Results
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This specification covers the installation of aircraft interior lighting for military aircraft.
This procurement specification covers aircraft-quality solid rivets made from a corrosion- and heat-resistant cobalt alloy of the type identified under the Unified Numbering System as UNS R30605.
This SAE Aerospace Recommended Practice (ARP) document establishes criteria and recommended practices for the use of airborne icing tankers to aid in design and certification of aircraft ice protection systems and components. Several icing tankers are described, along with their capabilities and suggested use. Sample data for these tanker spray systems are included, shown with 14 CFR Parts 25 and 29, Appendix C icing envelopes for continuous maximum and intermittent maximum icing conditions. (Note: In the remainder of this document, the phrase “Appendix C icing envelopes” will be used for brevity.) This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This specification covers an iron-nickel-cobalt alloy in the form of sheet, strip, and plate.
This SAE Recommended Practice defines a guideline for the fuel injection pump designer to select appropriate fastener designs which are considered to be tamper-resistant. It applies to fuel injection pumps used on diesel engines.
This practice provides a method for evaluating microhardness and microstructure very close (0.002 inch (0.051 mm) or less) to the surface of a disk specimen. Specific accept/reject criteria for partial decarburization (3.7.1), inadvertent carburization/nitriding (3.7.3), total decarburization/intergranular oxidation (3.8), and other characteristics evaluated are to be found in the applicable specification where this ARP is referenced.
The purpose of this document is to establish guidelines for determining the critical R134a and R1234yf refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and agricultural tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a and R1234yf refrigerant charge for the HVAC system.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers two types of an open-cell, medium-flexibility polyurethane foam in the form of sheet, strip, and shapes.
These requirements are applicable to IAQG sector schemes when making use of ABs, CRBs and their auditors, for the assessment and certification/registration of supplier quality systems in accordance with the requirements of this document. The quality management system standard used by the CRB shall be 9100/9110/9120, as appropriate to the supplier’s activities. It shall be applied to the supplier’s complete Quality System that covers aerospace products. Sectors may use these requirements for other standards. IAQG members have committed to recognize the equivalence of certification/registration of a suppliers quality management system to either of the AS, EN or JISQ/SJAC standards. This AS provides the approval process for Auditor Authentication Bodies (AAB), training course providers, trainers and auditors who meet the requirements of AIR5493 and outlines the America’s sector specific process to implement AS9104. This document is created to be in conformance with AS9104.
This Aerospace Recommended Practice (ARP) outlines the causes and impacts of moisture and/or condensation in avionics equipment and provides recommendations for corrective and preventative action.
This specification covers an aluminum alloy in the form of plate.
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) air and is not directly applicable to vehicles with other systems. Air over hydraulic systems are to be tested as air systems.
This SAE Recommended Practice defines the test stand and procedure for evaluating radial impacts of all wheels intended for passenger cars and light trucks. A minimum performance requirement is intentionally not provided. The intent is to establish a uniform method and test stand for imparting damage and evaluating radial impacts. A minimum performance requirement will be a proposed change when users determine what is of most value.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specification requirements of wrought carbon and low-alloy steel products and of forging stock.
Items per page:
50
1 – 50 of 222094