings provided in equipment and machinery for purposes of inspection, adjustment, and maintenance are made large enough for the intended function by the person in the field or shop.
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
This report identifies the reasons for, and results associated with, the conduct of a flight simulation research project evaluating the effect of low powered laser beam illumination of pilot crewmembers operating in the navigable airspace. This evaluation was primarily concerned with the possible degradation of pilot performance when illuminated by a laser while operating in an airport terminal area where pilot workloads are normally at their maximum.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements and procedures for three classes of gas, vacuum, liquid, and low-pressure carburizing (LPC) and related heat treatment of parts fabricated from carburizing-grade steels. Parts made from steels other than those specified in the detail specifications may be heat treated in accordance with the applicable requirements using processing temperatures, times, and other parameters recommended by the material producer. This specification does not cover pack carburizing.
This test method outlines the recommended machine function, fixtures, and procedures used to test airframe rolling element bearings for dynamic performance under steady unidirectional radial load and oscillatory motion. Bearings covered by this test method shall be ball, roller, or needle type in either annular or rod end configuration, used in airframe control applications.
This Aerospace Standard (AS) defines the requirements for a metallic reinforced, duct assembly suitable for use in low pressure, 350 °F ground heaters.
Items per page:
50
1 – 50 of 221567