Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This document establishes the requirements for screw-on type reattachable couplings for use in low temperature hose assemblies.
This SAE Surface Vehicle Technical Information Report, SAE J2836/4, establishes diagnostic use cases between plug-in electric vehicles (PEV) and the electric vehicle supply equipment (EVSE). As PEVs are deployed and include both plug-in hybrid electric (PHEV) and battery electric (BEV) vehicle variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document describes the general information required for diagnostics and SAE J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
This SAE Aerospace Information Report (AIR) provides an orientation regarding the general technology of chemical oxygen generators to aircraft engineers for assistance in determining whether chemical oxygen generators are an appropriate oxygen supply source for hypoxia protection in a given application and as an aid in specifying such generators. Information regarding the details of design and manufacture of chemical oxygen generators is generally beyond the scope of this document.
This standard covers oronasal type masks which use a continuous flow oxygen supply. Each such mask comprises a facepiece with valves as required, a mask suspension device, a reservoir, or rebreather bag (when used), a length of tubing for connection to the oxygen supply source, and a means for allowing the crew to determine if oxygen is being delivered to the mask. The assembly shall be capable of being stowed suitably to meet the requirements of its intended use.
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
This SAE Aerospace Information Report (AIR) outlines a recommended procedure for evaluation of the vibration environment to which the gas turbine engine powerplant is subjected in the helicopter installation. This analysis of engine vibration is normally demonstrated on a one-time basis upon initial certification, or after a major modification, of an engine/helicopter configuration. This AIR deals with linear vibration as measured on the basic case structure of the engine and not, for example, torsional vibration in drive shafting or vibration of a component within the engine such as a compressor or turbine airfoil. In summary, this AIR discusses the engine manufacturer’s "Installation Test Code" aspects of engine vibration and proposes an appropriate measurement method.
This SAE Aerospace Recommended Practice (ARP) identifies and defines a method of measuring those factors affecting installed power available for helicopter powerplants. These factors are installation losses, accessory power extraction, and operational effects. Accurate determination of these factors is vital in the calculation of helicopter performance as described in the RFM. It is intended that the methods presented herein prescribe and define each factor as well as an approach to measuring said factor. Only basic installations of turboshaft engines in helicopters are considered. Although the methods described may apply in principle to other configurations that lead to more complex installation losses, such as an inlet particle separator, inlet barrier filter (with or without a bypass system), or infrared suppressor, specialized or individual techniques may be required in these cases for the determination and definition of engine installation losses. Some rotorcraft may use an
This SAE Aerospace Standard (AS) offers gland details for a 0.364 inch (9.246 mm) cross-section gland (nominal 3/8 inch) with proposed gland lengths for compression-type seals with two backup rings over a range of 7 to 21 inches (178 to 533 mm) in diameter. The dash number system used is similar to AS568A. A 600 series has been chosen as a logical extension of AS568A, and the 625 number has been selected for the initial number, since 300 and 400 series in MIL-G-5514 and AS4716 begin with 325 and 425 sizes. Seal configurations and design are not a part of this document. This gland is for use with compression-type seals including, but not limited to, O-rings, T-rings, D-rings, cap seals, etc.
This standard defines the common nonconformity data definition and documentation that shall be exchanged between an internal/external supplier or sub-tier supplier, and the customer when informing about a nonconformity requiring formal decision. The requirements are applicable, partly or totally, when reporting a product nonconformity to the owner or operator, as user of the end item (e.g., engine, aircraft, spacecraft, helicopter), if specified by contract. Reporting of nonconformity data, either electronically or conventionally on paper, is subject to the terms and conditions of the contract. This also includes, where applicable, data access under export control regulations.
The requirements established in this document are applicable to the IAQG and associated sectors for managing oversight to established requirements contained in 9104-series standards (i.e., 9104/1, 9104/2, 9104/3). The requirements are applicable to IAQG working groups for oversight. NOTE: All required forms are depicted in Appendix A. These form exhibits are provided for reference only; the current versions of these forms are available on the IAQG website.
This specification covers the specific requirements for 7075 aluminum alloy plate and sheet.
This specification covers a butadiene-acrylonitrile (NBR) rubber in the form of molded rings, compression seals, o-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications.
This specification covers polyurethane systems consisting of an isocyanate component and other components containing a polyol and other ingredients which, when mixed and cured, produce thermosetting, rigid, cellular products.
This specification covers electrical iron in the form of bar and strip.
This specification covers a polytetrafluoroethylene resin in the form of extruded and sintered flexible tube reinforced with wire braid.
This specification covers a silicone (MQ/VMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, AMS7268 should be used.
This specification covers a synthetic rubber sealing compound which is electrically conductive when used in a faying surface, contains corrosion inhibitors, and supplied as a two-component system which cures at room temperature, suitable for application by extrusion gun or spatula.
This specification covers a perfluoroether elastomer in the form of molded rings.
The scope of this SAE Aerospace Information Report (AIR) is to define recommended methods of determining the optimal dimensional relationship of components coupled together using thrust wires for applications such as coupling nuts and fittings. These design parameters are intended to optimize component loading characteristics and maximize wire shear capabilities for both high and low pressure applications.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7274 rubber. It shall be used for procurement purposes.
This specification covers the engineering requirements for heat treatment of magnesium alloy castings and for parts machined from castings.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers a low-carbon steel in the form of bars and wire 0.750 inch (19.05 mm) and under in nominal diameter or distance between parallel sides.
This specification covers a corrosion and heat resistant work strengthened nickel alloy in the form of bars and wire, 1½ inches (38 mm) and under in nominal diameter (See 8.2).
This specification covers the specific requirements for improved exfoliation-resistant aluminum alloy, 7178-T76 sheet and 7178-T7651 plate.
This specification covers a corrosion-resistant steel in the form of plate up to 3.00 inches (76.2 mm), inclusive, in nominal thickness.
This specification has previously been widely used and may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does not recommend this specification for future use in new designs (See 6.7).
Items per page:
50
1 – 50 of 219833